Removing a Broken Graphite Shaft 2019 -Golf Club Repair

No video

Removing a Broken Graphite Shaft 2019 -Golf Club Repair

Рет қаралды 93,599

Күн бұрын

We go over how to remove a golf shaft that is broken off at the hosel. Got questions please put them down below
For Golf Club Repair Tools, Golf Fitting Tools and Select OEM’s
Please see the link below.
www.amazon.com...
If you require Golf Club Repairs or would like to schedule a fitting for your best golf or have a question
Please contact us at
mcgolfshop@roadrunner.com
clubmaker@mcgolf.net
For more info please follow us on
Twitter
Instagram
IAMMCGOLF

Пікірлер: 55

@guitarsandgolfballs 5 жыл бұрын

Hi from England, at my first attempt at this I went through the hosel cap and nearly through the the other side of my favourite 3 wood. Didn't make that mistake again. Great video

@KentnDebi 5 жыл бұрын

Hi Jim, if you run a large wood screw into it (the shaft) you can pull the damaged tip section out in the usual way...heat an pull (spiral quik-outs will work also). Job done and no chance of damage from a drill bit :-)

@McGolf 5 жыл бұрын

Kent Nicholson I’ve seen a T handle with a screw attached which interests me. I can’t use a screw on my puller or it will damage the puller vice. That why I always try to get the shaft to grab with a smaller bit. Good tip!

@KentnDebi 5 жыл бұрын

@@McGolf Jim if you braze or epoxy the wood screw into an old shaft you can use it in your puller then...it just sits in like a normal pull would. I should have explained better, apologies

@thomasgossett8021 Жыл бұрын

❤How expensive is a new graflit shaft for a driver

@td1138 5 жыл бұрын

Awesome video! More stuff I did not know, and now I do. Thanks!

@hugo9071 9 ай бұрын

Best way to get it out without the mess is using a a screw that barely fits in the broken shaft. Heat the hosel then pull it with a pair of pliers.

@hanulategan5786 3 жыл бұрын

Hi how do you know when you have drilled for enough to not damage the inside? Busy with a SLDR shaft repair

@jimsmallwood6017 24 күн бұрын

I have a tailor-made stealth driver, I can loosen the screw in the head, but I cannot remove the club head from the shaft. Do you have any suggestions? Thank you.

@bleebleblahble8833 2 ай бұрын

Have you ever tried using left handed drill bits?

@garyyip8854 5 жыл бұрын

HI Jim, another great video. When doing the same repair I've mistakingly drilled right through the hosel cap (not as skilled as you). What would you do afterward? I usual put a plastic plug before reshafting. If there was a small bit that fell into the head, I put some rattle stop in there. Any other tips or recommendations? thanks again :D

@McGolf 5 жыл бұрын

Gary Yip I’ve drilled through it too, the rattle stop and plastic hosel plug are the way to go

@shiza237 2 жыл бұрын

great video, I have glue residue on the head as well as a graphite shaft snapped at the hosel.....How would you get the glue off the head? looks like gorilla glue

@stuarttampen8241 4 жыл бұрын

Hi, Could you use an easyout left hand thread that you would use to remove a broken bolt? This way you're not chancing drilling through the club head. Heat first then use a tap handle to turn the easyout anti-clock, this should grip the center of the broken shaft, loosen the glue and pull it out.

@McGolf 4 жыл бұрын

Stuart Tampen you could on steel and I do that for steel broken at the hosel. Graphite shafts May work if enough heat is applied or you will take out the inner layers and need a bigger easy out next.

@everestshrestha3434 Жыл бұрын

How do I know how far down to drill, like when to stop before going to far and drilling into the actual driver head?

@mattrevilock5890 5 жыл бұрын

Awesome content. Question:. Would you drill out a putter head like that? I hope all is well. Thanks for everything.

@McGolf 5 жыл бұрын

yes, it just takes less time

@forrestfrank1352 2 жыл бұрын

Help. I broke the shaft in my 7 iron. Ram fx2 with specific shafts. Took to a big box golf retailer that has a "Golf Pro". Was very specific that the shaft had to be the same specs... Weight, flex, length. Wanted the old shaft back. The new shaft doesn't feel the same. How do you verify the flex?

@SuperSeniorgolfer 4 жыл бұрын

Great video - I am having to do the same thing after my 3 wood met a root and the root won. What type of wheel did you use on the grinder to polish up the wood? I need to do that too before I reshaft it.

@TeamHeapMI 3 жыл бұрын

Looks like a type buff wheel

@AndrewMarshall2112 Жыл бұрын

What size drill bits did you use?

@McGolf 11 ай бұрын

5/16

@McGolf 11 ай бұрын

And smaller

@pappygamma 4 жыл бұрын

What is the max drill bit size

@makosharkcnc7730 2 ай бұрын

what size drill did you use?

@Funkengr00ven 4 ай бұрын

Is it possible to re-use the shaft? Asking for a friend.

@royrea1339 2 жыл бұрын

Jim, how do you remove a broken steel shaft from an iron?

@johnnowak 3 жыл бұрын

Hi Jim love your work.Can you tell me how to fill a dint on my Titleist 915 driver head,thanks.

@McGolf 3 жыл бұрын

no. dents are unfortunately a permanent fixture. I have heard of a guy the tried to use air. I doubt it worked.

@johnnowak 3 жыл бұрын

@@McGolf thanks

@Coachdenz11 3 жыл бұрын

what size drill bits?

@TOXICavengers 5 жыл бұрын

love your videos, how much space should there be between the hosel and shaft before gluing?

@McGolf 5 жыл бұрын

TOXICavengers about .01

@TOXICavengers 5 жыл бұрын

@@McGolf thank you. keep up the good work.

@andrewborbas9356 4 жыл бұрын

Thanks for the video! I have a Taylormade M2 fairway wood that I just bought used but shaft is busted right at the hosel! Can u explain how to remove busted shaft i.e. is it different than this video?

@wwclark 4 жыл бұрын

That’s pretty much what this video was

@chriswright9720 3 ай бұрын

M2 clubs usually just unscrew as they are adjustable