Repair Broken Car Disc Brakes With a Lathe | Perbaiki Cakram Rem Mobil dengan Mesin Bubut Working

No video

Repair Broken Car Disc Brakes With a Lathe | Perbaiki Cakram Rem Mobil dengan Mesin Bubut Working

Рет қаралды 820,103

3 жыл бұрын

Video ini menunjukkan bagaimana saya membubut discbrake, hal ini dilakukan apabila discbrake ngobeng atau pori-pori sudah tertutup

Пікірлер: 272

@kapatta 2 жыл бұрын

I would highly discourge. The thickness of break disc is an important parameter for safety and reliability. The moment disc go below minimum thickmess or significant area of contact with break pad is lost then it must be change

@chevybigblock3311 2 жыл бұрын

That would be why the spects are stamped in the hat of the rotor

@davidmarkwort9711 2 жыл бұрын

There are tolerances for the thickness of discs, so long as you adhere to these it is ok to either turn or grind the disc.

@dirtfishingdownunder 3 жыл бұрын

There is an underlying flaw with this process (excluding minimum thickness requirements). By not installing the hub mounting surface perfectly perpendicular to the rotating axis of the lathe, there will be brake pedal pulsation.

@Paul_Tomlin 3 жыл бұрын

If you watch the whole video he machines the hub mounting surface. Although that could in fact make the wheel wobble.

@dirtfishingdownunder 3 жыл бұрын

@@Paul_Tomlin I did watch the whole video, but the flawed logic still exists. If you watch carefully, you can see the run-out in the vented part of the disc. That's what initially caught my attention. Everything should be referenced to the hub face.

@Paul_Tomlin 3 жыл бұрын

@@dirtfishingdownunder yeah I agree for the most part it's not the right thing to do but hes done it as best as possible with what he has. Personally I would just run a orbital sander with some 60grit around both sides of the disk to rough it up abit and new pads, next time will need new disks.

@thomasblaine3193 3 жыл бұрын

Id just buy new rotors like i am doing now sitting in the dealership. Fun thing is last week they sent me home missing 3 nuts on one wheel. One on another. So 4 in total. They didnt even bothwr trying to put 4 on each wheel.... i could have lost my wheel this week.

@hojnikb 2 жыл бұрын

@@thomasblaine3193 In developing world, where labor is dirt cheap, resufacing might be the only option. 100-150$ for a set of discs might sound cheap to us, but could be someones entire moths or two wage.

@willacewallace5905 3 жыл бұрын

I like the wire used as a dial indicator!

@schnoggel 3 жыл бұрын

This would be impossible in Germany. The brake disc is too thin after turning and can break, which can be fatal for yourself and above all for others.

@bartekino 2 жыл бұрын

Für Optik geht es voll klar

@richhardchoppers7869 2 жыл бұрын

Yeah thats why we do it here not in your country 😀

@ardiwahdiana6366 2 жыл бұрын

Repair for save your cost ?? ,Why not ? 😀

@hendrahilmansyah446 2 жыл бұрын

Weh.....mantep jadi rapi lagi.......

@mtay65 3 жыл бұрын

Very good workmanship. Face all 3 surfaces in one setting. Accuracy will be dependent on machine.

@ellastroen 2 жыл бұрын

By installing hub mounting surface only two surfaces need machining . In this case not only 3 surfaces but 4 surfaces must be machined.The outer surface in conduct with the wheel rim is going to run out causing wheel not running true.

@mtay65 2 жыл бұрын

@@ellastroen Agree. Last surface should not be machined with a lathe but a surface grinding machine.

@nextgen1939 3 жыл бұрын

That is not his first time using a 4 jaw. Good set up.

@karlbarrick340 2 жыл бұрын

But why use a 4 jaw for this, it’s just wrong!

@adamjhuber 2 жыл бұрын

If you watch what was done here, this is exactly what you should NOT do.

@daronsteele7976 3 жыл бұрын

That rotor was junk when you started. Now it is dangerous junk.

@maniektoja1234 2 жыл бұрын

0:24 quality control

@dindadacitydindadacity8769 3 жыл бұрын

great work 🎯🎯, everything done right, all three important areas processed in one setting. The very clever ones can try to re-tension the brake disc and align it with the dial gauge ……. good luck ... you don't notice a few tenths of a blow on the contact surface of the rim. Greetings from Germany✌️

@simonpartridge1338 3 жыл бұрын

As someone else has pointed out, there is a minimum width for disks, hence safe practice is to replace pads and discs together. All this is doing is taking the safety margin away from the disc. High chance of disintegration.

@brettymike 3 жыл бұрын

No way will that disc disintegrate.

@bobroberts2371 3 жыл бұрын

Info according to the net As of July 2021, the gross national income per capita in Indonesia is $3,870 . The national highway speed limit is 80-100 km/h (50-62 mph), other roads 40-80 km/h (25-50 mph). So, if you were driving in the city at sub 45 MPH speeds and didn't have $$$, what would you do?

@brettymike 3 жыл бұрын

@@bobroberts2371 Sell body? ;-)

@scootbmx01 2 жыл бұрын

@@bobroberts2371 not drive? No excuse for putting other peoples lives at risk

@bobroberts2371 2 жыл бұрын

@@scootbmx01 Gee, perhaps you live in a wealthy country. Do you really think these rotors are unsafe for 35 MPH city driving?

@user-en4oi4ih5d 2 жыл бұрын

А теперь поставь эти диски на свою машину) это надо делать на оправке я как токарь тебе это говорю с 20 -м стажем

@medodz-ll5iq 3 жыл бұрын

اهيا صاحبي انت عندك الزهر راه فات واحد جزايري من هنا وحطلك لايك حنا راهم يقولك قيسهم وشري وحد خرين جدد حاسبك تخدم الدراهم

@Kabaselefh 2 жыл бұрын

Last week I changed my front brakes set, disk rotors and brake pads .

@efgeebe 3 жыл бұрын

good lathework, but disc is now under size. would not be legal in Australia

@rcdogmanduh4440 3 жыл бұрын

Didn't see him measure thickness but it might be above the minimum thickness allowed! And as they say about the fat girl thats a very big but!

@efgeebe 3 жыл бұрын

@@rcdogmanduh4440 at a quick glance, one side looked thinner than the other too

@Yantoo 3 жыл бұрын

this size still pass the feasibility test in our country.. we did this work for a long time and thanks to god there are no problems.. spare parts are hard to find in our country.. we have to bring in from west country.. sorry my language is bad, I use Google Translate to communicate

@efgeebe 3 жыл бұрын

@@Yantoo I understand. You must do what you can to repair things which are expensive to replace. You did a good job! Saya mengerti. Anda harus melakukan apa yang Anda bisa untuk memperbaiki hal-hal yang mahal untuk diganti. Anda melakukan pekerjaan yang baik!

@humperlumper62 3 жыл бұрын

Why use a 4 jaw, so much easier to use a face plate with a threaded screw to hold the disc against a flat face. Then you only have to machine two faces and your done, plus I bet those discs are undersize with how much was machined off 🙈🙈🙈

@ionutdanielbulai2523 2 жыл бұрын

If is using the face plate him can't do the back side

@CHOIKWANGUK 2 жыл бұрын

@humperlumper62 2 жыл бұрын

@@ionutdanielbulai2523 you can do both faces of the disc easily when the disc is pulled up to the outer face of the smaller dia ….. done it loads of times, plus you’ve guaranteed to be true

@garyboardwine3349 3 жыл бұрын

One sided turns usually vibrate due to uneven pressure on the flange of the disc, also the inside of the hub should be the mounting point of the rotor , and a rubber anti vibration band should be used to prevent vibration, this would work in a last resort , but not the professional way to do it

@MattysWorkshop 3 жыл бұрын

Gday, nice job mate, just like new again, Cheers

@kentuckytrapper780 3 жыл бұрын

This guy does some amazing work with very little to work with.

@wattyler6075 3 жыл бұрын

I just hope you check the minimum thickness after machining?. A friend of mine machined some badly worn discs down & had a piston pop out under breaking.

@janmichaelcatap5994 3 жыл бұрын

yeah that's what I thought too after he machined the rotor. It's too thin to be used the pad and the piston will pop out of the caliper

@Yantoo 3 жыл бұрын

replace the thicker brake pads sir..

@wattyler6075 3 жыл бұрын

@@janmichaelcatap5994 I have done 100's of discs & drums in my 52yrs in engineering working lathes. If it fails afterwards & someone is killed,the machinist can be charged with manslaughter.

@Yantoo 3 жыл бұрын

in my country before use there is a vehicle test and if my job is not safe then we are not allowed to work anymore.. I was taught this kind of work by my teacher, and we have been doing this job for years. Thank God we never had a problem with our work.. maybe this way of working is wrong in western countries.. but in our country Indonesia is allowed

@wattyler6075 3 жыл бұрын

@@Yantoo yes we have MOT tests on vehicles every year here in the UK, but that only tests your brakes reach a certain level of brake efficiency, but not the thickness of the disc.

@antoniorivera5066 3 жыл бұрын

Hay tornos especiales para tornear o rectificar discos y tambores saludos desde 🇲🇽✌️👍

@CiCi-by8dy 3 жыл бұрын

Bang, sebelum mulai, mesinny di bersihkan dl pakai kuas. Lebih bagus klo di video

@konigrollo6267 3 жыл бұрын

@ Mekanik Mesin: Great Job! I know what or means to work without available Spareparts, so You have got my Respect!

@baldrickscunningplan6154 3 жыл бұрын

Would you put these discs on your vehicle? I have had a disc shatter whilst driving and i can tell you it is extremely dangerous and causes a lot of damage. It sheared the brake caliper off the vehicle.

@Zimbiker 2 жыл бұрын

Great job 👍

@eweol127 3 жыл бұрын

Good work. I work with a "MEUSER" lathe and a "CHEVELIER" CNC lathe. What is the brand of your lathe? Greetings from Germany.

@Yantoo 3 жыл бұрын

my lathe brand is CY 6266 sir.

@eweol127 3 жыл бұрын

@@Yantoo Thanks for the answer, have a nice day!

@ThisIsToolman Жыл бұрын

This is what you do if you can’t buy/afford new ones and they may be fine. If they’re under the limit they may warp at which point the problem will be evidenced by a shimmy when braking. Then there’ll be a trip to the salvage yard and the process will begin again.

@pauljames9975 3 жыл бұрын

A disc has a reference face (not diameter) where it locates on the wheel hub. If the minimum thickness is ignored, the pads can be pushed out of the caliper housing and drop on to the road.............then you have no brakes and a disaster. The discs are gripped on the incorrect surface in this video. An accident in the making............

@davidcraemer8227 3 жыл бұрын

He can see how much he is machining off the disc's by the dial indication on the lathe's compound slide and he machined the reference face to match the two surfaces.

@sergiolubrano6191 3 жыл бұрын

Bravo 👍

@douglasberg2881 2 жыл бұрын

There is a reason the brakepads don't go all the way to the edge of the disc, and that is so you can tell it's worn out. Thus you should measure the minimum thickness. Even if the disc still has a couple of millimeters left of wear, it has to be able to make it through the next set of pads without falling below the minimum value. Although breakdiscs are expensive sometimes, they must be replaced. Tires and brakes are still a valuable lifeinsurance.

@rolandolievanoagudelo.5112 3 жыл бұрын

Excelente trabajo maestro.bendiciones.

@snowyseb 3 жыл бұрын

Fantastic, now the disc is undersize 😂

@dave-j-k 3 жыл бұрын

Probably build it up with weld in next video ;) ;)

@michaelbamber4887 3 жыл бұрын

@@dave-j-k ha, yeah. In ribs, so the pads grip better! 🤣

@kryptonian7648 3 жыл бұрын

Yeah it looked below min thick to me too

@destinsmith6966 3 жыл бұрын

And warped!

@Yantoo 3 жыл бұрын

Sorry.. I've been doing this work for decades, in my country this size still passes the feasibility test.. in my country Indonesia there is a vehicle feasibility test held by the government.

@mawandar2145 3 жыл бұрын

Sayang Vlog nya tidak disertai suara utk lebih paham.

@cakgenk4080 3 жыл бұрын

Nyimak terus mas e

@albertogomez1429 2 жыл бұрын

De esa forma de centrado no q bien se coje un plato se pone en el plato bien sujeto en la parte de plato donde se coge los tornillo de le da una y ha esa parte se coge los plato ha tornea y así q bien yo tengo un torno q se monta en el coche copia toda los desviaciones q tenga la mangeta

@alexakos1992 3 жыл бұрын

Excellent job, but the owner need a pair of new rotors

@user-uh6jw7in3c 2 жыл бұрын

Если откинуть остаточную толщину заявленную производителем, то точнее будет точить специальным аппаратом непосредственно на колесе автомобиля. Только такая операция в сервисе не намного дешевле новых дисков

@bkirkbir 2 жыл бұрын

In some countries and depending on the car brand, it changes in huge amount

@user-uj9ie8wy7b 3 жыл бұрын

Просто верх технического прогресса

@vladstankov3492 3 жыл бұрын

Мы скоро так же дудем

@adminuPcu 2 жыл бұрын

Ахахахахаххахахаха, просто оррррр

@ivanhernaez4188 3 жыл бұрын

Seguro q ese disco de freno está fuera de medida, y lo otro ese torno no es para ese trabajo por eso existen torno específicos para rotores de frenos, los cuales toman los rotores del eje de la masa y no por fuera como lo tomó el maestro allí. No digo q el maestro hace mal su trabajo de torno solo q esa pega es para un maestro en Frenos. Con un torno para eso. Saludos

@luisbustamante1938 2 жыл бұрын

Ese disco ya no sirve demasiado delgada la superficie de fricción. Lo rebajaron más allá de lo normal nunca hagan eso!!

@user-fc4ry1cb8w 3 жыл бұрын

ประเทศอะไร ชื่อช่องไร ใครรู้บอกด้วย ขอบคุณครับ

@bkirkbir 2 жыл бұрын

I did this for an e36 bmw and the results was same as a new one.

@tech.automobilemaster.1017 2 жыл бұрын

Good

@amarilisoti 3 жыл бұрын

Now you can drive right

@dusan.racicky 3 жыл бұрын

Disc Rotor Minimum Thickness its irelevant?Does security tell you anything?Such a correction is illegal.

@Yantoo 3 жыл бұрын

@Luminous65 3 жыл бұрын

It is better to put new brake pads on faced disc brake than on old disc, on resurfed disc brake pad can be better lapped than on old surface

@Sam-to1zg 3 жыл бұрын

@@Luminous65 Makes sense

@dusan.racicky 3 жыл бұрын

@@Yantoo BTW:great joob.This correction is also being made here in the EU.But it's not legal and it's not done officially.I also use google translator.

@rogeremberson6464 3 жыл бұрын

I could only watch the first two minutes of the video and my blood started to boil. I was in the motor trade for over 25 years and replaced many brake discs that had worn to their minimum prescribed thickness, some even thinner. Only recently I replaced the front discs and pads on my brother in laws car, a Ford Focus, because the discs were knackered. Then I replaced all four discs and pads on my brothers BMW. Why?, because they were worn the minimum specified limit Finally I replaced the front discs and pads on my sisters Ford Ka because guess what, they were also worn to the limit. At least I can go to bed and sleep easy, knowing that three members of my family can drive their cars on the public roads and stop safely. It's cheaper and safer to buy new discs than to skim a knackered one.

@josiassantoscosta5322 3 жыл бұрын

Uma beleza de trabalho.

@mustafalahrach7696 3 жыл бұрын

معلم.الله.يعطيك.الصحة

@nevermindstylez6299 3 жыл бұрын

Mekanik suuper cool!!!

@ridds777 3 жыл бұрын

Why are you cutting a rotor? Taking away material will only warp it faster.

@ionmanoiu2241 3 жыл бұрын

Comparatorul este mecanic sau electronic ?

@frankthespank 2 жыл бұрын

I use to get rotors turned for $8 a piece. I called around to get the ones on my Mom’s Kia turned, $20 a piece…. $40 to turn a set of rotors now. I bought a new set that was made in the USA for $70.

@richhardchoppers7869 2 жыл бұрын

In my city this kind of work only cost 30K IDR or $2 per rotor 😀. It is cheap as hell. This is a common thing here in our country

@frankthespank 2 жыл бұрын

@@richhardchoppers7869 Exactly, it use to make sense to have your rotors turned if possible, now…. you might as well buy a new set…

@Piccodon 2 жыл бұрын

Indexing worn rotor with a twig! What could go wrong? Rotors are not that expensive, better buy a new ones. Rotor thickness is no joke. Why use a 4 jaw lathe chuck for a round object? It makes it harder to adjust. 3rd world technology.

@technicalideaindwarka8040 3 жыл бұрын

Very nice work #technicalideaindwarka

@pauljanssen2624 3 жыл бұрын

Minimum thickness what's that and that's equal on both sides not one side being thicker and the other side being paper thin

@UssGo 2 жыл бұрын

Just buy new ones?

@adminuPcu 2 жыл бұрын

ЕСТЬ ТУТ КАЧЕСТВЕННЫЕ СТАНОЧНИКИ КОТОРЫЕ ВКУРСЕ, ЧТО ОН ДЕЛАЕТ И КАК?))))

@user-ez5sl4zh4b 2 жыл бұрын

По выроботоной поверхности нельзя выстовлять детали поверхность выработки неровная

@badoldbiker368 3 жыл бұрын

Hei mas pekerjaan bagus lainnya. Tetap aman.

@Yantoo 3 жыл бұрын

Terimakasih mas.. Salam hangat dari Indonesia

@jobspeedmms 2 жыл бұрын

amazing...👍🏿

@sohasteelsenginering1590 2 жыл бұрын

👏👏👏👏👏👏👏

@Darndiddlyarn 3 жыл бұрын

I guess minimum thickness must be about as important as hunan life if that country.

@vicrally007 3 жыл бұрын

А теперь и в чермет не стыдно сдать

@peeyem6029 2 жыл бұрын

Lathe ൽ പണി അറിയാവുന്ന വർക്ക് ഇതെന്നും വലിയ Job ആണെന്ന് പറയത്തില്ല. ഇതിലും എത്രയോ പ്രയാസം നിറഞ്ഞ Job ഉണ്ട്. അങ്ങനെ വച്ചു നോക്കുമ്പോൾ ഇത്. എത്രയോ നിസാരം Lathe കണ്ടിട്ട് ഇല്ലാത്തവർക്ക് ഇത് വലിയ സംഭവം ആണെന്നു തോന്നും എന്റെ സഹോദര വേറേ വല്ലതും ഉണ്ടങ്കിൽ കാണിക്ക് ഇത് Automobile work ൽ ഏറ്റവും Simple'

@romandhon2878 3 жыл бұрын

Terima kasih sebelumnya,,Mas,mau tanya,, mata bubutnya pakai merk ,atau tipe apa ,,agar bisa kuat tajam🙏🙏,,

@Yantoo 3 жыл бұрын

Merk yg6 pak.. Cara buatnya ada d video saya juga pak

@jayadiwibowo3598 3 жыл бұрын

@@Yantoo Maksudnya merek yg 6 mana bg.???

@WattsGemini323 2 жыл бұрын

If the cut takes the rotor below spec it isnt a safe rotor

@kp-qr6hy 3 жыл бұрын

Using a uncritical eye this looks good , unfortunately it appears he has got this all wrong, instead of trueing the disk face, when setting up the disc, He should have trued the mounting face ,where the disc is clamped to the hub with the wheel nuts ,then trued the disc faces to the mounting face , unless we he's very lucky the brake pedel will pulse

@bobroberts2371 3 жыл бұрын

He made the back side of the hub mounting face paralell to the rotor wear surfaces and did both wear surfaces in the same chuck setup. Sure, a brake rotor lathe would be better but in a low income country, you do what you have to to get by. ( As of July 2021, the gross national income per capita in Indonesia is $3,870 )

@ryanhagler9410 3 жыл бұрын

I would love for ABomb to see the indicator

@Yantoo 3 жыл бұрын

😁🙏

@kentuckytrapper780 3 жыл бұрын

Great job man, amazing.

@stevejobs1653 3 жыл бұрын

Отпескоструят и продадут как новые!

@z_brzuszkiem_w_gory 2 жыл бұрын

Tarcze na złom , ciężkie jak tarcze do szlifierki. Chujnia , za 5 tys km na złom

@danielmoore3467 3 жыл бұрын

If it is straight it won’t be the first time you hit the break pedal

@rogerfontenot2610 2 жыл бұрын

My condolences to the driver that uses that break disc

@oldfucker68 3 жыл бұрын

It's cheaper to just buy new rotors.

@richhardchoppers7869 2 жыл бұрын

It is cost only $2 max $3. New rotor $100-$200. Huge diff 😀

@oldfucker68 2 жыл бұрын

@@richhardchoppers7869 ok so what do you do when the rotor is out of spec and cant be turned? Like I said it's better to buy new rotors.

@richhardchoppers7869 2 жыл бұрын

@@oldfucker68 'IF' it is still in spec re-use it, re-turned it, re-use it again, re-turned it again untill out of spec "Out of spec" then buy new one and REPEAT above process again and again

@anicassiopereira8175 3 жыл бұрын

Não é dessa forma que se prende o disco

@Yantoo 3 жыл бұрын

esse tamanho ainda passa no teste de viabilidade em nosso país .. nós fizemos esse trabalho por muito tempo e graças a Deus não houve problema .. peças de reposição são difíceis de encontrar em nosso país .. temos que trazer de países ocidentais. . desculpe, meu idioma é ruim, eu uso o Google Tradutor para me comunicar

@masporque1588 3 жыл бұрын

Anicassio, concordo que não é o melhor dos processos, mas observe que ele da um passe no fundo, onde e a referencia, da uma corrigida, nao menos este processo de torno não é o melhor também, isso diminui a vida da pastilha, o correto é retificando com o rebolo sem deixar marcas, mas é o que temos para hoje. Vamos entender, sequer relógio comparador ele tem.

@user-pv1nl6ng6i 3 жыл бұрын

человеческая жизнь уже стоить дешевле тормозного диска....

@RrRr-th1kf 2 жыл бұрын

Brake disk need to change because thickness is very thin

@teamidris 3 жыл бұрын

The last two I did I skimmed the hub faces. They were so rusty it really helped get a datum. I like the back-tool.

@Freedomua-jw2vf 2 жыл бұрын

Можна викидати на металолом. Проточка на трьох площинах обовязкова!

@letcikigor 2 жыл бұрын

👍

@andisetiyawan1363 3 жыл бұрын

Beli dial bang,

@user-im7qo6ev5x 2 жыл бұрын

А четвертую плоскость кто делать будет? Незаверенная работа.

@jessman1004 2 жыл бұрын

NO WAY !!

@christopherleather9262 3 жыл бұрын

We could even take the outer rim of the disc🤔

@bartekino 2 жыл бұрын

WE Need holes in there for more performance.

@garyboardwine3349 2 жыл бұрын

Perfect example on just because it's on u tube doesn't mean it's the correct way to do things

@Ryan-lc9ij 3 жыл бұрын

Why even bother, thickness is reduced and for the cost buy new, disc will mostly shatter!

@liyosateknik4571 3 жыл бұрын

Mohon maaf mas, bukannya menggurui, lebih baik sebelum mulai, mesin bubut nya di bersihkan dulu mas, gram di eretan nya itu. Biar lebih bagus dan rapih mas. Terimakasih

@MichaelSanchez76 2 жыл бұрын

Was ist mit dem Mindestmaß? Heutzutage ist sowieso gerade mal das nötigste an Material drauf...

@pavolpotrok12 2 жыл бұрын

Perfectily

@christophermenus2276 3 жыл бұрын

le comparateur du pauvre mdr xD sinon pas mal

@thomaskruger6468 3 жыл бұрын

Hallo ! Altes MAN Prinzip: "Hauptsache blank , dass Maß ist nicht wichtig " ! Wie wird ein Werkstück ausgerichtet ? Ohne eine Uhr ohne irgendetwas in diesem Fall 😂🙈👀🇩🇪🙏❣

@konigrollo6267 3 жыл бұрын

Der Typ sitzt irgendwo in Pakistan oder Paraguay, da muß man nehmen was man kriegt. Was bei uns billiges Verschleißteil ist, muß man dort eben irgendwie aufarbeiten, gefüllte Regale mit Neuteilen wie bei uns ist für die das Schlaraffenland. Gemessen an den zur Verfügung stehenden Mitteln ist das im Video eigentlich eine Meisterleistung...

@andizx8113 3 жыл бұрын

Using a dial gauge is overrated anyway

@xy2713 2 жыл бұрын

das problem ist die felge läuft jetzt plan vielleicht nicht mehr

@user-ub7fv2co5i 2 жыл бұрын

Вот так старые диски превращаются в новые!

@adminuPcu 2 жыл бұрын

видимо ты такой же делитант как и он, таким макаром выверки биения по трущейся по верхности, можно вообще лишится тормозов, а точнее их эффективности!

@Yantoo 2 жыл бұрын

десятилетиями этот метод используется в нашей стране Индонезия. а в других странах это еще полемика .. каждый мелкий ущерб заменяется новым, тогда вы только станете настоящим потребителем

@adminuPcu 2 жыл бұрын

@@Yantoo ВООБЩЕ ПОБОКУ ЧТО У ВАС ТАМ, ПЛОХО ТО, ЧТО ЭТО РПЗРЕШЕНО В НАШЕЙ СТРАНЕ, ТАКИХ РУКОЖОПОВ КАК ВЫ, ВЫ ГЛАВНОЕ ДЕЛАЙТЕ БОЛЬШЕ ТАКОЙ РАБОТЫ, А МЫ ПОСЛЕ БУДЕМ СМОТРЕТЬ АВАРИИ НА ВАШИХ ИЗВИЛИСТЫХ ДОРОГАХ! 👍)))))))

@michelemasters280 3 жыл бұрын

Spinning to fast for cast iron

@tarekelsayed7431 3 жыл бұрын

أسوأ ماتفعله باظةالطنبوره بسبب هذا التخلف على سرعه عاليه يحدث رفه للطنبوره وبالتالي العجل الامامى فكره متخلفه كذلك جسم الطنبوره ضعف من الخرط دوسة فرامل قويه تنكسر وتدخل فى مشكله رهيبه قلب العربيه