Repairing The Handles On A Vintage 1983 Case (Ep. #19)

Рет қаралды 416

16 күн бұрын

Follow along as I rework the bone jigging on a vintage Case Whittler (6308) that I found at an antique shop.
#case #casexx #pocketknife #bone #edc #vintage #antique

Пікірлер: 25

@phillipw58 14 күн бұрын

Great job! Really cool knife!

@AWCustomDesigns 14 күн бұрын

I really appreciate you man!

@Pocket_EDC 15 күн бұрын

Now that was an excellent job, man. And a really well detailed video. I'll be adding that to my library of techniques. Thank you. Cheers.

@AWCustomDesigns 15 күн бұрын

Thank you! It was about a 32 minute recording to start with, so I tried to make it bearable to watch

@rwa123 14 күн бұрын

Excellent job! Well done. Looks great! 👍👍 Love the background music! 🎵 Happy Monday! Cheers, RW

@AWCustomDesigns 14 күн бұрын

Thank you! Cheers buddy 🍻

@tedhart7708 15 күн бұрын

Excellent video, and the jigging turned out great!

@AWCustomDesigns 15 күн бұрын

Thank you brother! It’s definitely not perfect, but I think it blends in pretty well

@865knives 10 күн бұрын

Nice work man! I’m going to remember this for future reference and repairs! Thanks man

@AWCustomDesigns 10 күн бұрын

Thank you buddy!!

@RandysWSG 14 күн бұрын

Awesome job on this!!

@AWCustomDesigns 14 күн бұрын

Thank you so much Randy!

@R.H.bladeNshade 14 күн бұрын

Dude this was pretty cool!! I think it really did turn out great. Awesome work brother!!👊🏼

@AWCustomDesigns 14 күн бұрын

Thanks so much man! I think it blends pretty well

@ufoyz250 14 күн бұрын

Great work!

@AWCustomDesigns 14 күн бұрын

Thanks dad!

@cynthiajeffrey 10 күн бұрын

Excellent job! I think if you didn’t know that it was repaired you wouldn’t know. Once you get that shield in there it will look original.

@AWCustomDesigns 10 күн бұрын

I really hope so! It’s a great little knife, just needed some love

@cheesymoonworkshop 15 күн бұрын

Nice job!

@AWCustomDesigns 15 күн бұрын

Thank you! 🙏

@williamwest5827 15 күн бұрын

What I’ve done on a few knives missing the emblem was to use an end casing of a shell I’ve fired like a 357. I cut off the brass end leaving just the rim to an end fitting flush, slightly less than the bone/scale. Scribe or mark the scale side with the missing emblem and rout out the space for the new emblem. Glue the replacement in with your favorite glue, super glue, gorilla glue, or 2 part epoxy. It’s always tough finding a replacement emblem to match the original. However, a nice looking mod will garner some nice comments for us knife enthusiasts. Either way, you can’t go wrong, especially on just a pocket carrier.

@williamwest5827 15 күн бұрын

PS: Nice work! Thanks for the lesson.

@AWCustomDesigns 15 күн бұрын

I did think about that, I love a knife with a cool bullet casing as a shield. I also toyed with just continuing the jig over the shield hole. But then someone told me that you can send the year and model info to Case and they will provide you with a replacement shield. So I figured I would try that route first before I went too far with it. Thanks for suggestions and the comments buddy! 👍🏼