Left the poly and installed a rubber boot for no reason and cut more out for an access panel. Cut it shorter and then install trim around it so you don't have an access panel
@chrisviolette89919 ай бұрын
The id of those pex fittings is 3/8th of an inch. Laundry should get 3/4" pipe.
@dragon03618 ай бұрын
Its fine bro.
@daddysullivan877 ай бұрын
Your knowledge is impeccable
@JackTheAwesomeKnot7 ай бұрын
Wtf, since when does laundry need 3/4? 😂
@stich1960 Жыл бұрын
What is the purpose of using the rubber connector rather than a cheaper PVC coupling?
@Jetx17 Жыл бұрын
Probably to make maintenance in the future easier. Don’t have to make any cuts.
@stich1960 Жыл бұрын
@@Jetx17 shouldn't really be a maintenance item though
@noahclark802 Жыл бұрын
Bro no need for that no Hub ban Put your pex adapters on first lol
@8thyearApprentice9 ай бұрын
Why the fuck did he use the no hub....lol
@Staysobereveryday8 ай бұрын
That’s the same thing I’m asking , probably all he had to work with, I just wish they could make videos showing it done the right way
@Cortinas28 Жыл бұрын
This was beautiful to watch
@ernestoflores3168 Жыл бұрын
Beautiful work 👏 I wish I knew how 🤔
@Devin-_- Жыл бұрын
He just showed you
@waltermitchell2359 Жыл бұрын
Make sure you tighten the hub unless I missed something
@theconservativeplumber Жыл бұрын
It wasn’t shown but if you pay close enough attention you can tell that it gotten tightened.. look right after I wipe the fittings with the rag
@owentimo9 ай бұрын
Why do you use the rubber hub connector? Can i use a ABS coupler. Which is better?
@ntgbuilds Жыл бұрын
That polybutylene pipe is going to be an issue again
@theconservativeplumber Жыл бұрын
Yes
@luisvalencia8048 ай бұрын
Ya could of glued a coupling at least
@adrianadrian23914 ай бұрын
Nerozumiem prečo odrezal kanalizačnú rúru?a prečo nenamontoval také isté ventily?
@bludika7 ай бұрын
i never understood why they made these laundry boxes just one time use only, with NO access to the piping below the valves. Sooner or later they will eventually need to be replaced, and 99% of the time, you gotta cut the drywall, but why make it that way? wouldn't it better if the laundry valve box was a bit bigger down below so you get about 5-6 inches of piping below? i hate how you gotta cut the drywall every time when replacing the valves first time
@CP-up8qz Жыл бұрын
The gray Pex of death
@timothyunterthiner2637 Жыл бұрын
That grey pipe is poly butelyne and it’s No longer sold or supported.
@mardighakimian5472 Жыл бұрын
Good job
@CHMichael Жыл бұрын
Could have dropped the box a little and not needed to ad length ( I'm not a plumber)
@theconservativeplumber Жыл бұрын
Not without doing drywall repair.. so I couldn’t have if I wanted to do what my customer wanted done
@jpmotovlogs9968 ай бұрын
I never touch poly. Replacement. I get it some customers don’t have the money. But as soon as it leaks guess who’s getting the blame
@Anthony_Spilotro7 ай бұрын
All of this could've been avoided with a couple quick shots of flexseal.
@christopherlane69yo8 ай бұрын
I don't have a problem with any of it except the blue glue lmao
@timothykelly2825 Жыл бұрын
Is that short of a pex piece going to cause issues? Any experience using short pieces like that?
@MisterTwister889 ай бұрын
Short pieces can burn the house down
@Rsdemo22768 ай бұрын
More plz
@view26117 ай бұрын
Oh man you so fast I never see a plumber like you
@espinoza71667 ай бұрын
I watched your videos your better then ask this old house so I said I’m going change my faucet 3 hours later😂 turns out you need a special tool and it was long swivel type of tool.
@danielbudzowski57747 ай бұрын
Everything bothers me in this
@giantgrowth4204 Жыл бұрын
Are you using rain or shine lol
@JoshuaEssary Жыл бұрын
The most helpful video I've seen today
@vinniegugger33178 ай бұрын
Those threads weren't npt That was a sweat box 😳
@Seven7Pain1 Жыл бұрын
Good job but the blue glue just put little purple primer in the glue can if you need to see it ,
@ScottyLiardi7 ай бұрын
Most of you have prob never turned a screw driver a day in your life.. All these haters pointing out everything they think is wrong, is what keeps us tradesmen in business. They watch a ten second video, think they can do it themselves, and then call us when they flood their house. 😅 Please... Keep on hating... We'll take your money any day of the week. Preferably after hours, and on a Sunday. That way we can really dig into those "know it all" pockets that you wear so poorly.
@leakyfaucet1239 ай бұрын
As a fellow plumber, I don’t get why everyone who isn’t brave enough to post their work goes ripping other peoples work. We all do things slightly differently. 😊
@mr.dahliaking.202 Жыл бұрын
To this day its so alienating and ridiculous for me as a European how Americans use hot and cold water for their washing machines, because its so weird for me that on US WM does not have their own heating element inside like washers elsewhere in the world have. You just hook the thing onto cold water and the thing heats its own water. What does American do if their boiler is broken and they dont have hot water? Is their washing machine doesnt work then? Its so weird for me.
@daltonmarth Жыл бұрын
I dont think I wash anything I own I with hot water so why pay more for a washer with a heating element built in?
@mr.dahliaking.202 Жыл бұрын
@@daltonmarth well perfect example are bed sheets. If you are a heavy sweater like me if i dont wash my sheets at 95'c the bacteria survives and it starts to stink after one night. And also i have a cat and sometimes she has an accident on chshions or pillows and if you ever had a cat you know cat pee does not wash out that easily only in boiling water so that too.
@iwenive3390 Жыл бұрын
Walk over to Home Depot and buy one cheap
@chester6343 Жыл бұрын
@@mr.dahliaking.202 bruh my cat pisses on my pillow it's 1000% going in the trash, jesus christ
@mr.dahliaking.202 Жыл бұрын
@@chester6343 its not a bid deal. Its the smell that is ugly. I wash it in 95'c and its fresh like new
@robertwodnicki55978 ай бұрын
Amateur
@louietheplumber3609 Жыл бұрын
Clearly not a plumber
@phil0083 Жыл бұрын
Get an oscillating tool dude and stop butchering sheetrock edges.
@user-lr5bo3ip8i11 ай бұрын
Bro you know they make a washer box for pex? No need to screw on a female fitting
@MisterTwister889 ай бұрын
If you keep only one type on the truck, it should be thread/sweat connections like this one. Not every house has Pex waterlines
@boostmobile2747 Жыл бұрын
Access panel hmmm I guess you don't know how to patch is ok my amigo call Jose. Good thing you got away with that much faster easier ,my experience they make us patch it pain in the ass
@charlieb9502 Жыл бұрын
sure but that's quest pipe. you are now going to have leaks below those joints.
@theconservativeplumber Жыл бұрын
You paying for a full repipe? Send me your billing info and we’ll get started.
@33392.9 ай бұрын
You didn’t have to do all that all you had to do is replace the hose bibs