Replacing Quiet Fans In Switch

No video

Replacing Quiet Fans In Switch

Рет қаралды 9,805

Күн бұрын

I wanted to use my Aruba S2500 switch, but the original fans are very loud, so I got some Noctua fans and put them in to make it much quieter.

Пікірлер: 35

@TallPaulTech Жыл бұрын

"Why didn't you do this?", "Why didn't you do that?"... Why don't go you and fuck yourselves, huh?... how about that?

@Berryservices Жыл бұрын

Because everyone thinks they are an expert in all fields these days. I enjoyed the video Paul thanks!

@Akshun82 Жыл бұрын

I'm a *big fan* of this mod

@giga-chicken 6 күн бұрын

For the record you can usually just carve the alignment key off a 3-pin fan header (dremel, file, knife, even sandpaper will do) on the yellow side and plug it into a 4 pin socket. No rewiring needed.

@ericturner2477 7 ай бұрын

I just did this to an old HP 5120 switch I have. It reduced the noise from 65 dB to 35 dB, a huge difference.

@tamasstrezi Жыл бұрын

The plug which came with the fans would have just slotted onto the first three pins of the boards headers. Fourth pin is optional

@MrDukeLeto Жыл бұрын

Hi Paul! Greetings from Khabarovsk! I did the same procedure on various cisco devices. But I didn't cut any wires, just move some pins in right positions, just like you in the end of the video.

@MikeKirkpatrick Жыл бұрын

Nice job. There is a PWM version of this fan that has the 4 pin connector out of the box. I found out the hard way by ordering 2 PWMs when. I need the FLX for my TP-Link switch.

@TallPaulTech Жыл бұрын

That's what I thought I was getting, but apparently not

@pmf026 Жыл бұрын

Why didn't you use included anti-vibration rubber thingies instead of the screws (and drilling, and metal debris inside the case, etc.)?

@RoryIsNotACabbage Жыл бұрын

Like most homelab projects, "Didn't think of that at the time, but it works so fuck it" He did at least blow out the metal debris, I recon it will be perfectly good

@drcpaintball Жыл бұрын

Because the grey case that goes over them shears them off, genius. I tried.

@mitchellslot Жыл бұрын

Why not use the 40mm PWM fans from noctua? Then you don't need to transfer the wires

@TallPaulTech Жыл бұрын

I thought the ones I ordered were the matching ones, but turned out they weren't. Either way, they can run at full speed all the time since they're quiet enough.

@wellingtonfreirerosa 9 ай бұрын

@@TallPaulTech but it has a much lower CFM too, monitor the temperature, as you may have a cooling deficiency. A normal fan has an average of 15CFM, the Noctua has 5.5CFM

@alonzosmith6189 Жыл бұрын

Nice, looking to replace the fans in my Ruijie Reyee switches

@drcpaintball Жыл бұрын

Thanks for showing pinouts, other videos omit that part

@TheNitroG1 5 ай бұрын

because you don't need to rewire them. They will go over the existing 4 pin port and you just won't have speed control it will run full speed all the time.

@christopherdoyle8081 7 ай бұрын

Does this mod even have the same air pressure as the older fans? Was there a baseline of this switch at 100% load?

@benjaminl1173 Жыл бұрын

old scotchlocks to the rescue

@farktard2740 Жыл бұрын

scotchies!

@elemental3076 Жыл бұрын

Oh no, why u didn't just unclip pins from old fan plastic connector and clip back from new one

@0ChAnTi Жыл бұрын

Hi Paul, hope to see updates if your mod is stable even in full sommer time. In what kind of highest ambient temperature you expect for the switch to work? I am hitting 104°F /40°C here and it got very noisy. Hope to see more of your content. Take care

@TradieTrev Жыл бұрын

Trev wants to see more electronics hackery! She's pretty rough using scotch locks, lol. Good enough for Australia as Dave Jones says.

@TallPaulTech Жыл бұрын

I might just have to do that

@RoryIsNotACabbage Жыл бұрын

If you had poked the holes in the first place you could likely have changed the head without connecting any cables. Should work just as well like this but worth noting for the future

@TallPaulTech Жыл бұрын

KZfaq is getting worse. That comment of yours was in the 'held for review' because it was apparently bad or nasty or some shit. It baffles me how so much soy got to be in charge of so much these days.