Love this way better than shorts chris!

The longer, the better. Thanks for this video Chris. I need to reseal my headlights and I always enjoy learning new tips and tricks from you.

I did watch the whole video and wish there was a service just for headlights in the UK. I will have to tackle this myself but this video guide is invaluable. Thank you!

I watched the whole thing, Chris. GREAT, informative video with lil nuggets of info that most people don't know!! Thank you for sharing and teaching us!!

I watched the whole thing and thank you for putting in the time to show how this is properly done!

Much better then the shorts! Lots of info and detail. Keep up the good work Chris!

Watched the whole thing. Greatjob especially the finishing work of smoothing haven't seen anyone do that before.

I watch the complete video, much better than the short videos. I love all of the details that you have added.

Hey Chris, I wanted to thank you a ton for making this video/sharing your knowledge! I've done a few sets of headlights over the years, and previously used silicone to reseal. I used this RetroRubber for the first time on my 370Z headlights, based on your recommendation from this video. Lets just say the headlights couldn't condensate if I wanted them to 🤣

I watched the whole thing and will use the same products that you used to rebuild a headlight for my 2002 Audi TT Roadster. Thanks for all the tips!

I watched the whole thing! I just picked up my e60 550i and will be separating my first set of lenses. I’ll be wearing my FlyRyde hoodie hoping to transfer some of your Jedi headlight upgrading powers. Wish me luck.

Here’s a video idea, you mentioned leaky headlights. Why not make a video on how you personally deal with leaky lights, such as steps on how to find a leak, how to repair a leak, different kinds of leaks ie standing water or fog or just droplets.. Or when it’s time to give up on a set that’s not fixable. Side note, this is the best tutorial I’ve seen on dealing lights. Love your vids!

Thanks for this comprehensive video. Doing my first reseal and your advice is gold. Retro rubber is definitely the way to go. It doesn't feel exactly like run of the mill butyl rubber sealant. The formulation must be a little bit different. It feels like the softening temp is a bit higher than regular butyl. And also holds its shape a little more at the same temp.

Thanks, watched the whole thing btw, I was trying to see how to open the assembly then I realized the glue and wasn't sure how to go about it, great stuff!

I watched the whole thing ! I am planning on customizing my headlights soon. I am starting small with my fog lights now

Excellent, I've just taken apart an Audi TT headlight and was wondering what to use to reassemble it👍

Thank you for this exact video. I got an Set of R35 GTR headlights coming in for an reseal. I know the earlier models have an common problem where they tend to leak.

Yeah much better than the shorts. I don’t even mess with lights but always enjoy watching your vids. 👍🏼

Thanks a lot for the videos, man. I will have to reseal my headlights son, so I watched a lot of times the video about opening them, and this just became the cerry on top. Maybe I'd start a little business here because no one offers thins kind of service here in Chile. Thanks again and have a great day, mate!

I watched the whole thing! I loved it, you were entertaining and you know your stuff!

"I watched the whole thing". Educational as always, Chris. Thanks

Watched the whole thing! I’d love to see more videos sealing taillights that were cut open

Love the longer videos. I watched the whole thing.

Longer videos are definitely better for me, but i thing everyone learns in different ways! just keep doing what your doing, because your doing great :-)

Thank you for your time, I watched the whole thing and learned a lot...

I watched the whole thing!! :) Really useful - I'll be splitting my headlights down soon (I'm in the UK and the car is a Japanese import so I can't easily find replacements!!!) and resealing them was a big concern of mine... great information - liking the little sachet of Silica in there to catch any moisture which may occur.... Excellent work :)

Thank you for showing us how it's done with all your previous mistakes included🙏🏼 baking my lexus headlights ballast and all! Great point about the xomponents being totally rated for these Temps haha. Some people spend hours tearing down prior to heat. So many good tips and tricks here! Like and sub

Very informative and I definitely watched the entire video, thanks for the advice.

Watched to the end and learned a few things, definitely what I was after 🤙🏽🤙🏽

Watched the full video. Very informative. Thank you.

"I watched the all thing" 😃, always great to learn, thank you.

Dude I watched the whole thing! I really wanna see a video of you using a hot melt gun or machine to seal up headlights. I need to seal up old school 7” glass sealed beams and there is no way I can use rolls of butyl. Really interested in: 1. The best machine to use 2. Whether I can use a hand held gun 3. Whether I need to find butyl glue sticks or can use ‘bricks’ of glue 4. The thickness of the melted glue and how fast it flows and how easy it is to control Thanks Chris!!

The long videos are better gives me confidence to do this to my lights

GREAT video. The more detailed the better! Thanks!

Watched the entire video, thanx for the input

I don't know if this guy is making videos anymore, but follow his advice. I just retrofitted some HIDs into my mustang because I couldn't see shit at night and his content really helped me figure out the process as I had never done a project like that before. One piece of advice I have for anyone attempting this is DONT USE PINE 2x4s in the oven. They get hot and leak sap out and them you have to scrub it out. Ask me how I know lol. It does make your kitchen smell really nice tho

I watched it all. Pretty helpful stuff!

In Dubai on a normal summer day the temps in a parked car will exceed 200 degrees. When running, the headlights will reach temps over 400 degrees and that's totally fine

You should go over sealing wires coming out of a housing. Like halo wires if u don't have rubber boots on your factory lights.

Страхотна работа. Браво. Благодаря.

awesome vid man I watched the whole video love these better then your shorts :)

I watched the hold thing 👍👍💚💚💚great refresher💚💚💯

Watched the whole thing. Thanks

Watched the whole vid, nice tip with the soapy water ! 👍🏼

Great video, im doing my 1st ones, thank you!

Hey am from Jamaica and I have my headlight to seal back up again, the first time I did use Eurotain

220F is 104.4C for those who don't measure in freedom units

Love the video Thanks. Do you know of a suppier for head light lenses? I've got a 2014 Acura MDX and need a new lens. THanks again for great content.

Very helpful, thanks

So the way I do my process Chris is I put the rubber in cold. Run it along the channel. Heat it up with a heat gun. The I get a old flat head Screwdriver and smooth it out and push it in the channel if I have to. Install the lense and heat up in the oven after and clamp it down

Very interesting and informative good watch

Great video!

I watched the whole video because I’m about to reseal mine. The soapy hands to work with the sealant was a great idea. Do you always place the sealant on the outer edge. Or you only do that for certain headlights like the GTR?

Very good Video thanks.

I watched the whole thing!!

Would u recommend this for tail lights that are heat welded, tail lights you have to use a dremel to cut open. This seems easier to work with than J-B weld.

Advice needed. My custom headlights keep missing up bad. 3 times now I have taken them off, heated up and with a vacume cleaner inserted to suck out the moisture. Yet they still mist up badly. I can't see any holes or damage that's letting water in either. What do you suggest? I did think what about blasting them in an oven on a low temp to hopefully get them bone dry? But what temperature and time

Great Content

Love the vid, of course I watched and liked it

Might be a silly question but how come we can heat headlights up to open them and not do the same with tail lights? Everywhere I look, you are instructed to cut the tail lights open. TY

Silicone is not the fast way. But cheap, easy and reliable. It needs week or two to harden and stop excluding vinegar. I used the cheapest sanitary silicone and not hard version for sealing aquariums because i want the option to disassemble it. 2 years no leak, car stayed outside and used daily. But i completely cleaned lenses and plastic back from old butyl sealant. I tried to use butylalwaysstickymess from tube but it was too hard to press lens enough deep into plastic back of light. Butyl from tape like on this video is version which is easy to disassemble, but hard to seal properly. Small mistake = leakage. After 2 or more years i removed headlights because i switched a car and i wanted to know state of morimoto mini copy lights i used to modify the headlights. I was able to open silicone sealed headlights but i do not remeber how, maybe patience. It is more than 8 years so i do not remember exactly. I modified headlights in 2011 or 2012. I used morimoto mini h1 copycat modified for H1 halogen bulb. Not good for minis, they do not like about twice as much heat, so aluminium surface was started to peeling off and plastic holder of lens had broken one leg. But i liked light output.

I watched the whole thing!!!

Can I use heat gun instead of oven to apply the seal and opening the lens

I just bought a set of Mopar OEM headlights for my 2011 truck and I want to make DAMN sure they never leak like the originals did (after about 8 years). Can I apply that retro rubber without taking them apart and without putting them in the oven? Or is there a butyl rubber caulk that I can just run a bead around the edge for extra protection?

Detailed videos, just like this one is perfect, since your wondering. That’s my opinion..

Hey, I am just trying to redo the reflective surface of the headlight bowl. I have an old 1995 Sidekick that water got in and (water/moister...you get it) it oxidized, so the headlights are non existent when they are on! Is there a paint that I can use to restore them or do I need to send them off somewhere to have it repaired?

Dude, I literally watched the whole thing. It was actually therapeutic to see the process and see and hear about the little "what if" scenarios happening while doing it... also, the solid advice for why ppl shouldn't cheap out and rush through it...(bc you already there will be those ppl..lol) love it bro! Keep up the good work!

Can you do a video of ways to run and seal wires that are added.

What about if you don’t have an oven? Kitchen oven works also? Would I damage the kitchen oven with the lamps?

Have you ever opened up a set of Audi TTs mk2 xenon headlights?

Question. What are preheating procedures for the rubber?

I watched the whole thing have you tried a product called, The right stuff? How did it work for you?

Ballasts get hot as fire too. Is it a waste of time that I clean all the old butle out of the channel before putting new in?

Should the old sealant be removed if your adding new?

Hey, loved seeing the whole process of sealing the headlights. I might have missed it, but did you add the screws to the headlight at 19:15 or the headlight came like that. Might be a stupid question, but mine had only butyl tape, no screws on the outisde.

What about Urethane windshield silicone will it work

Have you done a 2012 Acura Tl headlights?

Hey question Is Diode Dynamics headlight butyl also good? 🙏

id love to team up and make a set of customized headlights and tailight s for my 09 prius to make it something special... or where could i get some of those electronics so i can diy? thanks a ton, -peter joseph

What kind of oven is that? I've been thinking about offering a reseal service to my customers since new lights on many vehicles are over a grand. I can make plenty of GP and save them a ton of coin.

How do you clean projector lenses? I spent most of the time getting lenses clean, and still couldn’t get them perfectly clean.

For whatever it's worth, I work in automotive field as mech engineer and the IATF 16949 standard have temperature range -40°C to +125°C (-40 to 257 F) so material typically made to withstand that, being electronics/mechanics/paint, what have you...

¿ How long does it take to dry the glue headlamps?

So, Quick clamps and not the rubber surgical tubing?

Like long video and can you do 2015 Nissan Altima headlights

I watched the whole thing.. I much prefer these to the shorts.

Love this kind of video. I made my FIRST mistake on my FIRST set of taillights! I didn’t heat up the retro rubber and I, for some reason, put the light in AT 240 DEGREES 🤦‍♂️ for almost as long as I did when I pulled them apart! 🤦‍♂️ silly me but I’m learning… @krimsinxprojects

I watched it all

Do you do this for other people? I can send you my unit from my Solstice GXP?

I can't stand the shorts. This video is worlds better, and I'd rather watch a video like this with some ads than a short with no ads Watched the whole thing!

I watched the whole thing

Cover to cover. Thanks!

How long ur supposed to leave the butyl in the oven for?.

Watch all off it ty

I’m confused. If I put the headlight in a preheated oven, the headlight heats up. If I put it in a cold oven and turn on the oven to 220, both the oven and headlight heat up together. Seems like it would actually be less thermal shock to heat both oven and light together. I just opened up my headlights that way the other day, heating them up from a cold oven, had no issues.

In all my years of driving 55years and owning 60cars i have never come across a lens that needed tobe resealed ever!!! And the chances of this ever happening must run into millions 2 one!!!🤔🤪

Hom much mm Rubber? Thanks

This video is amazing. Why don't you make new videos? :(

I watched the whole thing. I have a big question for you. I bought some custom headlights from this company call CW customs and I think they did a terrible job sealing it. As well as I don’t trust this guy or his craftsmanship so it makes me hesitate on paying to have the headlights installed just for them to shit out on me. Would it be possible to send them to you to look it over?

"I watched the whole thing"