Restoration of Very TIRED and Rusty 100 Year's Old AXE

Рет қаралды 44,255

SkillFullisM

4 ай бұрын

Hello. In this video I restored Old Rusty Broken Axe.

Пікірлер: 18

@user-tl5hg8kj2o 2 ай бұрын

Beautiful restauration profissional

@vinceianni4026 4 ай бұрын

Beautiful restoration mister beautifully restored

@simonontong7539 3 ай бұрын

Beautiful restoration

@user-us7vz9ys5e 3 ай бұрын

NICELY DONE!!!

@julienghanadan8311 4 ай бұрын

Great job on restoration of very tired and rusty 100 year’s old axe skillfullism 🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰

@jameselliottlinnell7869 4 ай бұрын

As an industrial blacksmith for many years, the axe head would go in the forge to knock out the old handle and while white hot I would re shape the handle hole with my pre formed axe head punches then reheat to draw out the blade on the power hammer once forge work was done bury the axe head in the coal ashes to normalise the steel to return it to its original state , then when cold cut and grind the sharp end grinding across the blade not vertical to the blade, if the joint needed welding this would be done while the axe head was dull red heat with a high tensile rod and not ground off to keep the strength of the weld then normal use . The handles were supplied by a local company and fitted to the customers requirements long or short, the wedge slit was pre cut and after at least a day in water we used a hard wood wedge and made two small steel wedges to go in horizontal to the main wedge and soaked again until the customer picked it up , the wood would be nice and swollen and advise the customer to soak it in water once a month if possible.

@urielventris4917 3 ай бұрын

Thanks brother! You answered about 4 questions I needed to resolve before starting my own axe (actually a splitting maul) recovery/restoration.

@andrzejporeda7281 3 ай бұрын

Super jest te siekiera stara zabytkowa odrestaurowana pozdrawiam serdecznie i polecam ten kanał wszystkim. 👍👍👍👍👍

@carrestore 4 ай бұрын

good job

@user-dy2xu7vj5g 4 ай бұрын

Чудова праця з металом !!! Лайкос .Нарешті сокира. Штамп якого виробника?

@jailsondasilva223 4 ай бұрын

Restaurado machado 🪓😉

@vasiliynovikov4926 3 ай бұрын

Работа конечно не плохая. Для очень начинающего чнловека. Но рукоять с дырами от термитов и клин из очень тонкого дерева это ОЧЕНЬ плохо.и срезание режущей кромки тоже плохо

@MOHAMADFETHANI5171. 4 ай бұрын

👍👍👍👍👍👍👍🇲🇦

@raihanfarrelofficial 4 ай бұрын

One handed

@globa-73globenko18 4 ай бұрын

"Молодец"... Срезал почти всю режущую часть с углеродкой. Можно было просто подточить кромку.😢

@ajizselam9116 3 ай бұрын

Fake

@user-og4qt1ms4t 15 күн бұрын

Так работа вполне годная, но не понял, зачем так сильно было срезать режущую кромку топора? Там трещины были или иные косяки? и второе, насколько будет держаться такой топор на одном вертикальном клине. По мне так нужен не только вертикальный. А так красиво канеш!