No video
Review and Running a Wilesco D-18 mini Steam Engine power plant on Live Steam
Рет қаралды 6,530
Күн бұрынUn boxing and Review a Wilesco D-18 mini Steam Engine on Live Steam. Using sterno for fuel the Wilesco boiler is fired up and the engine revved up to power a miniature generator and light the lamp.
Here is a link to buy the same engine in this video - amzn.to/3lmCyvq
This is a link to my video on the Wobbler oscillating steam engine - • Tear down homemade Osc...
Shop around for the engine you like. There are less expensive ones on the market.
Here is a video about the USA made Jensen steam engine - • Steam Up! How to run...
DISCLAIMER:
This video is intended solely for entertainment purposes. Any replication of experiments, projects, and creations, or anything similar, is the exclusive legal responsibility of the individuals replicating them. gwheyduke cannot be held liable for any information or misinformation, improper use, damage to personal property, death, or any other consequences that may arise from replicating any content viewed.
@lupo631 Жыл бұрын
Nice one. I got the same model three days ago, second hand. Some hints: Use preheated water that saves you fuel. The piston rod is mounted incorrectly. There must also be an opening for oiling. You can also see it from the fact that there is no opening for oiling on the screwed joint between the piston rod and piston. Both openings seem to be at the bottom due to the incorrect assembly, but they should be at the top. Just unscrew and turn. When oiling, the steam valve must be closed so that no oil can be pressed into the steam boiler. That can be dangerous. When oiling, unscrew the oiler screw, pour in oil and then turn the flywheel a few times with the oiler open so that the oil is sucked into the cylinder.
@gwheyduke Жыл бұрын
Thanks for the information. Great tip. Good luck with your engine.
@Tag-Traeumer 10 ай бұрын
I also wanted to write that the connecting rod sits upside down on the crankshaft. 👍 But why should it be dangerous if oil gets into the steam boiler? Of course, you should always close the valve when you open the lid of the oiler so that no steam escapes and the oil flows into the cylinder. To avoid corrosion I intentionally put some oil in my steam boiler, this protects the brass from possible dezincification, I think, in any case the oil doesn't bother. I also use the condensed water several times that I obtain in a homemade condenser, and this water contains some oil, which does not cause any difficulties.
@lupo631 10 ай бұрын
_"According to the regulations, oil should not be brought into the steam boilers because it easily causes seizures in the boiler, forms solid oil crusts, severely hinders the passage of heat etc., and should therefore be kept away from the condensates for feeding into the boilers"_ Source: Handbook of combustion technology and steam boiler operation. Author: Georg Herberg @@Tag-Traeumer
@lupo631 10 ай бұрын
_"To avoid corrosion, I intentionally put some oil in my steam boiler. This protects the brass from possible dezincification. I think the oil won’t bother me in any case.”_ In addition, everything is galvanized, so dezincification cannot take place at all. @@Tag-Traeumer
@lupo631 10 ай бұрын
find a nice video clip here on youtube how the Wilesco Steam Engines are made: kzfaq.info/get/bejne/h8ljmMaFqJ3FiKc.htmlsi=qOLq7dOlQc4hOd5N @@Tag-Traeumer
@gwheyduke 3 жыл бұрын
A very well built and good running model steam engine from Germany. it has lots of features like the pressure gage and blow down valve used in the full sized live steam engines.
@eliotreader8220 10 сағат бұрын
beautiful video of your steam engine. I have got a D18 that I display at model shows in France.
@gwheyduke 9 сағат бұрын
@@eliotreader8220 Thanks for the kind comments. Best of luck with your engines.
@EA-58 3 жыл бұрын
Great engine.
@gwheyduke 3 жыл бұрын
Thanks!
@eliotreader8220 9 сағат бұрын
way is the water lever so low in the boiler? you have to make sure there's enough water in it other wise if the boiler runs dry the heat will damage it
@gwheyduke 9 сағат бұрын
You have a very good observation! Good point.
@gyroplanefdk 3 жыл бұрын
Fairly sure the bulb in a LED soldered in, not screwed in. Yes use the larger pulley. Don't let the water level down below 1/4 -1/3 of glass, you could start compromising solder joints
@gwheyduke 3 жыл бұрын
Thanks for the good info
@tazzman2869 Жыл бұрын
The oil on the pulley of the dynamo could be causing the spring to slip and not grab like it should thus causing the pulley not to spin as fast as it should. The old style ones used a incandescent bulb but the newer ones from 2005 maybe a bit later or so used LED bulb. you can use a ohm meter to check the leads to the dynamo to the bulb. Take the leads off and check and if there is an issue youll need to disassemble the light post or try to screw the older style bulb in.
@lupo631 Жыл бұрын
@Tazz Man286 No, as I know, like my D18 model too, it has a pulley with notches on both the fly wheel pulley and the pulley of the generator, so the spring belt can't slip.
@gwheyduke 9 сағат бұрын
@@tazzman2869 Thanks for the information👍
@DavidDewis 3 жыл бұрын
Im really perplexed by the way you pronouse dynamo. lol. But great video.
@gwheyduke 3 жыл бұрын
Thanks for the comment. Glad you enjoyed.
Marty's Matchbox Makeovers
Рет қаралды 41 М.