Revival of a $1000 KX250 from Start to Finish

Рет қаралды 311,471

11 ай бұрын

I partnered with DupliColor for this project! Check out DupliColor products here: www.duplicolor.com/
Here are the specific DupliColor products I used for this project:
Prep Spray: qr.page/g/LFzwoxzHWv
Self-Etching Primer: qr.page/g/2ey4S9qmFDs
High-Performance Wheel Coating and Matte Clear Coat: qr.page/g/4vFVtjh9tMp
Acrylic Enamel and ClearCoat: qr.page/g/38edI4LQZsq
#ad #sponsored #duplicolorpartner
I bought a KX250 for $1000 a few months ago. This is the complete process I went through to bring it back to life from start to finish!
Instagram: / kincadepavich
TikTok: / kincadepavich
Support the channel by bookmarking this affiliate link to make your purchases on Rocky Mountain: www.rockymountainatvmc.com/?r...
This bike is kitted with brand new plastics from MX Plastics. Use the code “MXP10” for 10% off your next order: www.decalmx.com/productListin...
Along with custom graphics and a custom seat cover from DeCal Works: decalworks.com
Pryme MX products are essential for any bike build. I earn a small commission when you purchase Pryme products through this link: prymemx.com/?ref=kincade
This bike shines thanks to new hardware from Fast Metric: fastmetricfasteners.com
This bike is kitted with Pro X parts throughout: www.pro-x.com/
This bike is sure to grip thanks to some brand new tires from Shinko: shinkotireusa.com
Stuck Nutz is a new thread locker company dedicated to keeping trails and riding areas accessible. I support what they stand for and you should too! Save 10% on your order using the code "KP10": stuck-nutz.com/
First beat is "Daydream" by Chandler Bouldin
The remainder of the music is from Epidemic Sound:
Going for the Best by Daniel Fridell
So Long Comet by Coma Svensson
The Last Kiss by Ritchie Everett
Emily by Ritchie Everett
Just a Little Bit by Chris Shards
Summer Flirt by Autohacker
Starfields by Hallman
The Morgue by Cushy

Пікірлер: 296

@grantduininck6238 11 ай бұрын

6% + 1 individual enjoyed that shot. Commenting on Jani's behalf

@lassekirketerp2837 4 ай бұрын

@nicholasdamico8009 2 ай бұрын

@Mike_B_724 11 ай бұрын

All my fears about buying a used bike, all rolled into one video 😄 Great job on the rebuild.

@KincadePavich 11 ай бұрын

Hahah thank you!

@holymacarenafin2319 4 ай бұрын

Haha i buy used bikes with intention to open then up straight away. While checking If it run good but mostly i check shocks and lingages. Those are good i take it. Never trusting someones hours on piston storys.

@bve7397 9 ай бұрын

He has the garage, the body and the brains! Love you dude, hoping to be doing projects as such on my own someday, sadly deals arent as good around here.

@SkillCollectors 11 ай бұрын

Man that glass/sandpaper re-surfacing trick is money.

@dylansmith6364 3 ай бұрын

Smooth counter tops work good too!

@sombatone 10 ай бұрын

This was absolutely awesome and best work done... the bike looks so amazing

@corbinolsen12 11 ай бұрын

Watched each individual video on this build and gotta say the full build video was just as awesome. Liked the commentary through out on this one. Looking forward to the next project! Honda 😮

@KincadePavich 11 ай бұрын

Thanks so much for following along!

@dethamselv5482 11 ай бұрын

Great to see some ones project is going nicely along. My fram and engine just fell down after i painted so i’ll be starting alllll over again

@codycegla6065 11 ай бұрын

I'm auto tech and I appreciate the great workmanship that you do and the videos that you put out. Have ever thought doing what to look for video when buying a used bike?

@KincadePavich 11 ай бұрын

Thanks a lot! Truthfully I haven't really, I feel like there's good content available for that, but I may take it into consideration!

@Cartduckmann 11 ай бұрын

You should! It’s great to hear different opinions!

@MultiDragola 7 ай бұрын

@@KincadePavichyeah I'd rather you focus more on in depth rebuild stuff like transmission/engine work along with electrical.

@notthat1130 4 ай бұрын

@@KincadePavich I highly request this video, im currently looking for a trail bike and a project bike . I’ve been watching your videos along with some others, trying to educate myself on how to work on bikes. Myself and Im sure many more would highly appreciate a video talking about what to look for when shopping for used bikes . I’ve seemed to find a lot for a good price that say they run good but how do I know I’m not gonna run into issues like these such as previous mechanics making non beneficial add ons/repairs. Great videos keep it up!!

@matthewmansfield2384 10 ай бұрын

We've had a few '02 KX's. That year is really the best of all from '97-'06 - best motor character for sure. A "must do" however, is to put '03 triple clamps on it. Makes it a whole new bike that can actually turn with the front. A friend who was a race mechanic gave us all the goods on making KX's haul, so we implemented a few of his suggestions with great results...

@shannonjurgens3667 9 ай бұрын

Yup! The project that is too big to fail! You did the right thing. You upped the resale value.

@user-ke3ud2ew1h 11 ай бұрын

Rad!!! Happy to see you use the old style plastics for this kx. I would definitely race this bike!!

@motomatt3763 11 ай бұрын

That CR is definitely an old crusty deamon of the dirt.... Looking forward to what you make out of it. KX is dope!

@KincadePavich 11 ай бұрын

Thank you!

@jacap1sr 3 ай бұрын

Let's just replace everything while we're at it. I applaud you.

@batonchik25 7 ай бұрын

Such a great pleasure watching your videos! you've made an Awesome Job man

@damxn7345 11 ай бұрын

21:26 some people may not agree with me on this but when im working with stuck hardware on the vice i smack the vice handle with the mallet or sledge gets those seized bolts every time

@PsGamer-fz8uw 8 ай бұрын

Absolutely stunning

@tristanc150 11 ай бұрын

I love your restoring videos!

@KincadePavich 11 ай бұрын

Thank you!

@tomatoknuckles 11 ай бұрын

Even tho I watched every episode, i enjoyed watching this again. You're a good dude and you have a great eye for making bikes look great. God help you with that CR tho that's proper roached, haha. Look forward to the build.

@KincadePavich 11 ай бұрын

Thanks so much I appreciate your support and comments!

@Newmanrides 29 күн бұрын

Love this build ❤

@jz64 Ай бұрын

Great job the bike looks beautiful

@07murdoc28 11 ай бұрын

That is one 10/10 bike for sure!

@KingFriday274 7 ай бұрын

Wow. Inspired to go wrench now. Great work

@Sissypool 9 ай бұрын

I'm a 4-stroke guy (mainly because of the sound and power) but, I love Dirtbikes, none the less. I loved this video. It's a skill I wish I could do and love watching any who does.

@kenweis7913 10 ай бұрын

That takes serious commitment

@Alfoy57 4 ай бұрын

I really enjoy watching your videos.

@graememilne4202 11 ай бұрын

That kx looks like a new bike,well done on that job. Cant wait to see the CR gettin done,looks like a lot of work needed there but your the man.

@KincadePavich 11 ай бұрын

Thanks a ton! Stoked to tackle the CR!

@graememilne4202 11 ай бұрын

@@KincadePavich Cool,got 1987 CR250 im just about to get stuck into as well. You got a good thing going on here,please keep it up,you only have to read a few comments to see how much folks are enjoying them. :)

@Grunzaa 9 ай бұрын

Love the bench grinder on the outdoor glass table 🤣🤣

@jacobEstammel 27 күн бұрын

finally !!!!!!!!!!!!!! a sand blaster

@martyross1573 11 ай бұрын

Can't wait for the CR. The black looks mean :)

@DirectoutdoorsTV 7 ай бұрын

Buddys jacked

@brettlaage9687 11 ай бұрын

Man that thing looks amazing! I can’t wait for the CR. I’m building a 2002 CR125 right now.

@KincadePavich 11 ай бұрын

Awesome, and thank you!!

@ChadJorgenson 6 ай бұрын

Some nice tips and tricks I'm going to use on my '00 KX250 ... though I actually love the raw aluminum color of the wheels, I hate the black on my new bike. 😀Love that case sticker, I'll be grabbing one of those for sure.

@Dirt_Breaker 4 ай бұрын

Pro tip, when resurfacing a cylinder try to go in an infinity symbol type pattern to avoid shaving too much off from one side, as you’ll find your fingers might weigh down one side more than the other. Also, make sure to regularly clean your sand paper, the shavings can build up and glaze the surface, reducing the bite on the gasket. Love the rebuild, not to much or to little!

@rossilake218 7 ай бұрын

Hi, Use 1/4" to 3/8" green tempered shelf glass. Make sure is is on a perfectly flat surface. I use an old counter top. You need copper jaws on your vice. I'll make a pair for you. I have that (20) vice/s..Great job on the rebuilds. I'm 62, Hobby machinist. I'm looking for a Cr250r late model. I had 3 and sold all of them, back in the day. Urrgh! Serb or croat? Redbud is our track.

@user-rw1cg8yi7l 11 ай бұрын

I love your restoration bike😊

@KadeTurner 11 ай бұрын

Really good video mate, lot of work gone into it. Makes me miss my 250. Wish I never sold it.

@alessandro519 11 ай бұрын

Awesome job!

@whatisaray 11 ай бұрын

Best part of the video is removing the kickstart lever 😂 good work I wish I would have documented my build like this.

@KincadePavich 11 ай бұрын

Took so long hahaha! Thank you!

@spiritofogun5583 10 ай бұрын

Excellent work bro

@ryanharriss7950 7 ай бұрын

That tyre remover is pretty good.

@sakisSAVAGER 11 ай бұрын

I love your work brother!!! Keep it up

@KincadePavich 11 ай бұрын

Thank you!

@richardstewart5095 9 ай бұрын

Awesome stuff!

@memorris2 10 ай бұрын

Bro, i had a 96 xr600r that was street legal when i bought it in 2015, and 90% of the spokes wouldnt tighten or loosen. I was broke at the time so i just rode it anyway. The rear wheel ended up exploding, cracking the wheel and luckily i was only going about 10mph in a turn. Lowsided and even with jeans on my entire shin was skinless! Always check old wheels and spokes!!!!

@memorris2 10 ай бұрын

It actually might have been a 93 xr600r now that im thinking about it haha

@sexatica 10 ай бұрын

great music in the video. Very satisfying

@KincadePavich 10 ай бұрын

Glad you liked it!

@martyross1573 11 ай бұрын

Good videos. Keep them coming

@ODRoach 11 ай бұрын

always RAD my dude! Keep it up

@KincadePavich 11 ай бұрын

Appreciate it!

@WOLFEY0812 11 ай бұрын

Great job bro 👍

@joelboutier1736 5 ай бұрын

beautiful bike. sometimes the cheapest bikes are the most expensive

@brianhuman2218 11 ай бұрын

Loved this series man! 🔥

@KincadePavich 11 ай бұрын

Thanks for following along!

@brianhuman2218 11 ай бұрын

@@KincadePavich can't wait for the next one

@CNNECTCTRAL81 9 ай бұрын

My dad owned the same KX when I was a little kid, you got me inspired to something similiar :D

@tomrotella6273 11 ай бұрын

Really enjoy watching your videos. Great insight for when I finally get a bike lol 😂.

@KincadePavich 11 ай бұрын

Thanks a ton!

@tunahtuckkingrichard8052 10 ай бұрын

Great job.

@SimonQuennevilleSim 10 ай бұрын

killed it

@Adjust-Fire-jy3dy 3 ай бұрын

I have to say this is about what to expect every time you buy a used 2 stroke. I have done it many times. The fact that I love doing it doesn't justify it in my wife's eyes though. Lol.

@Menniti_129 11 ай бұрын

im excited for the honda i know your gonna build a sweet bike!

@KincadePavich 11 ай бұрын

Thank you!

@Rhutt258 10 ай бұрын

Insane

@vincentwobb9919 5 ай бұрын

If you ever have to cut a sleeve or even a bearing off, cut it with a die grinder but don’t go all the way through, then take a cold chisel to your cut and it’ll usually split along that cut and won’t damage the shaft, I use this all the time at work.

@jimmyjohnson2827 10 ай бұрын

That music on the engine teardown lol

@shaqfryz6481 11 ай бұрын

Gotta see this thing rip buddy !

@KincadePavich 11 ай бұрын

Vid just went live!

@UTP_ENT 9 күн бұрын

What’s your fitness routine ? “Disassembling old dirt bikes”

@nuthintoprove 10 ай бұрын

Every time I buy a used bike I plan on at least what you did? Nothing here surprised me!

@upsideways 6 ай бұрын

New subscriber here. Loved this clean-up. Looks amazing

@Hahzi 5 ай бұрын

As a female, I appreciated it

@joshellis6801 11 ай бұрын

Your videos are so good

@KincadePavich 11 ай бұрын

Thank you!

@Tmoney423 11 ай бұрын

Sick!🤘

@chasebenzing7824 11 ай бұрын

Man, love the bike, just rebuilt my ktm250, nice job!!

@KincadePavich 11 ай бұрын

Awesome! And thank you!

@XxGhostR3c0nsxX 11 ай бұрын

That Baby is Sweet!!!

@MegaQLDER 7 ай бұрын

U had me at kx 2 stroke. But the shot of the rig?, haha😂

@sickunit2096 2 ай бұрын

Ive used that very same shop vac extension to drive MTB fork bearing races 😂

@marafade13 5 ай бұрын

Music choice for the assembly ❤

@Ridefastorgetpassed 6 ай бұрын

Next time prepack those stem bearings with a bearing packer then tap em on. I also wipe a little grease in the cup/race.

@josephsworld1886 9 ай бұрын

Love the number you chose. (406) That’s my race number. 😂😂

@friguy4444 7 ай бұрын

Wow dude!! You've got a Hockey net??!! MAN!!

@KincadePavich 7 ай бұрын

I play adult league hockey here!

@tebow3068 8 ай бұрын

I just bought a 94' kx250, i have a similar isuue with the top end because the walls have been worn down so ill have to get a whole new big bore kit otherwise it'll keep burning up my oil

@lorenzohuerta8701 11 ай бұрын

Man as someone who would literally kill to own a dirtbike i love watching ur restoration videos learning the ins and the outs of them one dayy ill be fixing up my own 🤞🏼

@lorenzohuerta8701 11 ай бұрын

@@Message-M6 wait is this real

@KincadePavich 11 ай бұрын

Thanks a ton, I believe you will! And I see you response - no, I will never notify anyone of a bike giveaway via KZfaq comments. You gotta be careful of scammers!

@lorenzohuerta8701 11 ай бұрын

@@KincadePavich yea i kinda figured got really excited but figured it was too good to be true 😂😔

@kenweis7913 10 ай бұрын

I love shinko tires for the price and performance

@jcrr1972 9 ай бұрын

I wish I have the time, tools and knowledge to this, great job!!!, wonder what the original owner is thinking now.

@2stroketyson79 10 ай бұрын

you can use a PVC pipe for the steering stem bearing too

@40mmmikemike 10 ай бұрын

Theres always some valuable information in these videos for people who like to work on things. I was thinking it might have been better finding a brand new coil instead of that old one for that price.

@Altie8 Ай бұрын

i learn s0 much

@Ernbern124 11 ай бұрын

damn next project is clapped out.... Please keep that shred decal or re do it. Looks badass.

@KincadePavich 11 ай бұрын

Hmmm... Will consider... :)

@lawrencefranck9417 11 ай бұрын

Try penetrating oil. Liquid wrench makes good stuff that will dissolve rust almost instantly. I use aerokroil if I can get it.

@Big__Ry 7 ай бұрын

Great video 😂😂

@IAmPiernik Ай бұрын

Girls, 7:20 You're welcome! Love it 😂😂🥵

@gtgodbear6320 3 ай бұрын

I've been hoping I could find a cheap 85cc to restore. Honda, Yamaha or Kawasaki. They have always been my favorite size.

@jameschapa5111 3 ай бұрын

nice work However noticed when you put grease on stem bearings You should watch a video on packing hub type bearings You will be surprised on how much grease they use.

@nathancorlett9895 9 ай бұрын

Great vid m8 what was the total money spent on bike thanks

@microsoftteams2663 6 ай бұрын

I have NEVER seen rusty bearings like that>>>>>>>>>>>>> Whhhoooooo!

@tmk5522 6 ай бұрын

That bike was completely clapped out

@ginos5081 5 ай бұрын

how did you biy the piston without knowing the cylinder diameter? simply took the same size as the one that the bike came with?

@fatbongripz4207 9 ай бұрын

looks like that axle nut hasn't been greased in a very long time. i do it every time i change the tire, i thought that was common knowledge. i have the 4 stroke version ('05 250f) i abused it heavily when i was a teenager. would love to buy new parts for it but parts are getting hard to find

@Niobium23 10 ай бұрын

Awesome! Hahahaha, spoke removal is sexy, I’ve always said that.

@no-namecrown5510 10 ай бұрын

I have a 96 KX 250 and I'm looking to replace the OEM triple clamps with aftermarket billet. I'm in Australia and can't find a supplier. Any USA suggestions? You guy's have the best products.

@michaeltyris3249 3 ай бұрын

I think you need to invest in an ultrasonic cleaner for your carbon stuff or anything else engine wise tbh, easy and gets into every single nook and granny!

@grudzien9784 9 ай бұрын

I don’t know about you, but the clips I think are the hardest to install lol. The 65 sx I did it took me forever to get the in correctly. Not to mention I lost those little clips at least 10 times and had to look for em. So frustrating