In this video, 180 degree coupler is designed and simulated to find out its S-parameters. The even-odd mode analysis video is available here • Even-odd mode analysis...
Пікірлер: 31
@user-bd4jz7ll6jАй бұрын
Thank you sir for this amazing tutorial 🙏 You are truly a life savior
@Lukky070919983 жыл бұрын
Thanks sir for the video. It helped me with my project as well. :)
@saikikusuo73614 жыл бұрын
Thanks a lot Sir.
@reshmap58214 жыл бұрын
Thank you sir
@taher98544 жыл бұрын
Thanks alot sir this helped me so much in my project
@RFDesignbasics4 жыл бұрын
Welcome
@mohamedassaghir17514 жыл бұрын
منور علوص ههههههههه حتي اني خاش بندير منه البروجكت
@taher98544 жыл бұрын
@@mohamedassaghir1751 هههههه تعالي خاص ع الماسنجر ياصغير كملته واتي المشروع باش نبعتهولك
@siddharthmohanty71064 жыл бұрын
Thank you Sir! Very informative video
@KGunjanYadav4 жыл бұрын
Well explained 👍
@RFDesignbasics4 жыл бұрын
Thanks a lot. 🙂
@shambamitra65973 жыл бұрын
can you please help in designing a wilkinson power divider?
@RFDesignbasics3 жыл бұрын
Will do it soon.
@shambamitra65973 жыл бұрын
@@RFDesignbasics thank you very much..I am in dire need of that..:)
@RFDesignbasics3 жыл бұрын
But that is only possible with circuit schematic of the HFSS 16 onwards
@shambamitra65973 жыл бұрын
@@RFDesignbasics I use hfss19. But I am not able to design it. there is a use of resister also I don't know how to incorporate it.
@RFDesignbasics3 жыл бұрын
Ok. Will do it soon
@mohammadhafiez74474 ай бұрын
can you provide training on hfss design
@RFDesignbasics4 ай бұрын
Recently we did workshop on HFSS.
@DevendraSingh-jm2ys3 жыл бұрын
Sir how can i design UWB power divider in hfss please tell me sir If possible please make an video on power divider
@phuonghieu84513 жыл бұрын
how can i draw half a circle? can you teach me?
@RFDesignbasics3 жыл бұрын
Draw a full circle and draw a rectangle on half side. Cut the rectangle from circle.
@phuonghieu84513 жыл бұрын
@@RFDesignbasics how can i draw the circuit crve? can you teach me?
@jeiac93 жыл бұрын
Excuse me, how could I have the exact value of the radius?
@RFDesignbasics3 жыл бұрын
You can calculate using the circumference of the coupler which is 1.5 times lambda.
@jeiac93 жыл бұрын
@@RFDesignbasics some document in which there is an example perhaps?
@RFDesignbasics3 жыл бұрын
You may refer 'Microwave Engineering' by DM Pozar
@jeiac93 жыл бұрын
r = 360 degrees * L / 2Pi (90 degrees) Can this formula be applied? 
@RFDesignbasics3 жыл бұрын
If you know length L i.e. circumference then just divide by 2pi to get r.