Cheers dude , just saved me 100's of euro, I had checked every thing fuses , wiring, hand controls just spent 2 hours trying to find problem, came back in , found your vid and there it was the seat belt , thanks man

You just saved me big dawg. Thanks 💯💯💯

Your Slappin some coughnut!!! Sickkkk

Helpful video bro and he slapping that "cougnut" wild west yeeeeeee 💯

Thank you for making this video

In the last part of your video you cut a wire to the solenoid. Which wire did you cut?

I had some friends set one up in my 73 Ford Econoline, I wired it up, been using it for years, had to repair the socket for the remote, added ubolts to secure it, kept pulling lose, refusing to work, I have no safety switches, just that stupid seat belt, gonna cross that out soon so I don't have it on the arm. These lifts are fantastic, durable, so long as there is minimal electronics on it for long term trouble free use. Mine was made in 1995, it needs the springs replaced, I have to pull it out, but I can't replace them myself, nor can I afford to get them replaced at a shop. I put the circuit breaker in the floor by my lift, there is a blade fuse or two under the plastic cover over the motor housing, only thing to interrupt operation for me was the breaker tripped.

Hello would you be able to help me out when i put the ramp into stowing position it does not go all the way up it just stops and hangs at a level you can hear the motor going but the ramp does not move

Where do you get the tools to work on that lift?

Thanks for this video, really helpful. Wonder if you can help? The yellow tail flap doesn't always deploy properly and when the lift is at ground level the flap is sticking up, too much for my wheelchair to go over! If I've got help, they can stand on it, it'll go flat then, but on my own, I'm stuck. Do you know of a way of adjusting that? Kind Regards and greetings from North Wales UK

These Ricon lifts are the best. I prefer them over the Braun millenium any day. The ricons are so much quieter than the brauns. Does the ricon use hydrolics to bring the platform down to the ground? Reason i ask is because i dont hear the motor running while traveling down, but i do hear it while traveling up. The braun lifts you can hear the motor bring it down as well as up. If the ricons use hydrolics to bring platform down, then thats a great advantage as you are not waisting your vans battery as much. I know hydrolic elevators work same way. You have a loud ride going up as its using the motor to push tbe cylinder up to push elevator up shaft, but going down, the ride is so quiet. You can barely hear the air being exhausted from the cylinder. So no motor operation going down, but motor operation going up.

I hàve a k series that will not deploy from stowed position. Where should I start looking can I jumper the pendant button

My 1997 Rikon will come down to the load position from while inside but it wont lower to tne ground! unless i turn the float to open a bit. It will lift and stow, just not lower to the ground. any ideas? no action at the remote switch.

Hey my friend. That bridgeplate sensor, how do you adjust it?

Alejandro, I have a question for you. I have tried my best to locate this info before asking online. I have the Service Manual for my 2010 S Series Public Use Lift. I have not been able to locate wiring diagrams or other related info concerning the Ford fitted interface system or the lock out systems. Some of the lock out systems will be deleted. This bus will be used for an exterior cleaning business and the lift for pressure washers and other related equipment. Many thanks for your video and info! Darryl

help. my lift will not deploy with control it only clicks. however i can deploy it manually and i can go up and stow with control

Sometimes my lift doors will open like normal but the lift won't deploy. I hear no clicking sound either sometimes. Which solenoid do you think it could be, The one closest to the passenger seat on the floor or the solenoid (the silver one) on the lift's post?

Dope, my pressure switch it triggering, guess I adjust the ramp cables. Thanks~! 10 haters... lol why?

Hey bro... Could you help me diagnose my ricon lift?

My lift has no power lights don't work. where is the fuse?

My mother has an S2003 lift that will rise, but will not tip from horizontal to vertical once it is level with the platform. It will work with manual pumping. Is it the switch? Or electrical connection? In a small town and trying to determine if we can fix it ourselves.

Can the pressure switch be adjusted?