rim cylinder switch on a Von Duprin Alarmed exit device with stripped mounting holes

No video

rim cylinder switch on a Von Duprin Alarmed exit device with stripped mounting holes

Рет қаралды 10,850

SE Lock and Key

Күн бұрын

It ended up being a bit more work

Пікірлер: 52

@RaulRodriguez-fj4mo Жыл бұрын

Great job Jason a typical day for a locksmith with some jobs some day easy some day pain in the ass YOU SHOW IT AS IT IS

@lynh8378 2 жыл бұрын

Lol. I always had a roll of duck tape as I usually didn't have help ....

@swgeorgia 5 жыл бұрын

welding magnets make a great third arm for holding panic bars up while inserting screws. Also insert the rim cylinder into a thin wall pvc pipe the appropriate length cut a slot the length of the pipe so you can insert it into the door through the cylinder hole. Then you can tighten the rim cylinder screws without distorting the door.

@rabbit_abel 3 жыл бұрын

yeah what he said

@petewoodfine2100 5 жыл бұрын

Hi Jason. Wow. That was a fun job. I bet. Just proves you have to be prepared for things not to go as planned. Thanks for taking the time to do this video. It just shows that you can't buy experience. I bet a newbie would have been stumped and not known what was going wrong.

@DD-su5so 5 жыл бұрын

Nice video. Teck tip...i use Horible Freight (US)Pricess auto (Canada)big welding magnets and a piece of 3"wide..mild steel flat bar to create a shelf to support the panic bar while I mess around with the install...

@JeffreyRosenthal1 5 жыл бұрын

I like that idea

@Mirauge 4 жыл бұрын

So someone actually did it. I remembered the influx of reality tv shows that went into exterminators and all kinds of stuff. And as I locksmith I wondered what if I took a camera along. But I knew it couldn't do very well. As i expected though. Its interesting to watch back. Thanks for sharing your experiences. You remind me a lot of myself.

@kevinkoepke8311 5 жыл бұрын

Great lesson. You need one of those two handled rivnut squeezers.

@selock 5 жыл бұрын

Kevin Koepke yep 😂

@tuba7084 5 жыл бұрын

I’ve got one. Just don’t over do it on the nutsert. Or you will be drilling the darn thing out! I happen to know from personal experience with those darn things!

@7guitarlady 3 жыл бұрын

So what about the inside cylinder? I'm getting ready to do this today, but I didn't see where you replaced the inside cylinder?

@selock 3 жыл бұрын

Once you pull the main cap you will see (as I recall) two or three screws holding the bracket mechanism for the lock. There is also a long round cam cylinder that the tailpiece engages with. I didn't have to pull the inside cylinder on this one cause it wasn't loose :) Its not hard to figure out though once you get the cap off

@primelocksmith8876 5 ай бұрын

switched out core, how would you go about if customer asked for same operating key ?

@dennischausse3075 3 жыл бұрын

Jason I am lost what did you put in the striped holes ???

@selock 3 жыл бұрын

Time stamp?

@jimjones1678 5 жыл бұрын

Thanks for the videos. I love watching. Great job on that door. Definitely a pain the rear.

@waynegrant1712 5 жыл бұрын

This job required talent and tenacity, nerve and verve, and only one person has these noble attributes in the land of Jackson, Mississippi, and that is the prince of Fondren. Also known as locksmith extraordinaire, creator and director of cinematography for SE Lock and Key. Job well done, bro!

@billinphoenix255 5 жыл бұрын

I have a nutsert tool but I can't get my hand around it to pull it tight so I just use a small bolt tool and wrench. Some days you just have to go the extra mile (or half hour), good job Jason.

@swgeorgia 5 жыл бұрын

Replace stripped out screw holes in metal doors with pop rivet threaded inserts.

@DD-su5so 5 жыл бұрын

Yep the easy way.

@bradw0535 5 жыл бұрын

Nice work Jason! Thoroughly enjoyed the info, tips, along with the entertaining side notes :-)

@rodsphotography1 4 жыл бұрын

I feel for you Jason. It’s like every job I go to Nice work Jason

@RICKRAZO 4 жыл бұрын

Great job and thanks for the video I’m learning lots

@pjdambra 5 жыл бұрын

One of those jobs Jason. If it ain’t one thing it’s another. It came out great. Chuck that one up for experience. Sounded like an insane asylum to work in.

@rabbit_abel 3 жыл бұрын

love you bro you got it done all that matters

@GottSegneDich 5 жыл бұрын

They seriously overpaid for a Von Duprin when a Detex is easier to service and is cheaper with R&R.

@selock 5 жыл бұрын

Diener Christi that they did!

@ryanbradley4718 5 жыл бұрын

I think the von duprin is more secure. I recently replaced a detex unit on a best buy receiving door because someone pried the full length security astragal away then pried the door open breaking the latch on the panic device (the door held up well). That same week I visited a restaurant back door with a von duprin unit to quote a new door and frame due to the damage but the attempted intruder didn't gain access and the von duprin unit is reuseable. Of course, the best buy intruder may have had a longer pry bar.

@moishemgrinberg 5 жыл бұрын

I think you did a great job the only thing I would add would be an impact wrench instead of the ratchet but you still deserve kudos for perseviring.

@rayhorner2965 4 жыл бұрын

Umm!

@KingStreetRob 5 жыл бұрын

Lot's of fun. At least for us watching. Not so much for the poor guy at the end of the tools. Nice work Jason.

@ImGumbyDangit 3 жыл бұрын

Can believe I missed this video before. I think I'll go back to the Fire Department door and add the rivets. (And looks like one heavy ass exit device)

@selock 3 жыл бұрын

its just ginarmous but not really that heavy, mostly aluminum

@peterzenner2020 3 жыл бұрын

How did people fix stripped holes in metal prior to "Nutsert"? Just drill and tap for bigger screws?

@hkssystemslocksafe2486 3 жыл бұрын

GKL actually makes a slight oversized set of screws for metal and wood use. Comes in handy!!!

@killer2600 7 ай бұрын

Weld the hole and redrill

@bird718 5 жыл бұрын

thats a lot of work

@jdub5107 4 жыл бұрын

Why did the alarm go off every now and then? Nice vid.

@dsloop3907 5 жыл бұрын

That door looks battered on the upper part of the face. Why Never let the tip touch? Quickserts are a pita. What was in that place worth stealing? Pro Tip- Put a shop towel or glove between your hand and the allen wrench when you are putting extreme torque on it like that. They can BREAK and the edge will cut like a razor, making much blood and pain. I know this first hand. Try your Dewalt impact driver on the Quickserts in a piece of scrap. FO REAL

@selock 5 жыл бұрын

D Sloop that’s why I stopped torquing I had horrible visions of it snapping and shooting through my hand

@selock 5 жыл бұрын

Never let tip touch will be covered in our coming soon extraordinary loctite video!

@jeffmoss26 5 жыл бұрын

more power!

@miccowolf4601 5 жыл бұрын

This locks are the best lock you can buy easy rekey best value for your money

@ken_9359 5 жыл бұрын

Another great video by Meeks Production company.

@mikekozera5308 5 жыл бұрын

What tool did you use to cut that tailpiece? I usually have to grab a dremel with a cut off wheel and a pair of needle nose pliers when there are no pre-cut sections on the tailpiece.

@selock 5 жыл бұрын

Mike Kozera $10 mini bolt cutter tool from Home Depot

@rayhorner2965 4 жыл бұрын

Too long is better than too short. If wrong, it had to replace the tailpiece. It means more work.

@willie_mccoy 3 жыл бұрын

A bit quicker way to install those rivet nuts: kzfaq.info/get/bejne/mcucaqmd0c7ceoE.html

@DonzLockz 5 жыл бұрын

The seemingly simple jobs can take ages and visa versa. I wouldn't turn my back on that rowdy bunch though. Lol. 😉✌

@williammurrayphotography 5 жыл бұрын

Ha! I feel for you Jason. It’s like every job I go to...”just a simple rekey job, shouldn’t take that long” , as the wife is blowing up my phone. Great job.