Roban EC-135 superscale 800 from Karsten Illig - Scaleflying Scale-Helimeeting 2018

Рет қаралды 18,099

5 жыл бұрын

watch in Full HD 60p
Out of the Box with
Standard AW: Roban EC 135 Super Scale 800
Hacker A50-12L 450Kv
Jeti Master Mezon 115 Opto
TS 3x 1258TG
Heck 1283SG
BD 3X
Emcotec SPS
Jeti BEC 2D
2x6S 5000
Event: 1. Scaleflying Scale-Helimeeting 2018 (Lockhausen)
More RC Model Videos on my Channel and Playlists
Videos Pöting Turbinenmeeting
• 17. Pöting Turbinenmee...
Videos DMFV Scale Helimeeting
• 11. DMFV Heli Scalemee...
Videos EC-145 ADAC
• EC 145 ADAC
Videos Heidelberger Vatertagstreffen
• 21. Heidelberger Vater...
Intermodellbau Dortmund
• Intermodellbau Dortmun...
Rotor live
• Rotor Live 2018
like and subscribe
kzfaq.info...
@HeliChrissi

Пікірлер: 17

@JohnVHRC 4 ай бұрын

I need a scale heli real bad..

@pierreh9373 5 жыл бұрын

The tail travel on the helicopter is very light. Having a hard time setting my throttle curve due to this issue. I was attempting to fly at a flat throttle curve of 75%.l, but the torque from the main rotor was too much for the naza in Heading Hold and rate mode. Is it safe to attempt to fly with a 50/60 % throttle curve being that the tail seems to hold there. If not, can you share your pitch and throttle curves with me??

@P222RL 2 ай бұрын

I have around 6 flights of my ec130, seems the tail blades getting larger plays, I guess around 2-3 degree, causing it does not have enough force to turn the tail at hovering when wind is over 8 knots, do u find this issue ? I have to do left turn instead

@ChrissiRC 2 ай бұрын

In flight it is a known problem to fly into turns in one direction with the Fenestron. You then have to fly the curve with more roll. but during hovering, i havnt heard of this problem.

@dylanmorgan474 Жыл бұрын

I’m in the middle of this build right now. I’m having an issue with the tail Boom assembly. The manual does not line up with the parts I have. Could you send me some pictures of the tail boom servo and push rod set up? Also, can’t tell where to fasten the tail stabilizing arms at the fear box.

@ChrissiRC Жыл бұрын

Sorry, but I don’t have an EC135! I’m just the Filmer

@russellsvideos7260 2 жыл бұрын

Hi I am experience pilot just recently got the EC135T3 Setting it up with the spectrum FC6250HX FBL Setting it up on the workbench notice high RPMs the tail rotor does not work 50% throttle seems like the tail rotor is working now seems like the rotorhead speed is really low in order for this tail rotor to work no matter what you do higher RPMs it does not work is that correct please help. I guess I’ll let you know how that works out if you could tell me your set up that would be great. am I right about the lower RPMs for scale to work correctly you would think the higher RPMs the tail rotor would respond better

@ChrissiRC 2 жыл бұрын

Hi, the best thing to do is contact scaleflying.de, the german distributor of roban helis. the owner is also the pilot in this video. he can best help you i think. regards

@russellsvideos7260 2 жыл бұрын

@@ChrissiRC OK thanks for the quick reply I’m trying to get a hold of them I’ll let you know what the outcome is.

@P222RL 2 ай бұрын

I am using 50kg tail servo , it helps, yet it cannot cater when wind speed is over 10 knots , because the play of the tail pitch causing a very low output of tail wind even u push a full right of rudder