Robotic Welding Training - Performing A Dry Run

Рет қаралды 103,775

10 жыл бұрын

Пікірлер: 75

@Iambetterthanyouanduknowit 2 жыл бұрын

Man thank you for this video, I’m a millwright apprentice and the other millwright who works these robots is in school tmrw and it will be me in that area and this video is really gonna help me figure out what I’m doing, so thank you!!!

@twicked1 5 жыл бұрын

Top Notch Video ...make more please ;)

@salaudinkazi9517 2 жыл бұрын

Thanks man need more video

@golothrom3762 5 жыл бұрын

@Rahul The question you have is about the interpolation types. MoveP = Moves the robot position based on the points. MoveL = linear welding. (The robot welds line to line following the points.) MoveC = circular welding. (Using 3 points [start, amplitude, and end.] Makes a curved weld.) MoveLW = Linear weaving. (Using 1 start point 2 amplitude (weavep) points and 1 end point you can have a zigzag straight weld.) MoveCW = Circular Weaving. Same as above, just circular. @Thor That's cartesian mode for X,Y,Z you can also move the robot on many different ways including quantitative movement, tool, and even moving each joint of the robot on it's own. I would probably be careful doing any of that though as it could really mess things up if you have no idea what to do. Adjusting weld parameters is very simple, all you must do is go to the start of the weld and select the programming box and press enter. You should have a popup menu (if not locked out) and you can adjust your parameters there. Careful modifying parameters if you don't know what you're doing, that can result in a lot of bad welds, no welds, or burn through depending on your materials.

@souciabderrazek6741 5 жыл бұрын

Thank you can you give me the adjustment for the post to weld and the Tension, intensity and speed I appreciate that

@JuanMendoza-ne3om 6 жыл бұрын

Thanks just started working with this robot and my teacher has really bad English so hard to understand and your video is a lot clearer?

@pablocalvillo8921 10 ай бұрын

Yeah I’m dealing with the same person right now so frustrating and he legit told me he doesn’t want to train me due to job security. Thank god I found this video

@ionutm7438 6 жыл бұрын

the best of the world!

@pepl2018 Жыл бұрын

Great sir

@christianbernal2826 2 жыл бұрын

how did you do it can you share with me , thank you

@Sudhakar1997 5 жыл бұрын

Pls do another video about robot teaching

@Sudhakar1997 5 жыл бұрын

Sir please once again you tell that full detail about robotic welding kit and uses of full buttons please

@sylvestercalzone1003 5 жыл бұрын

Hey guys, I’m currently being taught how to use one these robots at my work. Where would you suggest I go to actually learn this stuff? Im a welder full time at my plant but I wanna get into robotics and cnc work. Where do I start?

@MikeD4 5 жыл бұрын

joe gomulka Miller has a school they can send you if they are interested in buying one

@tonybowers5476 5 жыл бұрын

i attended miller's 1 week training coarse in Chicago this past week. its complicated but I have a good idea now. I suggest you attend.

@swilliams9919 4 жыл бұрын

Tony Bowers I assume James Manning was your teacher? Carol Stream Illinois?

@completesolution6088 4 жыл бұрын

Dear sir you are doing great job, please help me for teaching and program of Panasonic robot

@joelcabrera489 2 жыл бұрын

The servor doesn’t turn on. What is the problem?

@edneiaaparecidafreitas1254 5 жыл бұрын

Tem como fazer um vídeo deste explicando em portugues por favor? Obligado

@danielamontoyavelasco657 5 жыл бұрын

Goodnight. Friend, I operate a powermig panasonic MT 1800 welding robot, it is to ask you how to make the robot work by welding several pieces at the same time without having to make them one by one, if not from the first one you can leave the others . Thank you... Greetings from Colombia

@s.p.technical3547 5 жыл бұрын

Also make all video in teach panel

@yogeshthakor6096 6 жыл бұрын

Very nice

@rbthakor.103 6 жыл бұрын

yogesh thakor ..Hi yogesh

@princekhan173 3 жыл бұрын

I'm a service engineer of Panasonic Robot in North India.

@williamhuang5329 Жыл бұрын

Hanzhen harmonic drive gear , strain wave reducer, robot joint , over 30 years experience

@sandhyredhat8193 7 жыл бұрын

Do you know how to set hot speed, i'm interesting to a make progam weld robot panasonic

@MikeD4 6 жыл бұрын

sandhy redhat no, I am not familiar with that

@84efuentes 5 жыл бұрын

Hi! Can you tell me how to activate the lpck when the table has been rotated, please?

@MikeD4 5 жыл бұрын

Ernesto Fuentes I am not sure what lpck is? If you mean the table lock, switch the left upper switch on the front to straight up and down. You can then rotate the table and get it locked back in place

@84efuentes 5 жыл бұрын

Do you mean TO SET THE MODE SWITCH TO AUTO MODE? WE TRIED THAT BUT HAD NO LUCK. sorry about the capita letters i kust notice. Lol

@dustintatum5057 Жыл бұрын

I would like to get in touch with you I just started my career doing what your doing and I’m struggling on programming touch points

@MikeD4 11 ай бұрын

It takes some practice at first to get the right angles and distance. Make sure you are trimming your wire stick out to the correct length before programming your moves.

@belalsenkata762 5 жыл бұрын

Make clamping decamping video

@jasuram4319 3 жыл бұрын

Sir master program me input kaise dalte h

@swilliams9919 4 жыл бұрын

Let me know when your ready to take your programming to the next level.

@jasuram4319 3 жыл бұрын

Sir please new program kaise banate

@podprogrampiotrq8058 5 жыл бұрын

Hello mate! Have you got some manuals for this pendant ? Thanks

@MikeD4 5 жыл бұрын

LowGraviTV I don’t have anything

@podprogrampiotrq8058 5 жыл бұрын

Ok Thank you

@swilliams9919 4 жыл бұрын

Michael David I can send you a zip file for the manual if you like.

@mustakshaikh6108 4 жыл бұрын

I have some PPT WHICH help you to make program and advanse command

@md.rafiqulislam5243 2 жыл бұрын

@@mustakshaikh6108 Can you help me out brother

@rahulrawat450 5 жыл бұрын

What is use of MOVER moveL or what difference each athore

@valiantthor3796 5 жыл бұрын

Go into teach mode and select f1 then robot icon at bottom left then you get options x, y, Z, theese are all different movements, I'm not an expert I'm still learning myself

@swilliams9919 4 жыл бұрын

MoveL is linear movements. These should be used during most weld positions and tight areas of air cuts. MoveP. Is point to point or otherwise known as joint movements. These should be used for quick air cuts. Not for weld points for they are less accurate than MoveL is. MoveC are circular points. These require a minimum of 3 points. MoveLW is linear weave. MoveCW is circular weaving. Weave P is an attribute for weaving.

@mortezaeshaghzadeh9241 4 жыл бұрын

Hi . How can I find this robot machine manuals because I'm trained right now and I want the guidance notes .please let me know. Thank you

@MikeD4 4 жыл бұрын

You would need to contact the manufacturer for those

@mortezaeshaghzadeh9241 4 жыл бұрын

@@MikeD4 I find the model number (YA-1TA )(G III controllers TAWERS)of the robot that I work with that. Actually now I need to contact with manufacturer but I don't know how can I send and email for requesting help. Can you tell me the manufacturer email address please?

@Sudhakar1997 5 жыл бұрын

Sir plz video make in how to programming and adjusting parameters

@tonybowers5476 5 жыл бұрын

you need to attend the 1 week training coarse at their Chicago facility. I was just there this past week and have a fairly good understanding now.

@lalittyagi5012 6 жыл бұрын

How to feed a new program in this robots specially when there is circular interpolation?please upload the video on this.and please suggest me how can i learn its concept.

@mdwadudrahman4118 3 жыл бұрын

I want to know easy system

@navneetsingh2124 4 жыл бұрын

Can you please tell me , how to teach movelw weaving weld??

@MikeD4 4 жыл бұрын

We have been busy this year and I have not created any new videos. I just got a 4'x10' robot welder from Miller that I hope to shoot some videos on soon

@raulcanela5669 Жыл бұрын

@@MikeD4 I m currently programming that one