Rocker Panel Molding With Clips

Rocker Panel Molding With Clips | 1967-1968 Mustang

Рет қаралды 55,957

8 жыл бұрын

Bill shows you how to install this Rocker Panel Molding with Clips on your 1967-1968 Mustang. A beautiful direct-fit reproduction of the original, these moldings run along the exterior of the car just below the door. Includes mounting clips for a stress-free installation.
Get these rocker panel moldings here:
www.cjponyparts.com/rocker-pan...
Check out our install guide for written instructions:
www.cjponyparts.com/resources...
Check out more Rocker Panels & Moldings from CJ's:
www.cjponyparts.com/mustang-ro...
Subscribe to CJ Pony Parts on KZfaq here:
kzfaq.info_c...

Пікірлер: 21

@paulleonard2211 3 ай бұрын

Bill is going to be missed. He always has great clear videos.

@miriamgillingham7115 4 жыл бұрын

great vid...you could touch up the hole with paint or spray rust proofing into the sill.

@mcinkyt 8 жыл бұрын

Install the front and rear clip then snap a line for the rest

@kennethmalnar4914 9 ай бұрын

Thank you, good video

@bazooka1312 3 жыл бұрын

I bought these to fix them on my 1970 fastback

@gpaulwelch7127 3 жыл бұрын

I would say move the first one on to 3 inch an then do the 13 inches because if someone welded up the holes its hard to drill them

@Bmackie731 3 жыл бұрын

FYI, do not rivet in the top and then drill outthe bottom as suggested. HIGH likelyhood of breaking the clip if you're not very very careful.

@charleyhelvy8529 3 жыл бұрын

yes, a better idea is after drilling the top hole hold the clip in place with a small screw, mark the bottom take the clip off than drill it.

@72Stiles 4 жыл бұрын

Wish someone made these for the 67 Thunderbird

@Bmackie731 3 жыл бұрын

Are you using the 1/4" drill bit to drill out the front stud hole?

@novaguy509 Жыл бұрын

What about painting the freshly drilled holes. Won’t the rocker panel rust out without sealing the drilled holes?

@diyautoschool Жыл бұрын

The rivits will seal the holes when you put them on.

@kepaloha 8 жыл бұрын

Great Video, one question, the holes to be drilled below the door does the same measurements apply to a 1965 mustang?

@Zerogivengarage 8 жыл бұрын

+kepaloha I would guess they are different on the 65.

@fabiandorian1224 2 жыл бұрын

instaBlaster.

@davidlaraman7443 3 жыл бұрын

So where do you get the tool to install the pins like a staple gun ?

@Bmackie731 3 жыл бұрын

Its a rivet gun. Amazon, local hardware or big box store.

@abbylx 6 жыл бұрын

did the fastback have this?

@myfriendpete Жыл бұрын

Yes

@andrewfleming3687 7 жыл бұрын

I bought these.......the quality is not great, one of them was almost half inch shorter but you get what you pay for I guess. Dont replace old stuff with new stuff if its not in that bad of shape.......

@diyautoschool Жыл бұрын

The quality SUCKS DONKEY D's... These moldings are pure junk.. I would suggest to anyone to search and find some oem factory ones.. PURE TRASH!