3 Ways to REMOVE PVC Pipe From a FITTING

Рет қаралды 384,978

2 жыл бұрын

DO you have a broken pipe you need to replace BUT want to save the fitting? Well, you're in luck, today I'm going to show you 3 ways you can take out the broken pipe WHILE keeping the fitting in one piece!
▶️ Recommended Playlist: • DIY Plumbing Tips and ...
🔔 Subscribe for more AWESOME plumbing videos: / @rogerwakefield
⭐️ Become a Member TODAY: / @rogerwakefield
________________________________________________________________________________________________
✅ Connect with me:
Instagram - / _rogerwakefield
Twitter - / _rogerwakefield
Tik Tok- / rogerwakefield
Reddit- / rogerwakefieldposts
LinkedIn - / rogerwakefield
✅ For business inquiries contact me at contact@rogerwakefield.com
________________________________________________________________________________________________
🔴 Links:
Check Out My Merch! - tuberturds.creator-spring.com/?
My Free Mini-Course- bit.ly/rogersfreeminicourse
My Networking Secrets That Grew My Plumbing Business FAST - bit.ly/rogersfreeguide
My Recommended Plumbing Study Guide -amzn.to/2RgYEn5
________________________________________________________________________________________________
Thanks for watching! I'm Roger Wakefield, The Expert Plumber, and welcome to my channel. On this channel, it's ALL about plumbing. We play games, we experiment, and we have FUN here, talking and learning about all things plumbing!
____________________________________________________________________________
🎥 Gear We Use:
Coolest Clock Ever - amzn.to/31CjLkW
Main camera - amzn.to/2RCyj1F
Lens for main and Second cameras - amzn.to/2SM7
Second camera - amzn.to/2SdzfdQ
My microphone - amzn.to/2FEvN8s
XLR Interface - amzn.to/2RDqskj
Wireless Lav Mic - amzn.to/2HenuRp
Tripod to hold our camera - amzn.to/32aI7Dj
Our studio lights - amzn.to/2Zv2R6O
*NOTE: This description contains affiliate links that allow you to find the items mentioned in this video and support the channel at NO COST TO YOU. While this channel may earn minimal sums when the viewer uses the links, the viewer is in NO WAY obligated to use these links. Thank you for your support!

Пікірлер: 362

@RogerWakefield 2 жыл бұрын

Y’all I know heat gun is the better tool! But I wanted to have some fun today. Have you tried this trick before?

@marionoliver6004 2 жыл бұрын

Never tried a heat gun..might try it one day

@danielb7341 2 жыл бұрын

My mentor used his map gas torch to soften the pipe

@jordanwhite6098 2 жыл бұрын

ABS is the tricky one.

@alejandrosantillan3783 2 жыл бұрын

@@jordanwhite6098 that stuff is the work of the devil, always makes me cringe when I see it 😂🔥

@jacobcdumas 2 жыл бұрын

with toilet flanges I tap around the center of the flange with a hammer and progressively hit harder before I cut the reliefs. sometimes they breaker the glue joint free. if not I cut my reliefs and pry on the peices first. my trick is not to pry on the the pipe or fitting I'm trying to save. I do a lot of this and have a pretty good success rate as a service plumber. I have some good tricks for removing copper male adapters and galvanized pipe from cast iron. just takes patience and thinking out side the box when in tight confinement. detection and location are a specialty of mine also. thanks for the videos boss. keep them coming.

@BaconJD420 2 жыл бұрын

Always make sure you leave an open can of glue that is super flammable right next to the pipe on fire

@dshudson Жыл бұрын

I learned right away not to do anything this man says

@scignosis 11 ай бұрын

Thanks, going to the store tomorrow so I'll grab the glue

@davidelliott5843 10 ай бұрын

Put a blow lamp flame over the pot and you’ll get a mild pop. It won’t explode but it’s a great reminder to put the top on.

@AllThingsAudioHTX 3 ай бұрын

Don’t forget to wear your green nitrile gloves when working with fire!

@CastilloAJohn 2 ай бұрын

The real tips are always in the comments thanks

@trappervirginia1368 2 жыл бұрын

As a 3rd generation plumber who has done all of these ways I will warn of #3 which works great on large diameter pipe like 12”-16”. Don’t use this method if pipe was glued together in last week or so PVC glue is explosive if contained. The vapors are heavy and will settle in pipe. Trust me on this I have seen what happens. Several hundred feet of pipe was turned into shards of plastic. It was not pretty and if someone had been in ditch they would have died. If pipe is aired out works great.

@treacheroustiger5571 2 жыл бұрын

I love that you keep the set attempts in. Its for beginners to see. Even an experience professional can make mistakes. But, the best learn from them and improve because of them.

@luyandalunxumalo5687 9 ай бұрын

I love how honest you are and show us even your failed videos

@trishnichols8793 6 ай бұрын

Because "I" am the DUMMY that always tries to take the easy way and $(r3w it all up!...

@jacksplumbingvideos7147 2 жыл бұрын

I always put a hose clamp on the fitting hub so it does not crack when I remove pieces of pipe.

@raymondchambers8325 2 жыл бұрын

Good idea.

@tphvac87 2 жыл бұрын

Studpack did this same test on the way to remove pipe from a fitting as well, good job Roger!

@barrylivingston517 2 жыл бұрын

Thanks for sharing your experience. I have done the sawz-all with a hammer and screwdriver in the past. My experience with this method was like yours. I really like the Ram bit for drilling out the pipe from the fitting hub, but I've never heard of heating the pipe still glued inside a fitting hub. That's a fantastic idea, and it looks pretty clean. Thank you

@josecarbajal6706 2 жыл бұрын

Try the reed fitting savers

@nolantanaka565 2 жыл бұрын

@ Jose Carbajal I heard those are the best but they are expensive

@laoboyardee1 2 жыл бұрын

I'm a construction plumber and I have all pipe sizes socket saver from 11/2 to 4". When I was a apprentice I worked with a foreman who didn't know about these bits and he made me dig under a tee that tied into the city sewer because it was broken inside the top of the hub. The tee was still good. The trench was about 3 feet deep and about $60 dollars in fittings. Years later, I worked with a different foreman and we was in the same situation. Broken pipe in the hub on top of the San tee. But this time I didn't have to dig 3 feet down. The foreman had a set of reed ram bits and that's where I learned to use the ram bits and I've used it numerous times since then. Framers on the grade all forklifts constantly break our risers for sewer pipes. I have the raptor brand socket savers from Ferguson. They are not as nice as the Reed ram bits but way cheaper and they work fine for me. Thanks for the video Roger. Perhaps you saved some people from digging unnecessary trenches in the future. Haha.

@tannerwest6823 2 жыл бұрын

Yea the Raptors are cheap but they still work. Have to break mine out from time to time. I don't use them enough to have a real nice set

@AhernMatthew22 Жыл бұрын

Im 4 months into a plumbing apprenticeship and your videos are great, i love my new profession altho ik their are gonna be some growing pains

@isaaczamora5626 2 жыл бұрын

Great job Sr. I did this in those 3 ways. Another tip: I use a heat gun also getting a good and clean fitting. Most part of the time after extraction use a pipe to keep the shape while fitting still hot

@timkourniotis861 2 жыл бұрын

Very cool. The only thing I would've done differently on the last one is use an acetylene torch on a hole saw bit roughly the same size as the inside diameter of the PVC. That way you're limiting the heat to the inside of the fitting and not risking compromising the fitting or giving out unnecessary fumes. Great video!

@gsftom 2 жыл бұрын

I need to do this next week. Excellent timing!

@asm101 2 жыл бұрын

Fantastic video! It's definitely targetting every possible audience...awesome..just awesome

@compactc9 2 жыл бұрын

I've had to use the saw in the pipe trick on a central vacuum system once, it worked great and saved me from having to open up the drywall.

@colinhoffpauir9892 2 жыл бұрын

I'm an apprentice plumber and I almost have a year under my belt, we were doing a sewer line tie-in for an added bathroom in a garage and used a map gas torch and it worked surprisingly well.

@JesseWright68 2 жыл бұрын

I bet that smelled great.

@bryancansdeez4453 Жыл бұрын

Thanks I'm about to do the same

@anthonywyckoff2964 2 жыл бұрын

You didnt comment about the setting fire to a fitting when there is active methane in the system, which is highly explosive. This is why i never you this method u less on a bench not connected to the system. Im not disagreeing with you just asking if you have ever used this method when the fitting is attached in a active system. I love your work and how you teach us all. Thank you Roger

@tightropehikes 3 ай бұрын

Brother chill. He said residential service

@mousetoad7040 2 ай бұрын

@@tightropehikesMethane gas can form in residential sewers too. That’s why even residential houses hoses have traps to prevent sewer gas smell and explosive buildup. I’m no plumber, but I have experienced sewer gas buildup in residential buildings when a drain wasn’t used and the trap dried out. Open flame method might be ok on a work bench but I’d hesitate to use it on a live sewer system regardless of residential or commercial. Sewer gas (methane) is there

@tightropehikes 2 ай бұрын

@@mousetoad7040 plumber here. I wouldn’t If anything the p-trap would make the buildup more than no trap. This is a non issue for residential plumbing unless the cities infrastructure has failed to a very large degree, meaning entire streets or blocks are non functioning. Just take my word for it

@zerovalue5106 2 жыл бұрын

The reed pipe tools clean ream extreme is an excellent tool. Works for drainage and pressure. If you do more than 2-3 cut and peels a year it’s worth it’s weight in gold. I have the 2” and the 4”. Recently bought the 1 1/4” for a specific job. They’re worth it. I’m going to have the full set eventually just getting them one by one.

@raymondchambers8325 2 жыл бұрын

If I dry fit, how tight is it?

@pawdre5151 2 жыл бұрын

Can agree it’s awesome just wish it was a little bit less expensive. But then again it is a quality CNC machined part that you’ll never buy again.

@derrickquinn8383 Жыл бұрын

Your method of the jigsaw worked! Thanks for sharing!

@WABoothPlumbing 2 жыл бұрын

Socket saver is my go to tool for something like this. Ive broken so many fittings with the sawzall screwdriver method. And ive always been scared to have an open flame in or underneath a house or building. Just not willing to risk it these days.

@Chris.Rhodes 2 жыл бұрын

Stud Pack did a video on this it was called "Heat Gun VS Hole Saw - Removing Glued PVC/ABS Pipe Fittings" it was a very informative video, and Got2Learn did a video as well, KZfaq has surprisingly taught me how to do my job better a lot of times! Thanks for all the work you put into your videos man! 👊

@bdblazer6400 2 жыл бұрын

in germany we use HT or KG ROHR systems with a rubber seal. Slip it together. Done.

@raymondbrecheisen 9 ай бұрын

Did a burnout at work on a riser and it worked perfectly. Learned how to and about it here.

@b.powell3480 2 жыл бұрын

Great video Roger ! I usually use the torch or heat gun, heat gun is safer than the flames, however!!

@Blackbypopulardemand305 2 жыл бұрын

I used to carve it out. Last 5 years I use a heat gun and pliers. 100% success rate

@philliptyner8394 2 жыл бұрын

Thanks!

@Bukinbronco88 2 жыл бұрын

Thats what I do. Or a torch

@CyFi6 Жыл бұрын

Thanks I'm going to try this next time I have full access to a large pipe that's securely fastened to a workbench

@RogerWakefield Жыл бұрын

Well good luck!

@truetildeath 2 жыл бұрын

Hey Roger! This week i’ll be starting as a service plumbers helper for a plumbing company. I’m really not sure what to expect besides what i’ve watched from some of your videos over the years. Do you have some advice you could give me?🙏🏻

@jammiewolf6336 2 жыл бұрын

Love the videos Roger, they are very helpful and interesting keep up the good work

@daowara85 2 жыл бұрын

Can I be a good plumber like you! Thanks for your technique.

@raymondborror6996 10 ай бұрын

Thank you, Roger. Very informative.

@RogerWakefield 10 ай бұрын

Glad you enjoyed it, what was your favorite part?

@billy6166 10 ай бұрын

Thanks very helpful!

@raybenitez503 2 жыл бұрын

The heat gun works great for me, especially when its very cold and the pipe tends to break easily. Thanks for the video.

@billychandler1900 2 жыл бұрын

Ram bit is the best way, been a plumber for 28 years in NC.

@ronlovell5374 2 жыл бұрын

1:23 into the video 🤣 I've had to do this many times. My favorite method is heating a holesaw with a heat gun or torch that fits snug inside the pipe I'm trying to remove. This method is super clean and safer than igniting glue, putting the heat exactly where i want it, especially if there's crazy sewer gas...

@tacklebox6239 2 жыл бұрын

Master plumber here, I’ve seen that done on other you tube channel, I tried it on ABS but didn’t work out too good

@darinsmith9468 2 жыл бұрын

I've done that very thing on pool plumbing multiple times and it works like a charm on PVC.

@nolantanaka565 2 жыл бұрын

@ Tackle box yup was about to say that none of these methods will work on abs. Maybe if lucky the first two might. Abs tends to just melt and bind together again when cut with sawzall

@taytaytheoriginal4850 2 жыл бұрын

Socket saver is a must have, I actually use it for other things, like when I’m roughing in urinals, I’ll glue the 2” into the wall, and once the drywall and paint is done, I’ll use the socket saver on the two inch pipe, so that urinal flange fits perfectly 1/2” in from the finish wall. Whenever we are doing underground and the concrete guy snaps the pipe, after THEY chip some concrete around where they snapped it, I’ll use a socket saver down below the concrete to put a coupling on. OR if you’re pipe isn’t quiet roughed into the wall, you can save the pipe down low enough to get a 32nd bend or whatever and squeeze that into the wall

@ianhall622 2 жыл бұрын

iv also used the hole saw method and a heat gun and iv seen it done with a torch as well but you need a peace of pipe to put in to keep it round after you remove the old one and its time consuming as well

@MasterHustler 2 жыл бұрын

Great video bro. An oscillating saw works good also.

@wiseandhumble2470 2 жыл бұрын

I've used a hole saw before, just gotta be sure to use the correct size and not to go to deep

@jason48100 Жыл бұрын

Great information!

@ImportDomestic2006 2 жыл бұрын

As I’m watching what you’re doing. The first idea seems to be an excellent idea. however when trying to perform that type of repair most of the time you’re in a tight spot which will not allow you to use a salsa or any type of cutting tool since you will be in such a awkward position. I have personally used your second method of saving a fitting. There’s actually a company that sells a kit with the different sizes for your drill. They have two separate styles of kit for cutting a PVC pipe and having a perfectly round male and a female removal kit as well. Know using fire for removing PVC I’ve never utilized that method. in my opinion it seems dangerous depending on the individual situation. You never know if there’s any methane gases that have collected in the pipe unless it’s a new construction.

@towely Жыл бұрын

Just do like I did by having a contractor you hired ride a heavy piece of tracked machinery over your septic mound... busted all the pipes up real nice for me... :-|

@nicholascasiano8479 2 жыл бұрын

In a perfect setting with a vice so love to see this on a jobsite I give you 20/80

@kevinhill5596 2 жыл бұрын

Excellent!!!

@kevinhinson994 2 жыл бұрын

I don’t deal with plumbing pipe at all but I do deal with pvc conduit quite often I wonder how the fitting saver would work with that even us sparkeys goober once in a while and it would be nice to save the fitting

@Mr.S_BuildsThings 2 жыл бұрын

Socket saver for the win!!!

@Karisma77 6 ай бұрын

Great tutorial thanks so much!

@RogerWakefield 6 ай бұрын

You are so welcome!

@BetterThanUnson 2 жыл бұрын

Another banger Roger, keep it up

@RogerWakefield 2 жыл бұрын

Much appreciated Ye11owCake

@eduardomunoz430 2 жыл бұрын

@@RogerWakefield I know sometimes you do those plumbing vs other trade videos can you do one with plumbing vs automotive technician on your opinion on the auto industry.

@RogerWakefield 2 жыл бұрын

noted!

@mypointofblue5260 4 ай бұрын

Great info! Thanks for sharing!

@RogerWakefield 4 ай бұрын

Any time!

@jaredv7109 2 жыл бұрын

Roger. If I use the fire method on a two way clean out. Should ball stop the open side going on the opposite run? i.e melting home side, stopping city side. or city side, blocking home side. In preventing some sort of backdraft leading into a home, or traveling down the city line. I'm sure methane build ups can be troublesome. Thanks for the video!

@MrBruce0777 4 ай бұрын

Method #2 looks the best that is if you have the right saw blade. Thanks for the went wrong attempts.. I visit the wrong way once in a while LOL..

@dshudson Жыл бұрын

You just showed me three ways not to do it.

@zichuckbrian7020 2 жыл бұрын

We have been doing this in Nigeria for long that I can't even remember...thanks for sharing this to the public tho

@mastersfan04 2 жыл бұрын

I use the socket saver bits. Most DWV pipes in my area are ABS. Never tried the heat method

@theconservativeplumber Жыл бұрын

Nice gloves Roger. They look just like mine😁

@micahvanella2938 2 жыл бұрын

I'm trying to do the opposite. Previous owner glued on the connector to the ptrap to the stub out under the sink and there's very little real estate to work with coming out of the wall. Going to try to take off the old glued fitting but save the pipe and get a marvel connector.

@irvintrevino9361 2 жыл бұрын

I am an apprentice and I have a doubt, that does not cause problems when the pipe is in operation and the gases come out of the drain after you put fire, could it be something dangerous?

@libsrcrazy9634 Жыл бұрын

Hi. Regarding method 2. Can you go into detail about how you clean the inside of the elbow after you grind the pipe out. Do we need to remove all of the purple thats in there? With what? What if the bit scratched or gauged the inside of the elbow..is that ok. Obviously im not a plumber. Just a home owner. Id had a plumber do some work in my basement to my drain pipes and its leaking at the connection. It seems he didnt push the pipe into the elbow deep enough. Im trying to figure out how to fix it. Thanks

@aschtonlail744 2 жыл бұрын

I need this

@jbird78 Жыл бұрын

Haha, love showing the fail attempts makes it real...and funny as shit!

@DukesCreate 2 жыл бұрын

Hey Roger, I think this is a great video and very informative. I do have one question, do you think the fire trick would work on pipe that is 20 or 30 years old? Thank you for all the great videos!

@PARKERBROTHERSPLUMBING Жыл бұрын

Yes, assuming it's pvc

@jamieplumber 2 жыл бұрын

Title should be “how to burn a house down” lol

@iceman846 2 жыл бұрын

I use a torch and heat the inside of the pipe like you are toasting a marshmallow, when it turns a light brown color it twist out easily. Works every time.

@wheelitzr2 2 жыл бұрын

"Ways you can remove an old fitting, don't try this at home I am a trained professional", he says while he has the fuel source less than a foot away from the burning fire.... 🤣

@Spelter 2 жыл бұрын

I think that's why he inserted the fart sound 🤣

@keithv708 2 жыл бұрын

Nice

@deweybewey 2 жыл бұрын

Had to do the first trick with over 20 toilets flanges to offset them all 😂👌🏼 became an expert that day 💪🏼😎

@BobsPlumbingVideos 2 жыл бұрын

Heat gun Roger👍👍.

@user-pe6oz5ok5q 3 ай бұрын

A pvc fitting saver: saves time and money 😅

@RogerWakefield 3 ай бұрын

And saves brain cells 🤣

@ThoraxThePlumber 2 жыл бұрын

1:23 there’s the real roger love hearing real trade talk 😂

@Guyuk1 11 ай бұрын

Hi, thanks for the video. Whats the name of the drill bit a 3:43? I'm searching for it online and can't find it.

@XSpImmaLion 2 жыл бұрын

Might be wrong on this, but it looks like a good case for a plaster heat gun and an ultrasonic knife. Only problem is the ultrasonic knives usually have a very short blade, and you know, very easy to cut the whole thing apart... xD

@jakemichels6533 2 жыл бұрын

Instead of using the glue to heat up the fitting I take one of my hole saws and I find the one that’s closest to the ID of the pipe. Heat up the hole saw to the point where its near red hot and stick it in the pipe for 5-10 seconds then peel out the pipe from the fitting. No smoke like with lighting the glue on fire

@calebmcdaniels8535 Жыл бұрын

Very good video

@RogerWakefield Жыл бұрын

Thanks

@re-saledtxusa549 2 жыл бұрын

Torch, screwdriver and channel locks, easy cheezy!

@dustinjohn915 2 жыл бұрын

Ram bit is the go to but I’ve chipped out many of fittings. Not sure why he made so many cuts. I just do two cuts about an inch apart with the sawzall or sawzall blade. Then if you chip it right the rest will come out in one piece.

@SwiftKickIt615 2 жыл бұрын

On service calls when I get a broken flange I usually use my Milwaukee M 18 hacksaw. 8 inch flat head screwdriver and a hammer. I charge by the hour so that’s mainly why I do that. Prep work is key

@jbirdtheowl1037 Жыл бұрын

I like using the point on the paint scraper to get in between the pipe and fitting, then once i have a little gap using the good ol flathead

@eddieromero8805 Жыл бұрын

I like the 3way😎

@ThiPham 7 ай бұрын

Great way to remove PVC pipes

@Aepek 2 жыл бұрын

For heat Roger, I like using a heat gun and needle nose pliers. Pipe rolls out like opening old can of tuna or sardines. Just remember ppl, don’t use heat on ABS, or you’ll melt it and have a mess😉. Another way that works great that most have, hole saws. Use a hole saw same size and it’s similar to fitting saver bit/saw, but everyone ibis has hole saws😅 Cheers✌🏻

@kaitheramptruckman7539 2 жыл бұрын

Heat gun work the same?

@joshcowart2446 2 жыл бұрын

The best method is to use an old hole saw. I actually learned this method from the got2learn channel. You get a hole saw that fits as close as possible to tue inside of the pipe. Get it red hot with a torch then stick it inside. Use vise grips to hold it at a certain depth. You can pull the old pipe out with your hand this way.

@Chris.Rhodes 2 жыл бұрын

Yeah I seen that video. Stud Pack also did a really good video it was called "Heat Gun VS Hole Saw - Removing Glued PVC/ABS Pipe Fittings" if you haven't watched that yet, they are a great channel to watch. Son and father team and they do excellent work, and it's a great family friendly channel. I've learned a lot from them, and Got2Learn at the same time. Although G2L hasn't posted a video in a while.

@joshcowart2446 2 жыл бұрын

@@Chris.Rhodes I watch their channel. They’re one of the few handyman channels that actually does plumbing properly. They didn’t do the hole saw method I use in that video. They used the hole saw like a fitting saver bit whereas I heat it up

@volvo09 2 жыл бұрын

The fire is a neat trick. Some patience and a heat gun will probably work as well? May be safer in a combustible area at least, or if you have a backdraft or chimney affect in the pipe from the vent. Would hate to burn a house down lighting the inside of a pipe on fire too far up to see!

@humbertomacias3239 Жыл бұрын

I've been playing 3/4" - 1.5" late and it's fun. True doesn't always work but heating it does. I'm planning to fix a 6in chiller pipe in a few days, Pray for me 🙏🍻

@leach713 2 жыл бұрын

When I chip them out I like to cut it twice and apply primer to them before chisel them out , or I used torch and heat it out

@bryanjk 2 жыл бұрын

As an electrician, I might get the fitting saver. Might come in handy someday with a conduit fuck up.

@williamboswell6834 7 ай бұрын

Instead of the sawzall and screw driver I've used a half inch wood chisel and hammer. Thanks for the tip on using fire. I had seen it done before but I needed a refresher course.

@RogerWakefield 7 ай бұрын

I do NOT reccomend the fire method in MOST cases...be VERY careful with that one

@williamboswell6834 7 ай бұрын

@@RogerWakefield I did start off trying to fire method, however the whole fitting started to flex and bend, so I backed off of that and went with my old standby. Actually more of a combination of the two as the space I was working in was incredibly tight.

@CuntryRebel 2 жыл бұрын

I’ve used forstner bits

@brentbeatty4171 Жыл бұрын

I like your presentation :-)

@RogerWakefield Жыл бұрын

Thank you!

@ryanpflughaupt4726 2 жыл бұрын

Any issues with "following manufacturers instructions" and warranty work?

@zachammel6281 2 жыл бұрын

Iam always having to do this for flanges

@wtfisdat6382 Ай бұрын

hole saw bit (like you'd use on a door). choose one smaller than your fitting, hit it with heat til it glows and slip it into your pipe. Fantastic at controlled softening, no open flame and peel the pipe right out with whatever plier device you prefer.

@ChrisMorton Жыл бұрын

You can use boiling water too. Put fitting in pot of boiling water and edge it out using flat steel piece. It is thermoplastic it softens when warm.

@douglaswatters7303 5 ай бұрын

one thing to do this on a nice clean workbench with no obstructions around you, quite different to do this under a building laying in a dirt trench that took you three days to dig out while laying on your side and barely enough room to move.

@sheerziggy 2 жыл бұрын

I used to do burn outs before I got a socket saver set.

@jimshaffer3610 2 жыл бұрын

I used to do it at work score your pipe with the saw like you said and then take a heat gun or a blow dryer and heat the pipe on the inside then take a pair of pliers and turn the pipe n-word and a rose around a circle and pulls away from the glue fitting then you can pull the piece of pipe out

@runebooke 2 жыл бұрын

*Pipe Burning* "If your under a house......" Yeah, you'll burn the house down lmao. I imagined a plumber being in a crawl space.

@syreplays5079 2 жыл бұрын

That fire trick was pretty soivo

@SaltyTubers 2 жыл бұрын

Appropriately timed this close to tax day in the US. Always feels like the tax man is trying to remove pipe from my fitting by force!

@gussygoro2469 8 ай бұрын

This video is unintentionally hilarious. Don’t set your plumbing on fire.

@bobbymunoz9778 2 жыл бұрын

Ok I’m convinced roger or KZfaq is watching me .. I’m on my tool box doing just this watching a podcast and this comes up

@LibLibertyLibertarian Жыл бұрын

I use a combination heatgun & Sawzall, meaning I cut a slit into the pipe heat the area and roll the pipe off heating as I go. A good tip is to use a wet rag to keep the fitting cool as you roll to prevent it from deforming

@lowdown5150 Жыл бұрын

Nice!