Roland SPD-20 - Battery Replacement

Рет қаралды 16,521

3 жыл бұрын

You are the owner of a SPD-20? You see the Battery Lo on power up?
Or worst, the Ran test ERR? Well, this step-by-step will show you how to save 100$ in repair and how to replace the CR2032 Battery yourself without damaging your precious machine.
#SPD20 #Battery #Repair

Пікірлер: 55

@Combo_Times 3 жыл бұрын

Thank you verrrrrrrrrrry much for your beautiful, interesting and soooooo useful video, man)) All The Best = }

@ThePhilStudio 3 жыл бұрын

Thanks to you. It's a pleasure.

@bladewolling4947 Жыл бұрын

Oh NO! Yet another one of my instruments that I've had in storage for 15 years that might need a new battery. Thanks for the reminder so I can allocate time to change the battery before assuming that the SPD-20 will be ready to go when I need it (which is soon).

@ThePhilStudio Жыл бұрын

Ahah it sucks but it has to be done from time to time. Like after some years :P

@jscan Жыл бұрын

fine little tutorial! I'm attempting to open my SPD-8, whose case seems to be very similar, but I'm having a lot of resistance pulling the back off and don't want to break it! My battery is probably fine but I will check it when open and my goal is to modify the circuitry (pad breakouts and USB adapter) as well as paint the case. My question: does one have to put considerable force to pull the back from the unit? Yes, all externally visible screws have been removed and I seem to have separation of case all around between 5 -15mm on any given side (less usually on the rear side), it seems there is some clip holding the case together in the middle rear, but nothing visibly apparently peaking through the separation. Appreciate anyone's comment/assistance!

@ThePhilStudio Жыл бұрын

Not 100% sure but I think there's 2 plasic clips on top left and right of the unit. Give it a gentle pry with a small flathead screw driver. Let me know how it goes. Maybe a plastic credit card would be better to unclip.

@DICARLOPRODUCTIONS 3 жыл бұрын

Thanks!!!! :)

@ThePhilStudio 3 жыл бұрын

Glad to see it helped you!

@hemantabarik6899 3 жыл бұрын

Thank u sir

@ThePhilStudio 3 жыл бұрын

You are welcome.

@rupamupadhyaya654 3 жыл бұрын

Thnks sir

@ThePhilStudio 3 жыл бұрын

It's a pleasure.

@rupamupadhyaya654 Жыл бұрын

@@ThePhilStudio where from u sir

@hichammohaddab575 Жыл бұрын

please how to regoler err analog when i get it on i cant do it

@ThePhilStudio Жыл бұрын

Make sure your power supply is the right one. It is supposed to be 12V AC (this allows to make the +5V , 0V and -5V.)

@andrestecnic1 3 жыл бұрын

hi my octapad says (analog base error) do you know the solution? Thanks.

@ThePhilStudio 3 жыл бұрын

From what I red, this message could occur if you strike a pad while turning on the power. If you press any button, the display error should disappear. If it doesn't disappear, I guess there is a defective pad (piezo).

@mkmoni588 2 жыл бұрын

how to change rubber change on spd20

@ThePhilStudio Жыл бұрын

You will need to open the unit, remove all the piezo sensor and I don't recall any screws. Let me know how it goes.

@mayank8490 3 жыл бұрын

Please tell me if I restart octapad will all my patches deleted ..???

@ThePhilStudio 3 жыл бұрын

A factory reset would probably delete all your patches. Make sure they are saved somewhere before doing so.

@horacioperez3779 3 жыл бұрын

Hello, something strange happens with my octapad, I program it, save it, and then next day it's back to normal, do you think it is because of the battery? Or what do you think it is?

@ThePhilStudio 3 жыл бұрын

Most likely the battery. You should check it with a mutlimeter. Or just replace it.

@horacioperez3779 3 жыл бұрын

Thanks for ur quick response,... What does the battery do? Or what is it for?

@ThePhilStudio 3 жыл бұрын

@@horacioperez3779 it's there to keep user's settings in memory.

@Isaiasvargas834 11 ай бұрын

Amigo. Se reemplaza así apagado el Octapad o ensendido?

@rupamupadhyaya654 Жыл бұрын

Thnks which battery is good plz reply

@ThePhilStudio Жыл бұрын

The battery is a 3V lithium coin cell: CR2032

@rupamupadhyaya654 Жыл бұрын

@@ThePhilStudio thnks brand name plz

@mkmoni588 2 жыл бұрын

How to change 8pad on roland spd20

@ThePhilStudio 2 жыл бұрын

You can replace the Piezo fairly easily, see 3:50 of the video. There are 2 solder on each piezo, make sure you solder them the same way.

@aniljangrapercussionist8715 2 жыл бұрын

Sir what is the maximum and minimum battery level Mean, at what % level we should change the battery

@ThePhilStudio 2 жыл бұрын

A CR2032 is usually 3,3V and considered dead or to be replaced when it reach something like 2.8 - 2.7V

@aniljangrapercussionist8715 2 жыл бұрын

@@ThePhilStudio Thanks a Lot Sir🙏🏻

@ThePhilStudio 2 жыл бұрын

@@aniljangrapercussionist8715 You're welcome, do not hesitate if you have any other questions :)

@aniljangrapercussionist8715 2 жыл бұрын

@@ThePhilStudio 🙏🏻😊

@xzavierortiz5284 2 жыл бұрын

@@aniljangrapercussionist8715 I have a spd 11 but wont power on

@audigerman2226 11 ай бұрын

Hi.. How may I Buy this Used Roland SPD drum pad.. please 😊

@ThePhilStudio 11 ай бұрын

Unfortunately, that Roland doesn't belong to me.

@mkmoni588 2 жыл бұрын

are you octapad servicing engineer? Please tell me

@ThePhilStudio 2 жыл бұрын

If you really want to have your octapad fixed, maybe we can have an arrangement.

@goldenbeatmaker5219 3 жыл бұрын

I want spd20 pad please help me

@ThePhilStudio 3 жыл бұрын

I'm not providing any parts for this product unfortunately. I highly recommend that you contact the manufacturer for further help.

@biveksilwal8800 2 жыл бұрын

Hlw sir I am from Nepal 🇳🇵 can you provide me spd20 pad

@ThePhilStudio 2 жыл бұрын

Hi, are you looking for the rubber pad? The whole unit or simply the trigger which is a piezo? Thanks!

@dineshkoli6873 3 жыл бұрын

Hello sir spd 20 pad give me please final price sir selling

@ThePhilStudio 3 жыл бұрын

Hi, unfortunately, I am not selling anything.

@ozgurcakrlar4504 2 жыл бұрын

Marhaba benin spd20 sesler efekli geliyor birde kesiliyor bana yardımcı olabilirmisiniz pil arızasını acaba sizden rica ediyorum lütfen bana yardımcı olurmusunuz

@ThePhilStudio 2 жыл бұрын

Ünitenin açılıp açılmadığını söyleyebilir misiniz?

@ozgurcakrlar4504 2 жыл бұрын

@@ThePhilStudio evet açılıyor açıldıktan sonra kit ve trampetten karisik sesler geliyor

@goldenbeatmaker5219 3 жыл бұрын

Sir where are you from

@ThePhilStudio 3 жыл бұрын

The PhilStudio is based in Canada. Where are you from?

@goldenbeatmaker5219 3 жыл бұрын

@@ThePhilStudio sir i want to take a new spd20 tottal percussion pad will you get it from me?

@goldenbeatmaker5219 3 жыл бұрын

@@ThePhilStudio sir i am from india (punjab)dist.Hoshiarpur