Rolex Bracelet Link Removal and Sizing for Submariner

Рет қаралды 185,757

4 жыл бұрын

This method can be used on any modern Rolex watch with an Oyster Bracelet or Jubilee bracelet including the Submariner, Sea Dweller, Datejust 41, Daytona and GMT Master. Please take care, but with these instructions, you can successfully re-size your watch without visiting a dealer.
Follow this link: linktr.ee/theenglishwatch
Link directs you to my Merch store, Amazon Store, Instagram, Facebook, Website, Email, Linkedin, etc.
Music by www.bensound.com

Пікірлер: 131

@manomanarven 5 ай бұрын

Perfekt. You think a Rolex Dealer make this like you?NEVER. He scratched me before. When the screws after work looks like new, than its mean perfect work. Do it yourself. Than you know what you are getting. Mister your work is 100 % perfect. I like it❤

@EdwardMeinert 2 жыл бұрын

Hello! Just wanted to let you know that I studied your video a few times, did exactly was you said and you saved me a trip to the watchmaker. Thanks!

@edwardpate2288 2 жыл бұрын

Great video, and I now have the confidence to size my Submariner bracelet on my own. Thank you

@dashingcarp Жыл бұрын

Thank you! Was able to size my GMT carefully and confidently following your tips and steps!

@tomlabarbara6277 5 ай бұрын

Clear and concise tutorial! Just resized my submariner following this video, thanks for uploading

@ultragroove1 3 жыл бұрын

Great video and explanation. Really appreciate the tape trick. I’ve been apprehensive about removing a link but with your how-to and zoom of the screw detail, I’m going to proceed. Thank you!

@stevel.1685 7 ай бұрын

Brilliantly done instructional video. Loved the first part about the Glide Lock which my Rolex dealer sales rep failed to mention.

@jhcowatchinglifestyle 4 жыл бұрын

That tape tip is huge for those hyper-polished links!!

@sinjon 2 жыл бұрын

Great video. Great tip using the tape. I just bought some to resize my new Railmaster Trilogy. Expensive stuff but if it keeps me from scratching my bracelet, it’s worth every penny.

@bigslacker666 Жыл бұрын

Nice, great vid. FINALLY acquired an SD43 and fitted it to my wrist with the same method.

@sunglee2048 Жыл бұрын

Thank you! Just saved me time and money doing this on my own. Good day to you.

@james_ross 4 жыл бұрын

Nerve wracking, but worked perfectly thanks. Nice to enjoy the watch, now it fits properly again.

@zackw.9793 3 ай бұрын

Thank you for this video. I was able to adjust without removing any links! Good stuff here!

@steveoreed Жыл бұрын

Thank you. Worked for me. Took out two links but I was sweating a bit. 😅

@djeddieo 11 ай бұрын

lol, I started the process before you posted and only JUST finished! in between, I bought better tools and waited for a good low blood pressure day!

@MarioPerez-bh2sv Жыл бұрын

Just got my Submariner and this was very helpful.

@DavidAnderson-vg6pc 2 жыл бұрын

Wonderful video - I enjoyed it. Very informative, thank you.

@djeddieo 11 ай бұрын

great video! perfect length and detail too. I am subscribing.

@chrisurgel1939 2 жыл бұрын

Awesome video, my screws were really tight. I thought I was doing something wrong. I only needed to rescrew and unscrew a few times and it came out

@Rameeet 2 жыл бұрын

Brilliant video mate!

@sparrowhawk5485 2 жыл бұрын

Well presented and thoroughly useful 👍👍

@clockstrikes21 4 ай бұрын

Gramps just gave me his Rolly and it didn’t fit. Gladly found this video and surprisingly same Submariner. After watching this I made it without a scratch. Thanks Mate. Instant sub for you

@nickgreg8068 3 жыл бұрын

Such a good video, Thank you. The tape tip is just invaluable! Also using a micro fibre cloth with the bracelet holder is such a great idea. Tip top video!

@kenstevens5462 3 жыл бұрын

@RaidenF8 8 ай бұрын

This helped me a lot, thank you so much.

@joeymj1211 5 ай бұрын

Thank you very much mate, got me fitted just right. Cheers!

@Branpanman 2 ай бұрын

Cheers for saving me a trip to my local dealer!!

@marklondonmark5657 3 жыл бұрын

Nicely done, thank you.

@markwaltos2425 2 жыл бұрын

Top level educational video. Thanks for sharing.

@alecleamus3280 2 жыл бұрын

Great tips there, thanks 🙏

@maxyanoff4676 3 жыл бұрын

Great video Buddy. Thanks

@TheWESTBURY31 4 жыл бұрын

Great vids man. Iv watched all your vids now. Looking at getting a speedy after lock dow or wait until the new one comes out. People loves rolex vids so maybe smash some reviews out on them to boost views or subs. Keep up the good work.

@TheEnglishWatch 4 жыл бұрын

Good advice. I have a few Rolex vids that I'm formulating in my head. Good luck with your Speedy purchase. Mine has been back on the wrist for a week now. Loving it.

@mariagarciagarcia5391 3 жыл бұрын

Thankyou very much!!👏🏼👏🏼

@pauldharwar1336 4 жыл бұрын

Great video. It might be worth hearing up the screw on the opposite end of the screw head to loosen any Loctite that was in there to help ease a stubborn screw. Great video and tips.

@djeddieo 11 ай бұрын

"...might be worth HEATING up the screw on the opposite end..." That's a great tip right there, and I will do that next time. Me, I put the Loctite on the thread end of the screw; seemed a neater mthod.

@aledanniel 3 жыл бұрын

Great! Thank you.

@garyb2507 4 жыл бұрын

Well done that chap!

@kayea6078 4 ай бұрын

Thank you for this video

@philipbrailey Ай бұрын

That’s great, thank you so much.

@omoniyikaye Ай бұрын

Great content just subscribed to your channel. Thanks.

@sonnyanderson3604 2 жыл бұрын

Mate your a f**kin legend Thanks for this vid😁😁😁👍

@Kuuipo 3 жыл бұрын

omg thank you!

@DeadlyDigger Ай бұрын

Great video thank you. I need to add an extra link to my submariner but don’t have any spares. What size do you recommend as they are all different due to the tapering of each link.

@Laguna2013 2 ай бұрын

Ive never seen or used tape like this. Happen to have an amazon link? Thanks!

@markusf6964 4 жыл бұрын

Very informative, thank you. A complete removal and re installation of a metal bracelet would be nice. Seeing how particular you are with the taped links, please think about a guide to show how to clean a bracelet. I'm not sure i want to buy a ultransonic bath.

@TheEnglishWatch 4 жыл бұрын

Markus F I have a video on bracelet removal. In terms of cleaning, I suggest little and often. I use a soft toothbrush and hand soap (not dish soap) as it’s less likely to affect the seals. Probably do this every few months depending on use. I always wipe over my watch with a spectacle cloth at the end of the day to reduce build up of grease also.

@danrol354 7 ай бұрын

Hi! Flatten the screwdriver slot on 400 grit so that there is no space in the screw slot 👍👍

@Honda_CRF Жыл бұрын

thanks, for such a great informative video, just 3 questions (last two specifically related to the oyster bracelet of your video): 1) any reason to not apply the loctite directly on the screw thread? 2) if I need to remove 2 links, It make sense to remove a link from each side of the bracelet, or there is a technical reason for which is better to remove both links from the same side? 3) if jI need to remove one link only, I guess it can be removed from any side, correct? many thanks!

@TheEnglishWatch Жыл бұрын

Glad you found it useful. 1. You don’t want to push the loctite through the links. This will cause contamination of the pivots. 2/3. One each side works if the balance of the clasp is level with the watch head. If only removing one link, decide which way you prefer the clasp to sit under your wrist. May be trial and error. Hope that helps.

@Jamcam99 8 ай бұрын

Excellent tips there. What brand of screw drivers and sizes do you recommend?

@TheEnglishWatch 8 ай бұрын

I use Wera screwdrivers. They’re pretty robust and better than any of the cheap ones out there. Check out my Amazon store on my website. amzn.to/3s0Xb8O

@1288liam 4 ай бұрын

Nice one. I doubt even dealers are as safe as this. They quickly scurry out of sight to do it so I've never seen them do it but Is say that they aren't all trained properly. Though i would just add a blob of 222 to the screw thread rather than the hole

@jamesgrant3812 2 жыл бұрын

I did it from the part that connects and if not going back in

@RealMarcosMiranda 9 ай бұрын

I’m surprised you’d use permanent red loctite instead of purple. Also interesting you add loctite from the opposite end of the hole. I loved the tape idea.

@RaidenF8 8 ай бұрын

That's 222 which is purple actually.

@rajanand153 3 ай бұрын

Broo what if we buy leather rolex then apply silver band to it ( by removing leather band) possible? Please reply

@jamesdanks2415 4 жыл бұрын

Bracelet removal next please Andy 👍🏻

@TheEnglishWatch 4 жыл бұрын

james danks have a look down the list. I think it’s the first post. Was on a Tudor, but it’s the same process.

@soofnic2087 Жыл бұрын

Hi. Thanks for the video. I removed a brick from the same side, but the one before. The one that closer to the clasp. Is it ok? And i dont have locktite. Will the screw can be open by itself over time?

@TheEnglishWatch Жыл бұрын

You should be fine. Glad you found it helpful.

@jrafpor Жыл бұрын

Which width of protective tape did you purchase? There’s variety to choose from.

@TheEnglishWatch Жыл бұрын

I have a complete listing on my website: theenglishwatch.com/hints-and-tips/

@christosvlahos97 11 ай бұрын

Hello! Great video, can you reply in a comment the kind of tape you used? I cant understand with your accent. Thank you so much in advance!

@TheEnglishWatch 11 ай бұрын

Go to my website where you can find all the links on my Amazon store theenglishwatch.com/hints-and-tips/

@orepajic2625 3 жыл бұрын

My wrist is around 7.3 inches... do you think removing only one link is enough or will I need two?

@TheEnglishWatch 3 жыл бұрын

Hard to say. Usually you can wrap the bracelet around the wrist and pinch the loose links together to get an idea. If it’s just loose and you can’t pull 2 links up, maybe 1 will do. Trial and error I think, but put the glide lock on the middle setting so you have some fine adjustment left. Good luck.

@mrtonywolf 3 жыл бұрын

Great video, one of my pins is really difficult to remove, I think it’s got to much lock tight. How do I get round that?

@TheEnglishWatch 3 жыл бұрын

There are a few methods. 1. Heat the threaded end with a hair dryer. It gets hot, so be careful. 2. Submerge the bracelet in very hot water. Don’t let the watch head go in. 3. Flame the threaded end with a yellow flame from a lighter. I don’t like to do this as you can colour the steel if not careful. Best tip is to resign yourself to the fact you may damage the screw head and buy a pack to put new ones in. Usually about £15 for a pack of 5 from an AD. I wouldn’t buy cheap ones off eBay. Good luck.

@algray9966 2 жыл бұрын

WhTs the tape called please

@TheEnglishWatch 2 жыл бұрын

Polyimide tape

@algray9966 2 жыл бұрын

@@TheEnglishWatch many thanks, just looking for a 1.6mm screwdriver now, any recommendations Thanks 😊

@andrewkendall8744 2 жыл бұрын

@@algray9966 Depends where you are, so Amazon, Horotech, Cousins. I have a Bergeon screwdriver. Some say hollow ground tips are the best, but I find they break when the screw is stiff.

@thomasbonass7239 3 жыл бұрын

Hi , would you need to use heat to loosen the glue a bit ?

@TheEnglishWatch 3 жыл бұрын

Sometimes. I’ve had to use a hairdryer before. Avoid direct flame contact. This colours the steel. Sometimes you’ve got to just mash it and buy new screws. Only as a last resort though.

@HisMajesty99 4 ай бұрын

@@TheEnglishWatch what do you mean by mash it? Also if I’ve stripped the screw head, what would I need to do then to remove it?

@TheEnglishWatch 4 ай бұрын

@HisMajesty99 by mash I mean spread the slot in the screw making it ugly or worse case unusable. If you can’t get the screw out, best take it to a watchmaker.

@cmichael2005 6 ай бұрын

How many links in the sub?

@LorenzoStoakes 3 жыл бұрын

great video, unfortunately I got the order of things wrong - I watched your video after I'd scratched my bracelet to fuckery put it back on the wrong way round and removed a link from the wrong side *facepalm* I guess some people are destined to learn things the hard way!!

@Brandon-ju5pg 3 жыл бұрын

Don’t say the f word please.. thank you

@jasonbrody8957 3 жыл бұрын

Fuck fucka fuck!

@gnatboy2762 Жыл бұрын

@@Brandon-ju5pg Fuck Fuck Fuck

@proximity8981 Жыл бұрын

@@Brandon-ju5pg fuck no

@JASONEAVIS Жыл бұрын

@@Brandon-ju5pg Facepalm?

@pdiddy869 3 жыл бұрын

Does the bracket size differ from year to year on the sea dweller

@TheEnglishWatch 3 жыл бұрын

I haven’t tried a Sea Dweller on, but suspect it has similar heft.

@pdiddy869 3 жыл бұрын

By the way, I am referring to the width of the bracelet from the top of the case down. Is it the same for all sea dwellers?

@TheEnglishWatch 3 жыл бұрын

I imagine that all current Sea Dwellers have the same bracelet profile. Not had one in my hand, so can’t honestly say. Look up a WatchBox review. They usually have those details.

@jrafpor Жыл бұрын

Any advice on what to do if I got some tape stuck in the screwhead slot?

@TheEnglishWatch Жыл бұрын

🤔 maybe fish it out with a toothpick.

@GPBS86 Жыл бұрын

Where do you set the glide lock position before removing links? Reason being, don't want to over extend how many links i remove. thanks!

@TheEnglishWatch Жыл бұрын

In the middle so you have a bit of wriggle room.

@GPBS86 Жыл бұрын

@@TheEnglishWatch Thank you!

@myhabibi7782 2 жыл бұрын

Can i know the price of this watch oyster

@juatmac 6 ай бұрын

Wich screwdriver from your Amazon list do you use for Oyster Bracelet? Thanks!

@TheEnglishWatch 6 ай бұрын

The 1.5mm should be fine amzn.to/3GIbLpA

@ryokosimon1080 2 жыл бұрын

I need to make mine super small. I don’t see anymore screws to remove to make it smaller? What do I do?

@TheEnglishWatch 2 жыл бұрын

🤔 I think you may need to visit an authorised dealer. You must have very small wrists.

@EdgeandNikkiNarvaez 3 ай бұрын

What is the size of the screwdriver?

@craigcroly6131 Жыл бұрын

I have a rolex submariner so be nice to know how to take a link out my watch

@badzponad 11 ай бұрын

Hi, do you think I can use Loctite 243 (blue)?

@TheEnglishWatch 11 ай бұрын

Not sure. I think the blue is medium strength as I use it on my mountain bike bolts. It will work, but you may mash the screw if it needs to come out.

@badzponad 11 ай бұрын

@@TheEnglishWatch thanks, thought so

@derekgray1633 Жыл бұрын

ive been too afraid to do this myself for almost 15 years. i got my rolex as a gift from my father a long time ago, its a 50 anniversary submariner kermit green it has the black face and steel band. when you said they are just as likely to scratch it as you are i suddenly took it upon myself to finally make this watch fit! i know i took alot more precautions to prevent scratching than any guy at the jewelry store would have and if i scratched it myself i at least know i was trying to be super careful and can only be mad at myself. it ended up being super easy to do, the screws were a little hard to get loose but this watch hasnt been touched since it was purchased almost 20 years ago. it still has the protective cling on clear plastic on the backside of the watch.

@eugenejohnson7755 Жыл бұрын

Can you use regular scotch tape instead? Thank you.

@TheEnglishWatch Жыл бұрын

I guess you can use any tape. The heat resistance tape is pretty robust though and doesn’t crease easily. It also comes off without leaving a residue.

@eugenejohnson7755 Жыл бұрын

@@TheEnglishWatch Thank you.

@marcgemuelbalagtas7653 2 жыл бұрын

hi @the english watch, mine wouldnt unscrew it;s so tight. i tried everything even direct heat from lighter

@TheEnglishWatch 2 жыл бұрын

Sometimes that is the case. Heat is the best option, not sure I’d go for a flame as this can discolour the link. I have used a hair dryer in the past, but you need to be heating the threaded end. Sometimes you need to sacrifice the screw head and buy some new ones or use one from the spare. Make sure the screwdriver is a good fit. Otherwise its a trip to the AD.

@marcgemuelbalagtas7653 2 жыл бұрын

@@TheEnglishWatch it has a little discoloration and still couldnt get the link out, might go to ad next week. any tips how to remove discoloration from link? does polish works? thanks

@TheEnglishWatch 2 жыл бұрын

A polishing cloth will do it on the polished bits. A scotchbrite pad on the brushed. Long straight movements in one direction over the pad.

@marcgemuelbalagtas7653 2 жыл бұрын

@@TheEnglishWatch thanks, ur the best

@tudorserban111 4 ай бұрын

Is using the loctite absolutely mandatory?

@TheEnglishWatch 4 ай бұрын

No, but means you don’t need to over tighten and damage the screw.

@tudorserban111 4 ай бұрын

@@TheEnglishWatch Makes sense, thanks.

@omarrivera4192 2 жыл бұрын

How can I find that tape? Can someone please tell me how to spell it. Thanks

@TheEnglishWatch 2 жыл бұрын

Just go to the link on my website - theenglishwatch.com/hints-and-tips/

@shqiptar03 Жыл бұрын

Hi! Can u send me link to that screw driver?

@TheEnglishWatch Жыл бұрын

It’s a 1.6mm you’re after amzn.to/3Bs8sQx

3 жыл бұрын

3:09 you're welcome

@bmwf07boy61 3 жыл бұрын

Where can you buy cheap screws for it website name pls

@TheEnglishWatch 3 жыл бұрын

I haven’t used aftermarket screws, but they are available on eBay and through watch supply stores like Cousinsk www.cousinsuk.com/product/bracelet-link-screws-stainless-steel?code=S19193

@bmwf07boy61 3 жыл бұрын

@@TheEnglishWatch Thx

@adamafk590 3 жыл бұрын

Why does the reflection on the date magnification have a blue tint it should be a light brown

@TheEnglishWatch 3 жыл бұрын

I can’t explain. The AR coating in the cyclops magnifier clearly picked up something the room.

@adammccormack7494 2 жыл бұрын

The dealer may well scratch your link .I'm speaking from experience. Thay did So having the tools skills and confidence is key. Lock tight triple 2 brilliant Thank-you for a great confidence booster knowledge is key .Adam