This man just rebuilt a top end in under 50 minutes darn tootin
@probablyonahonda4 жыл бұрын
I have done one in 23min (wasn't my best work)
@pacemohr86164 жыл бұрын
ever time i do it it takes 45 min and i’m (15)
@utahwanderlust7003 жыл бұрын
Yeah, but he left out the stuff that takes the most time; Plastics and gas tank. He also didn't check ring gaps or measure piston/ cylinder wall clearances.
@louisroy55533 жыл бұрын
And he is wearing flip flops...
@newbsauce872 жыл бұрын
@@probablyonahonda im 12 and done one in 12 mins loser
@tylerjames91014 жыл бұрын
I’m not even rebuilding my top end I just enjoy your videos
@skylertidmore51264 жыл бұрын
I don't even have an ATV and I just watched this whole video! I love learning and this guy is freakin awesome. Definitely makes me not nervous to do this job myself now.
@ReapNationGaming20232 жыл бұрын
Well explained! About to be doing this myself to my 2017 with 150 miles on it after I sunk it and turned it into a fog machine then let it sit because I have a "CAN'T AM" but ready to get it back up.
@rickyborden32874 жыл бұрын
A woman who can sit and watch you rebuild a motor is a good woman. A woman who can sit quietly and watch you rebuild a motor is a great woman. Never let her go.
@Day12My Жыл бұрын
She could have grabbed the damn camera and helped him out. The part he was obviously struggling to video and work
@Pur3R3dBlow7 ай бұрын
Or a woman that’ll actually help rebuild said motor now that’s a keeper
@charlesgumulinski39979 ай бұрын
Your really good at this. Great demonstration
@wonderbread27644 жыл бұрын
I dont even own a Honda but I just watched the entire video lmao
@waynesivuarapik25722 жыл бұрын
I learned from mud puppy on the top end rebuild now I do my own atv even the valve adjustments thanks to mud puppy
@buildurtruckurway91182 жыл бұрын
We did this on the trail 2 years ago. Buddy cracked a piston in his rubi and we couldn't pull him 20k thru the mud and up shale covered hills. We ran to Honda picked up a gasket set and ordered a niche 10-1 piston off amazon. Took us about 3 hrs to get done with limited supplies it ran better than new afterwards. Bike sat in the woods for 3 days before we had the parts together.
@brandonbetts3512 жыл бұрын
Great video man!
@nighthawkj30A44 жыл бұрын
You could use Silicone spray on the rubber exhaust mounts when removeing and and installing.
@panicx57394 жыл бұрын
Came out at the perfect time, doing first rebuild of mine Monday. Worried about the ring gap and haven’t been able to find the diagram online
@MudPuppyOffroad4 жыл бұрын
Download a $5 manual It will save you a headache
@mmasinator4 жыл бұрын
Someone been watching zip ties n bias plies lol
@MudPuppyOffroad4 жыл бұрын
Way too much lol
@ryker17254 жыл бұрын
Haha that dudes funny as hell
@mississippimudslutscrew97424 жыл бұрын
Mud Puppy can you please tell me if this is the same process on a 2018?
@MudPuppyOffroad4 жыл бұрын
@@mississippimudslutscrew9742 yup
@Day12My Жыл бұрын
28:21...Fill cap up with vasoline and screw on. Any kind of sealant will be good as new when you want to use again.
@onewayklay61752 жыл бұрын
Finna build mine gonna watch whole video again while doing it 🤣
@thefloridaman23484 жыл бұрын
HELL YEA A 50 MINUTE VIDEO HELL YEA MUD PUPPY THANK YOU
@jaxsen.10584 жыл бұрын
i learn so much from this channel
@NelsonCreekCustoms4 жыл бұрын
14:35 your heart had to skip a beat mine did 😂
@Ceemysix4 жыл бұрын
EaZier Clutch Yep. Mine did.
@christianjahn41412 жыл бұрын
I torqued everything down right , why is coolant leaking out my head gasket and ig getting in the cylinder and making it smoke any idea ? Yes the coolant is getting in the oil
@Etxmudriders552 жыл бұрын
I just did mine and I’m getting no compression I didn’t I just my valves could that be the problem????
@andrew-od7yt Жыл бұрын
whenever i pull my jug and valvues i get ALOT of coolant coming out. how do i prevent that?
@philipfaulk2910 Жыл бұрын
Got a question, first off love your videos…in this video every thing was described perfectly. However after rebuild new oil and coolant…after 30 min of. Riding the atv started over heating…seems my reservoir is filling up but not returning to radiator. Water pump? Clogged return?? Not sure.
@MudPuppyOffroad Жыл бұрын
It could just be air trapped in the system. these ATVs usually bleed themselves but you can check by removing the hose on the top of the thermostat housing and see if you get any air pushed out
@MudPuppyOffroad Жыл бұрын
If your Reservoir is filling up and not returning that usually means you need a new radiator cap but that's pretty rare on these
@MudPuppyOffroad Жыл бұрын
Obviously make sure your radiator is very clean
@christophertalbot1128 Жыл бұрын
Question, when I put the valve cover on, it didn’t sit on there “nicely” I’m thinking one of the four studs backed it’s way out a little and is hitting the rocker.
@MudPuppyOffroad Жыл бұрын
I suspect Your engine isnt at tdc. So youre trying to open a valve by putting the cover on.
@Waynerebelrider4 жыл бұрын
I bet those water cycles require top in regularly👍📽
@NelsonCreekCustoms4 жыл бұрын
Wayne c Menard rebel rider yea when you swamp it back to back to back
@andysnail47744 жыл бұрын
I had to cut my 350d piston in half to get it off the ristpin sezed up on her
@zaceribarkhouse35924 жыл бұрын
I have a question about my honda 500 218. It keeps getting water in the air box and and I don't know if there is any popular issue with them doing it.
@ReapNationGaming20232 жыл бұрын
@Zaceri Barkhouse Put the 420 IRS rancher airbox in it with OMG airbox gasket
@MrTNBassmaster4 жыл бұрын
New sub awesome video,. What was the problem ? To warrant a new top end ? Thanks
@MudPuppyOffroad4 жыл бұрын
Got sunk a few times rings were shot cylinder was scraped up
@MrTNBassmaster4 жыл бұрын
@@MudPuppyOffroad thanks , I was on my 06 Foreman 500 going up a small hill on the Hatfield and McCoy trail here WV on Wednesday at the end if our ride it started losing power and it was making a noise in the top end then it finally died . I think it dropped a valve haven't had time to check yet .
@UnoShots Жыл бұрын
So did you ever find out if the oem 520 cylinder fits the 2017? Ive got the 500fm1 foot shift straight axle And would like to do the top end also does the new head differ from the 2017?
@MudPuppyOffroad Жыл бұрын
Great question for the patreon page!
@TEXAZPITBULL3 жыл бұрын
How much you charge for a job like this 2005 Honda Forman 500
@norbertohernandez45693 жыл бұрын
Hey sr I have a question I have a 2017 Honda 500 do you think the piston set for a 420 will work on my Honda?
@MudPuppyOffroad3 жыл бұрын
I have no idea nor do I know why you would want to go to a smaller piston
@hunterwyrick74643 жыл бұрын
Where can I find that service guide you are using for the ring set? Trying to rebuild I 17 rubicon
@MudPuppyOffroad3 жыл бұрын
Just Google 2017 Rubicon manual there's a bunch of PDFs out there you can buy for a few bucks
@nighthawkj30A44 жыл бұрын
Also is that a page from the Factory service manual?
@MudPuppyOffroad4 жыл бұрын
Yep
@utahwanderlust7003 жыл бұрын
I would never go to all the work of rebuilding a top end without checking ring gaps and piston/cylinder wall clearance. 10 minutes checking that shit could save you hours of doing it all over again. Also, rags are good to use, not just talk about. You just about had one of those dowel pins drop in the bottom. You were damn lucky.
@MudPuppyOffroad3 жыл бұрын
Thanks for all your opinions lol when you install a new OEM jug with OEM rings and an OEM piston eyeballing the rings is good enough I've done dozens way more than you I'm sure
@MudPuppyOffroad3 жыл бұрын
Also if you watch the video closely you can see that I can rebuild a Honda top end in under an hour lol
@utahwanderlust7003 жыл бұрын
@@MudPuppyOffroad Typical answer from Christian the arrogant prick. You really are full of yourself aren't you? Honda can have a fuck up just as easy as anybody else. Also, they don't make their rings. Somebody else does. They can be out of spec. So why not check them? Takes 10 minutes.
@utahwanderlust7003 жыл бұрын
@@MudPuppyOffroad Yeah, if you don't count taking all the plastic off and the gas tank and the exhaust. Since you can't do a top end without removing that shit, it gets added into the total time.
@MudPuppyOffroad3 жыл бұрын
I do check rings whenever building something with tight tolerances that it matters like my 450 for instance. Even then it doesn't take me 10 minutes more like 30 seconds... but then again I'm a genius so I understand why it takes you so long
@jackcowan3513 жыл бұрын
Is this the same general idea on an 02-04 500 Fa-a
@MudPuppyOffroad3 жыл бұрын
No
@NoSend9014 жыл бұрын
Just bought a 2020 foot shift rubicon , do you think I’ll have a problem turning 28x9.5x14 outlaw 2’s?
@MudPuppyOffroad4 жыл бұрын
Yes those are an extremely brutal tire They are hard and might as well be square They will break all kinds of stuff and are hard to turn They do pull amazing in clay though
@NoSend9014 жыл бұрын
So the OG outlaw will be better?
@chase_22494 жыл бұрын
This may sound like a stupid question but how do you know if you're getting low compression and is it a very noticeable loss in power and other than loss of power are there any other signs??
@daltonfrith76854 жыл бұрын
Smoke is a good sign of it and the sound of the engine will change when its spinning over also.
@chase_22494 жыл бұрын
@@daltonfrith7685 Thanks, is it like a ticking when its spinning over?
@hardr71944 жыл бұрын
chase_224 it’s a slow start almost sounds like your starter is going bad
@yohanathandowns90574 жыл бұрын
You'll just notice an over all loss of pep and perkiness
@High_Octane4 жыл бұрын
how often do people say you sound like Kyle from 1320Video.? lol
@GNR3253 жыл бұрын
So I take it you prefer Honda ATV's for mudding? What is your opinion on the Yamaha's?
@MudPuppyOffroad3 жыл бұрын
Have belts greared high, loved my bbig bear though
@GNR3253 жыл бұрын
@@MudPuppyOffroad Yamaha seems to have one of the best belt set-ups. I agree though that they seem geared a little high for big tires. I see a Brute Force in some of your videos. How are they sealed up for the deep stuff?
@chrishansen80264 жыл бұрын
Where is the timing chain? Did I miss it being removed? I’ve never seen top ends rebuilt on utility quads so please forgive my negligence
@MudPuppyOffroad4 жыл бұрын
It does push rods... It's not overhead cam
@chrishansen80264 жыл бұрын
Mud Puppy oh okay thanks
@Frog_man007 Жыл бұрын
How would you compare rebuilding a Honda over a Can-Am or Polaris?
@MudPuppyOffroad Жыл бұрын
I mean it depends on the Honda these are extremely simple because they're pushrod unlike anything else in the market right now
@Frog_man007 Жыл бұрын
@@MudPuppyOffroad what’s your reason for not really ever getting into the Polaris world? I know you have owned a few I believe but you usually stick with Honda’s.
@backyardbashing61363 жыл бұрын
Maybe you have a video on it but what’s the best programmer to make sure everything runs right? I will be doing this on my 420
@mistersniffer68382 жыл бұрын
Not worried about a hydro locked/bent rod?
@MudPuppyOffroad2 жыл бұрын
Extremely rare on a single cylinder engine
@j.bassing94904 жыл бұрын
I know mud puppy this is a dumb question but how do u keep water out of the oil and I’ve binged watch all your vids hoping to get a four wheeler soon
@marshallives6584 жыл бұрын
Well the main thing that will get water in the oil is the crankcase vent, so make sure it’s ran into your airbox, also look up crankcase breather mod, it’s by project ajax on KZfaq
@kurtwandro75173 жыл бұрын
Is a top end rebuild on a 2006 rubicon pretty much the same? I can't find anything on 05-14.
@MudPuppyOffroad3 жыл бұрын
Nope very different
@ervingunderson66823 жыл бұрын
The 5 people who disliked it didn’t wanna do shit so they send the damn motor out just to do a simple 1 and half hour work😂.
@Vroomtastic3 жыл бұрын
How to I know I’m at top dead center
@SRay-xy1pc4 жыл бұрын
How many topends before the bottomend needs replacing
@MudPuppyOffroad4 жыл бұрын
Depends how much water's been in the oil
@Bt2tymz3 ай бұрын
My rings are catching onto the cylinder and it’s not allowing me to push the piston I to the cylinder
@MudPuppyOffroad3 ай бұрын
Might need to file the rings
@THETYLERCLARK0010 ай бұрын
My oil ring won’t sit all the way in. Is that normal?
@MudPuppyOffroad10 ай бұрын
Obviously it's hard to say without seeing a picture but it sounds like it might be normal
@charlesgumulinski39979 ай бұрын
How do you know all this shit. U have skills
@cagelewis27923 жыл бұрын
Is there any way you still have the part numbers
@ReapNationGaming20232 жыл бұрын
partzilla is your friend
@Josejones_3321 Жыл бұрын
So great to have a manual but what about the people who don’t
@MudPuppyOffroad Жыл бұрын
There is no excuse for not having a manual you can download you can download one for $5
@paytonschefer81394 жыл бұрын
Do you know if you can install a 520 jug and piston on one of these 500s?
@MudPuppyOffroad4 жыл бұрын
Not without grinding the case
@patrickmontgomery10454 жыл бұрын
Mud Puppy do you know if it is worth grinding the case?
@michaelwaterford2290 Жыл бұрын
How many hours did it take
@MudPuppyOffroad Жыл бұрын
3
@hondaboatin371 Жыл бұрын
Came out with an impact it’ll go in with an impact 😂😂 should put that shit on a shirt
@chasedrapal68822 жыл бұрын
Thinking about the same for a pioneer 500 ?
@MudPuppyOffroad2 жыл бұрын
Yep!
@chasedrapal68822 жыл бұрын
Hell yeah love your videos man gonna rebuild mine next weekend.
@flfishing62622 жыл бұрын
Where can I get a 35% gear reduction for a rancher 420
@MudPuppyOffroad2 жыл бұрын
A lot of people sell the 35 and a 40% reduction boss has the easiest website
@gonzaloloz4 жыл бұрын
I have the same working table Lol
@adampresley063 жыл бұрын
Would you be interested in helping me or showing me how to rebuild my 2014 Rancher need a full motor rebuild I’m buying the parts I’m 14 and looking to learn??
@MudPuppyOffroad3 жыл бұрын
This video is all you need... Exact same process
@adampresley063 жыл бұрын
@@MudPuppyOffroad I am putting a new bottom end in as well
@Bt2tymz3 ай бұрын
I threw the ring into the cylinder to check the gap and it’s damn near touching
@MudPuppyOffroad3 ай бұрын
That's not great, some people file them
@Bt2tymz3 ай бұрын
@@MudPuppyOffroad yea I had to order the tool to do it
@MudPuppyOffroad3 ай бұрын
@@Bt2tymz I've had a few Honda cylinders come in off lately, aftermarket has been better LOL
@Bt2tymz3 ай бұрын
@@MudPuppyOffroad crazy too me cause I spent $620 for my oem kit thinking everything would be perfect
@juanvilla62052 жыл бұрын
By chance can you post all the part numbers?
@swiftproductions57194 жыл бұрын
When I put my top end on, I messed up by putting the piston on the crank before the jug... and that was the biggest pain in the ass I’ve ever experienced
@djwilliard38914 жыл бұрын
SwiFtProductions man I had the same problem lol
@TheHomePros62213 жыл бұрын
It will start smoking if u don’t clean the crank cases which I’m sure u did
@sweatlodgegarage81954 жыл бұрын
the best rebuild video ever. “literally the slowest atv in existence, it’s not a top fuel dragster.” LOL
@Bt2tymz3 ай бұрын
16:08 where can I find that paper ?
@MudPuppyOffroad3 ай бұрын
Oem manual for ring stagger
@MudPuppyOffroad3 ай бұрын
Service manual not owners manual
@nighthawkj30A44 жыл бұрын
I don’t stand as Advanced Honda/Acura engines are with there VTEC and J series V6 SOHC engines. Why still use OHV push rod engines. On there Powersports. Use SOHC engines like how Yamaha does.
@ok94252 жыл бұрын
I took all the body part off before watching this video 😐
@Xxsheeshvibes7 ай бұрын
You got to pay to play
@isaacposs01274 жыл бұрын
First
@isaacposs01274 жыл бұрын
Love u mudpuppy
@jayblue82244 жыл бұрын
Couldn't see half of what u were doin... Just like you're valve adjustment video..... Angle your camera down a hair..!!??????!???
@joshstaley7459 Жыл бұрын
what happens if a guy got that piston in backwards.. ?? intake is not to the intake side