Super73 DIY Ebike Lighting Kit | RunPlayBack
Рет қаралды 44,462
3 жыл бұрынIn this video we show you how to build your own DIY lighting kit for the Super73 Z1 or just about any ebike. We discuss the parts we used, the tools you need and we even share our wiring cheat sheet to make it easier for you. #super73 #super73z1 #ebike
Want a discount on your Super73? Use my promo code here: www.talkable.com/x/fqj0WT
RunPlayBack Merch: shop.runplayback.com/
Our Lighting Kit Setup:
5.75" Wisamic Headlight: amzn.to/3wDVDyi
Headlight Grill: amzn.to/3yLqxqB
H4 Headlight Harness: amzn.to/3vATXFT
5.75" Headlight Housing: amzn.to/3fwL5LM
8" LED Taillight: amzn.to/3fCDUBU
LED Turn Signals: amzn.to/3zmfjZJ
Front Handlebar LED: amzn.to/3znFZte
Rear Frame LED: amzn.to/3ivXJwu
Light Switch: amzn.to/2SsC3Xq
12v Horn: amzn.to/3getE2Y
Flasher Relay: amzn.to/3gIIM7V
12v Step Down Converter: amzn.to/3xfFI9F
Microswitches: amzn.to/35clIJ9
12v Battery: amzn.to/3zhORAF
Cloth Tape: amzn.to/3gibvBj
Ring Connectors: amzn.to/3zn4gzt
Distro Box: amzn.to/3iyktMp
Crimping Toolkit: amzn.to/3fxEwIT
SUPER73 Z1 WIRING LENGTHS
18" Tail Light
29" Headlight
33" Front Indicators
33" Front Handlebar Lights
20" Rear Indicators
18" Rear Frame Lights
36" Light Switch
19" Light Switch to Horn
33" Horn to Positive
GROUP A: HIGH BEAM LIGHTS
Headlight - high beam wire
Front Indicators (Left and Right) - white light wires
Front Fork Lights (Left and Right) - white light wires
GROUP B: LOW BEAM LIGHTS
Headlight - positive wire
Tail Light - low beam wire
GROUP C: LEFT LIGHTS INDICATORS
Tail Light - left indicator wire
Front Indicator Left - indicator wire
Front Fork Light Left - indicator wire
Rear Indicator Left - indicator wire
Rear Frame Light Left - indicator wire
GROUP D: LEFT LIGHTS NEGATIVE
Front Indicator Left - negative wire
Front Fork Light Left - negative wire
Rear Indicator Left - negative wire
Rear Frame Light Left - negative wire
Tail Light - negative wire
GROUP E: RIGHT LIGHTS INDICATORS
Tail Light - right indicator wire
Front Indicator Right - indicator wire
Front Fork Light Right - indicator wire
Rear Indicator Right - indicator wire
Rear Frame Light Right - indicator wire
GROUP F: RIGHT LIGHTS NEGATIVE
Front Indicator Right - negative wire
Front Fork Light Right - negative wire
Rear Indicator Right - negative wire
Rear Frame Light Right - negative wire
Headlight - negative wire
GROUP G: BRAKE LIGHTS
Tail Light - high beam wire
Rear Indicator Lights (Left and Right) - red light wires
Rear Frame Lights (Left and Right) - red light wires
GROUP A : Light Switch - high beam wire
GROUP B : Distro Box - positive terminal
GROUP C : Light Switch - left indicators wire
GROUP E : Light Switch - right indicators wire
GROUP G : Brake Switch - Microswitch common wire
Microswitch Normal Open Terminal : Distro Box - positive terminal
Light Switch Headlight Positive Wire : Distro Box - positive terminal
Light Switch Horn Wire Negative : Horn
Light Switch Indicators Positive Wire : Flasher Relay L Terminal
ALL of My Camera Gear and Movies:
www.amazon.com/shop/runplayback
My Links:
Instagram - / runplayback
Facebook - / runplayback
Twitter - / runplayback
Email Me - runplayback.com
@RunPlayBack 3 жыл бұрын
Want a discount on your Super73? Use my promo code here: www.talkable.com/x/fqj0WT
@jamesbird9588 8 ай бұрын
FINALLY!! i have been searching for a helpful bike lighting video for a couple weeks now, yours is by far the best and most helpful for someone with near zero electrical knowledge. Thank you!
@jamesbird9588 8 ай бұрын
you could repost this with a different voiceover and title as i believe it would be helpful for ANY E-Bike/Scooter builder
@RunPlayBack 7 ай бұрын
Glad it helped!
@clemonsjoey 2 жыл бұрын
Well done! Love watching others customize their bikes too👏👏👏
@RunPlayBack 2 жыл бұрын
Thank you! Same here! Looks like you've done some interesting mods as well. Keep it up! 👍
@clemonsjoey 2 жыл бұрын
@@RunPlayBack I just took my bike completely apart in my livingroom to mod for the winter. New QS205 V3ti 650 turn 5t motor, it’s at a motorcycle shop as we speak getting laced with powder coated stainless steel 8ga spokes on my 26in anodized rim. New Shimano Ice Tech floating rotor, rotar bolts, tire, rim liner, Kevlar tire liner, new Honda seat, turn signals, new Tron wheel lights, new motorcycle headlight/horn/turn signal switch, etc. It’s going to be a whole new bike. 💸💸💸
@RunPlayBack 2 жыл бұрын
@@clemonsjoey That sounds amazing! Can't wait to check it out!
@Webbsy Жыл бұрын
I'm starting a retro moped restoration and converting it into an ebike. This video has been immensely helpful, thank you! !
@RunPlayBack Жыл бұрын
Nice, that's a fun project!
@paradisekii7706 3 жыл бұрын
Thank u! Amazing work, appreciate the time you put into this.
@RunPlayBack 3 жыл бұрын
Glad you enjoyed it! I hope it helps others build their own lighting systems!
@cycleguy417 2 жыл бұрын
Love it!!! ❤️❤️❤️ Finally found the guide I was looking for
@RunPlayBack 2 жыл бұрын
Enjoy!
@landslave Жыл бұрын
Literally the only ebike guide on KZfaq that I can find. Great job. Thanks! The brake light control switches are the most challenging part.
@blockycraftpartyplayz7015 3 жыл бұрын
That Ebike ride was fun!!
@RunPlayBack 3 жыл бұрын
Hey Miles! Yes it was fun, let's do it again! 😃
@fassphoto 2 жыл бұрын
Awesome work! I am planning to do something likely on my Rad mini 4 maybe a little simpler. Your videos are very inspiring. 😎👍
@RunPlayBack 2 жыл бұрын
Awesome! Thank you!
@ikehigh05 2 жыл бұрын
Great video. i did something similar and you literally did everything I did, in the same order lol. The only thing I did differently was used a Octocouple relay to interface the ebrake signal with the 12v source and the 12v rear brake light.
@RunPlayBack 2 жыл бұрын
Nice work! Thank you for sharing! 👍
@eugene188 2 жыл бұрын
I can see how this could be really fun to do for some ppl, but really these bikes should come with lights standard.
@RunPlayBack 2 жыл бұрын
I agree!
@Pyrotek28 Ай бұрын
Get a set of breaks handles with the built in switch and tied it in to high break and powered the break light through the high imput and used the low input for tail light. it would save a bit of wiring.
@tailslapexplore6887 9 ай бұрын
Look sick bruh 👍👍too bad i'm kinda fool on cable or wire. Appreciated it ✌
@RunPlayBack 9 ай бұрын
Glad to help!
@aeskellion 3 жыл бұрын
love it. I kinda want to customize it a bit though, I think I’ll ditch the DRLs and use a separate 12V battery for everything.
@orange73 3 жыл бұрын
Yeah, I plan to use a separate 12v battery for my lighting install. I don't wanna give the game away just yet, but I have found quite a novel solution.
@RunPlayBack 3 жыл бұрын
Sounds good! Yeah, there's so many ways to customize to your liking. Just wanted to show the basics of how to group everything. This is the portable 12v battery I used in the video amzn.to/3gwPcGK
@RunPlayBack 3 жыл бұрын
Nice! I was using the TalentCell battery for testing: amzn.to/3gwPcGK
@aeskellion 3 жыл бұрын
@@RunPlayBack and I’m very grateful for this. I wanted to have a full lighting kit for the bike but I didn’t want to mess it up
@riddickstark9628 2 жыл бұрын
Just got my Super 73rx and really want to add lighting, live in NY and traffic here is a bit hectic, definitely need to be visible at night. This was really helpful but intimidating as I know nothing about electrical wiring lol. Wish there was ebike stores here that offer this service.
@RunPlayBack 2 жыл бұрын
Try hitting up instagram.com/datshopnyc They specialize in this kind of custom lighting for high performance ebikes.
@whatis4566 3 жыл бұрын
Looks good
@RunPlayBack 3 жыл бұрын
Thanks Moses!
@jcreary100 2 жыл бұрын
Nice setup
@RunPlayBack 2 жыл бұрын
Glad you think so!
@beestrongbc Жыл бұрын
Hey 😃 I Just Happened to Find Your Video On Wiring And Found It to be Very Helpful. Being that I'm Getting Ready to Start My Own Project, I Can Use All The Help I Can get. 🙂👍🏾 You did a Great Job On The Wiring Process, One Of The Best I've Seen. But Instead of a Bike I'll Be Wiring My Electric Scooter. Some Of the Things You Explained, I See I Was Right On Point With You On, So It's Good to Know that I Was Moving In the Right Direction. So Thank You and You Just Pick Up a New Subscriber. 🙂👍🏾🔥🔥🔥🔥🔥✌🏾🛴🛴🛴🙏🏾🙏🏾🙏🏾
@RunPlayBack Жыл бұрын
That's awesome! Happy to help! 🙏🙏🙏
@f0ca94 2 жыл бұрын
Very impressive. Good work! :)
@RunPlayBack 2 жыл бұрын
Thanks! I hope it was helpful!
@f0ca94 2 жыл бұрын
@@RunPlayBack definitely! I think I will have to learn a bit more before getting to this project through because I've never done electric work and that's a lot of cables 😁 buts definitely I would like to get to the point where I feel comfortable following through this project.
@RunPlayBack 2 жыл бұрын
@@f0ca94 Yeah it can seem like a lot but my best advice is to take it slow. It's not really a one day project. It's best to take a few days to wrap your head around all the wiring and to test all your connections. And when you do it once you can pretty much apply it to any other bike.
@PlanetOwner 3 жыл бұрын
If you are going to do something you might as well do it right and you are always doing it right!
@RunPlayBack 3 жыл бұрын
Haha thanks bro. Not sure if its right or even the best way to rig this. But it works! 😂
@PlanetOwner 3 жыл бұрын
@@RunPlayBack absolutely works and much better than I would have done🤣
@GapRecordingsNamibia 8 ай бұрын
A bit late to the party, but, just an FYI if you do this again. If your break switches go to ground when breaking you can use a mosfet being triggered to switch your break light rather than using exposed switches. Will also cut down on the amount of wires. Nice tutorial.
@RunPlayBack 8 ай бұрын
Great tips thank you for sharing!
@tailslapexplore6887 9 ай бұрын
😁😁 like a human torso head, both hand, both leg and tail ( break light ) 👍👍👍
@Sarge92 2 жыл бұрын
for the brakes look for Ebike Brake Cutoffs they make them for hydraulic and cable brake systems but they have the switches already integrated and ready to go there normally used for ebikes to shut off the motor when braking but should work fine for what you need
@RunPlayBack 2 жыл бұрын
Yes definitely! We actually upgraded to Magura MT7e's with the built in switch.
@stan121midling5 Жыл бұрын
@@RunPlayBack do you have the link for this please ?
@pajamawrestler 3 жыл бұрын
It's lit!
@RunPlayBack 3 жыл бұрын
haha yeah it is! super lit!
@frankjames5396 2 ай бұрын
Im trying this on my lectric xp 3.0. I wanna be visible at night and refuse to use removable lights. Youre right though ,this is an intense project for a novice.
@grantsvlogs Ай бұрын
You could 3d print a housing for the microswitch
@dimayaomel 2 жыл бұрын
Wow, i do almost the same. But relay for turn lights is shit, i want find another. Very good video.
@RunPlayBack 2 жыл бұрын
Nice thank you! Let me know if you find a better relay!
@sumnsumn1490 7 ай бұрын
I would really love your input - I'm stuck as I'm trying to use my stock brakes. I thought it would be fairly easy to tie into the wires already connected there but I'm seeing it's not that simple Did you in your Z1 adventures ever come up with a pin out slash color code for the front wiring harness? Ideally I'd like to use the OG throttle as well if I can just to save a few dollars right now. If you could please get back with me when you have a chance I appreciate you and your content 🙌
@snowsims146 2 жыл бұрын
Hey, great video! Do you know if you are able to use the existing controller/12v step down on the RX for this kind of set up. Looking to add 4 turn signals to the existing headlight and brake light system.
@RunPlayBack 2 жыл бұрын
Thanks! Unfortunately I don't own an RX so I'm not sure if the 12v step down could work. But if you can tap into it I don't see why not!
@Kevin6t8 6 ай бұрын
My Aniioki AQ177 Pro Max already has a brake light with the turn signals built in, but no front turn signals. I was wondering if I could splice into the existing wiring to add front signals.
@simonm7658 2 жыл бұрын
Hey thanks 4 this video, how can I connect the controller battery with the 12v converter
@RunPlayBack 2 жыл бұрын
We used an XT-60 splitter amzn.to/3tXRllo
@andrewdaniels1654 2 жыл бұрын
So if my bike has a break light that turns on when I break could I just parallel off that connection instead of the micro switches?
@RunPlayBack 2 жыл бұрын
Yes that's correct! I've done that with my Magura MT7e's which have brake sensor wires.
@myfreefiretvgoogleplus5823 11 ай бұрын
Where did you connect flasher to? If my front blinkers have an internal flasher resister to make them blink, would I still be able to add a flasher to make my rear blinkers work? It’s a strip blinker with brake light and lights up red all the time, o believe the same as the one you are using
@tour2778 Ай бұрын
i got a ouxi v8 1.0 and im wanting to do turn signals in the front light, in its ring, but i dont know if its possible..
@landslave Жыл бұрын
The wire size guide says that I can run my entire system on the 18AWG wiring through the multiswitch I have with no relays except the flasher. Calculated current draw is 72W @ 12VDC (6A momentary when horn is on) an 45W @ 12VDC (3.75A) nominal with every draw except high beam and horn on (I plan on not using high beam). Rated stranded copper is up to 9A. I will be fused at either 10A or 7.5A. Does that all sound correct? Thanks!
@RunPlayBack Жыл бұрын
That should be fine. The current draw from the horn is only momentary, so there is very little concern with regards to the "proper" wire gauge for it.
@CirclesLikeAnFigure8 3 жыл бұрын
👍🏾
@williegramirez1355 6 ай бұрын
YO YO, my brotha. Great video. Can I ask you what the name of the plug that goes into 12 volt battery ? I want to connect one or two whip lights that usually go on ATVS. To a RadPower Radrunner 1 electric bike. It should be easy wiring connection red positive, black negative and what do the yellow and other black wire go to? If you all have time I would appreciate your advice. And if you have link to buy plug that goes into 12 volt battery.
@josephchan7040 2 жыл бұрын
Awesome video. One clarification question on the 12v converter. Is the converter directly attached to the s73 battery, as in you split it?
@RunPlayBack 2 жыл бұрын
you that's correct
@josephchan7040 2 жыл бұрын
@@RunPlayBack hate to ask dumb questions, but can you tell me where you you spliced it? Before or after the controller? Also did you fuse it? Photo helps too if possible but understand it's inconvenient. Thanks.
@RunPlayBack 2 жыл бұрын
@@josephchan7040 sorry don't have access to the build at the moment but basically I made an XT60 splitter off the battery. XT60 to battery and positive and negative wires spliced into 12v step down. I didn't fuse it but you can if you want.
@paularmstrong7428 Жыл бұрын
I've pretty much ordered everything you listed on hopes for a same/similar setup. I have the same light switch, relay, & led strips. With the DRL lights of the strip on, the flasher relay does nothing but constantly light. If the DRL isn't on, the flasher works as expected. Not sure what I'm doing different. Do you flashers/turn signals work if the DRL lights of the strips are on?
@RunPlayBack Жыл бұрын
It should work if wired correctly (DRL and blinkers). If DRL is on, and say left blinker is enabled, then the left blinkers should flash amber, when the blinker is disabled, then it should return to DRL mode. You should double check that all connections are solid, and make sure you don't have any shorts (bare wires that are not supposed to be touching), and also make sure that ground/return connections are isolated. GL!
@RyanPhung725 Жыл бұрын
Hi! for the turn signal switch, does the turn signal cancel when you press the button or do you have to move it back to the center position to turn off.
@RunPlayBack Жыл бұрын
You have to move it back to center
@thomaschung9310 2 жыл бұрын
Are the turn signals designed to flash several times every time you hit the brakes or is that what happens when you add the flasher relay? I like how it really let's the ppl behind you know you're braking.
@RunPlayBack 2 жыл бұрын
Only the signals are attached to the flasher relay. I think you could also do a flasher relay on the brake light but it might really be street legal. You can also control the speed of the flash with the relay.
@NicolaMs007 Жыл бұрын
am wondering am going to be buying a Ace X Demon here in Australia, (similar to the Aerial Rider Grizzly) if the same setup here could be done on that bike as well? If so I would be wondering if it would need to be registered for the road, or is it still an e-bike electric bicycle
@RunPlayBack Жыл бұрын
Hi, thanks for watching! You would have to check your local region laws regarding legality. The AR Grizzly has dual 1000w motors, it can be ridden in class 2/3 modes, but I'm not familiar with how Australia governs ebikes. To answer your other question, yes you can run the same setup for the lights, the concept is the same.
@cloudroot315 2 жыл бұрын
Great vids……can’t find link to cheat sheet. Would be super useful thanks
@RunPlayBack 2 жыл бұрын
Thanks! The cheat sheet is written in the description.
@lincoln169 2 жыл бұрын
What are good rechargeable rear lights with turn signals for both, day and night use?
@RunPlayBack 2 жыл бұрын
These seem to be popular for those who don't want to deal with all the wiring - amzn.to/3Djw7SB
@lincoln169 2 жыл бұрын
@@RunPlayBack Thanks. They look a lot better than the other ones I was looking at. It would be nice to find something like motorcycle rear lights. I want people to be able to see the signals during the day too.
@komodospider Жыл бұрын
Hi! At 11:12 of the video, how did you create the splitter? Thank you!
@RunPlayBack Жыл бұрын
It's just a few wires - strip the ends, twist the ends together, solder together and then attach to a crimp connector
@komodospider Жыл бұрын
@@RunPlayBack Ok! Which ones are +ve and -ve? And should there not be 6 (3 pairs) instead of 5? Thank you!
@jonasmeier417 2 жыл бұрын
Can I wake you up at 3 AM and you know which switch is which?:-)
@RunPlayBack 2 жыл бұрын
I'm awake lol :) Can you elaborate? The signal switch?
@leoelegado 2 жыл бұрын
Great job! For the 12v step down converter, how many amps/watts did you select?
@RunPlayBack Жыл бұрын
For LED lighting, the only "high" current draw is the headlight, we wouldn't go higher than 10A output from the DC-DC stepdown
@freakenstein1984 2 жыл бұрын
Hey do you think you could build me a kit for the razor rsf650. But its upgraded to 72v 5000w motor. Id add 12v battery to run the lights. I really need your help since I have no idea about wiring . I'll buy it if you can do it
@RunPlayBack 2 жыл бұрын
Hey! Actually there is someone who specializes in custom lighting kits. Trying contacting Alvin Bows at DatShopNYC. He works on all kinds of ebikes from Onyx, Surron, Super73 etc. I think he may be the best person for this kind of work as I'm not a vendor. instagram.com/datshopnyc
@freakenstein1984 2 жыл бұрын
@@RunPlayBack thanks my man 👍👍👍👍
@pickleemm4735 Жыл бұрын
Is it possible to do this setup without using a DC-DC converter? Or slightly similar by wiring the lights and switches in series?
@RunPlayBack Жыл бұрын
Hi, not exactly sure what you mean. If you use 48v switches and lights, then there is no need for a DC-DC stepdown. 12v lights and switches are super common and have a wide variety of choices, that is why most folks would prefer to install a DC-DC stepdown, or run a separate external 12v battery.
@pickleemm4735 Жыл бұрын
@@RunPlayBack I would like to try do it without adding the extra dc-dc converter as it's another piece to secure to the bike. I've seen that you for a 48v battery you could run 4 X 12v lights in a series circuit so that it adds up to 48v without the need for the step down converter. Have you done anything similar? I liked the setup you did on the Sur-On Bike
@BushidoGoon 2 жыл бұрын
Do you need 2 flasher relays? 1 for each side?
@RunPlayBack 2 жыл бұрын
You just need one..it connects to the signal switch which activates the flash across all lights connected to left and right signal wires.
@JawadAhmadsahibzada 2 жыл бұрын
i watched whole video, i wished you shared a wiring diagram so that i can make mine, i'm confused and don't know from where to start
@RunPlayBack 2 жыл бұрын
Sorry, just didn't have time for that. If you look at the groupings that I placed in the description it shows you which wires to connect together. Not a diagram but if you match the colors/polarities it'll work.
@JawadAhmadsahibzada 2 жыл бұрын
@@RunPlayBack thank you, i will try that
@gargoyle67 3 жыл бұрын
What front wheel stand is that ?
@RunPlayBack 3 жыл бұрын
amzn.to/3vr9kjn
@ornn6177 Жыл бұрын
can you do this with just a headlight no break or indicators
@RunPlayBack Жыл бұрын
Yes, the same concepts apply, doesn't matter how many or less lights you have.
@Michael-sc7yt 2 жыл бұрын
What do you mean by "the original controller is too small"? You mean the power of the motor is bigger than the controller's ability? so upgrading to the one with bigger current limiting can make the controller cooler?
@RunPlayBack 2 жыл бұрын
Sorry it's been awhile since I made this. Do you know where exactly in the video I said that?
@Michael-sc7yt 2 жыл бұрын
@@RunPlayBack You upgraded the original controller to a new one and said the old one is easily getting warm.
@Michael-sc7yt 2 жыл бұрын
@@RunPlayBack from 23:58 so you upgrade the controller to a bigger one with more mosfets?
@RunPlayBack 2 жыл бұрын
@@Michael-sc7yt oh okay..that's not the controller, it's a 12v step down converter that's connecting directly to the battery and converting the voltage to 12v. The 12v step down I have listed in the description can handle a 72v battery. It has nothing to do with the motor or the ebike's controller.
@davidrivietz3742 2 жыл бұрын
But will it hold up in the rain?
@RunPlayBack 2 жыл бұрын
yeah it should be fine
@travislatrelle2599 Жыл бұрын
So where would group d and f negative wires go?
@RunPlayBack Жыл бұрын
Any negative lead, should connect back to the main ground/return wire back to the power source
@timmywitaburner3698 3 жыл бұрын
Does anybody know the intro song name
@NirvashOne Жыл бұрын
I wish you would have went more in depth on the flash relay. I didn't quite understand what you were talking about. Good video though
@RunPlayBack Жыл бұрын
Thanks for watching! What exactly didn't you understand ?
@NirvashOne Жыл бұрын
@@RunPlayBack how the flasher relay is wired in the circuit
@RunPlayBack Жыл бұрын
The flasher relay is typically wired in-line to the positive wire before it goes into the blinker switch.
@NirvashOne Жыл бұрын
@@RunPlayBack thanks man I really appreciate it I didn't even think about having it before the switch.
@THENEWWRANGLER 3 жыл бұрын
Can u make me this set up to run on my rose ave i will pay,
@stephengauntt574 2 жыл бұрын
How much did the whole setup cost
@RunPlayBack 2 жыл бұрын
Not much..probably around a $100 or something.
@stan121midling5 Жыл бұрын
@@RunPlayBack cost a lot more then that now hehe
@whatis4566 3 жыл бұрын
WHEN IS THE NEXT VID
@RunPlayBack 3 жыл бұрын
This week!
@alohaemeli 3 жыл бұрын
Isn't that the S1 though?
@RunPlayBack 3 жыл бұрын
Nope that's the Z1
@kjm-ch7jc 2 жыл бұрын
Looks complicated also might not conform to individual countries regulations.
@RunPlayBack 2 жыл бұрын
Okay?
@bobcatt2294 Жыл бұрын
A switch installed inline interrupts the flow - usually the hot side. You state that the switch you connect positive to one and negative to the other - this is absolutely wrong. see at: 4:23.
@RunPlayBack Жыл бұрын
You're correct, that's a good catch!
@protonspring5244 Жыл бұрын
Not "sole--dur,". . . "saw-dur"
@RunPlayBack Жыл бұрын
Depends on if your British or American. Where you from?
@protonspring5244 Жыл бұрын
@@RunPlayBack U.S. Wow. . I had no idea. Everyone outside of America says "sold-rrr?" Why we always gotta be different. lol
@RunPlayBack Жыл бұрын
@@protonspring5244 Hah yeah..and I don't know why I pronounce it the British way. Maybe I watched some tutorial from the UK or something and it just stuck with me.
@richardha1502 3 жыл бұрын
Any chance you could tell me how to install led turn signal strips on my onyx side panels? www.amazon.com/gp/product/B07RWBWT55/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 i just can't tell which color wire is for which. i'm thinking once i know that i can just wire tap into it.
BalcevMMA_BOXING
Рет қаралды 21 МЛН
Eat Travel Roll
Рет қаралды 19 М.
chooch tech
Рет қаралды 895 М.