a local shop estimated me $600 to clean out a tank on my Honda that has been sitting for 3 years!! I can do this myself...THANKS!!

seriously thank god i found this channel its seriously one of my favourites not only do you make helpful videos but you add amazing humour to it. This is how people need to make videos hope you blow up even more :D

What I do for dirty tanks but can also work decently for rust is dump in a few hundred to about 1000 bbs depending on the size of the tank and spray in a good amount of carb cleaner and shake the tank. Bbs are cheap for you non gun owners you can buy several thousand for about $10 this works better then nuts or rocks. Also they are only .177 of a inch in diameter so they can get into almost any spot in the tank to knock crud loose

You don’t need to neutralize the acid with baking soda. Simply rinsing it well with water will get rid of the acid.

I always make sure to use Red Kote on the inside of the tank after the vinegar treatment for the rust. The Red Kote will seal the inside of the tank and prevent rust from happening again.

Awesome video, definitely saves me from buying the more pricey kits from the local moto shop! Thanks Sparky!!

You are a funny guy with good tips, thank you. No bullshit, so nice

You need to get a light. You don't need to neutralize vinegar, just rinse with water. Alcohol does not absorb water it displaces it because it is heavier than water. You can use an air hose, a hair drier, or even a heat gun.

Nice job my Friend!!

I just found your channel. I come from Bikes and Beards. I love how your tools match the lines on the wall behind you. 😂 Great video. Keep it going.

MUCH BETTER METHOD: If tank interior is heavily rusted then fill tank 1/2 full with abrasive or clean gravel. Double seal all holes with Duct tape and rubber compression plugs. Wrap tank in two heavy moving blankets and rope or zipties. Then tumble tank for 2 -5 hours in a clothes dryer to remove all loose scale. Tumbling is a slow process. Then wash inside of the tank with a Degreaser like 409 and distilled water. Rinse well. Evaporust is reusable, no odor, nontoxic and does not harm metal or paint. So Evaporust in the long run is way cheaper than one use vinegar. Evaporust will not cause flash re-rust if you rinse with distilled water. Let dry and treat with interior with OSPHO. Ospho is also reusable. Ospho is special mild Phosphoric acid that turns the metal surface into Iron Phosphate. Iron Phosphate will not rust. Rinse well with a gallon or two of Distilled water. Use a hair dryer to dry out the tank fast. Seal the tank: Plug all holes except one. Fill tank with 1/8 to 1/4 full of silver or white POR. (Do not use black POR) Rotate the tank several times to coat the inside and dump out the excess POR. Let harden overnight. WILL NEVER RUST AGAIN. Exterior: Wipe with Ospho Three times. then apply POR. NOTE: Tap water has minerals that promote the formation of rust. DO NOT USE TAP WATER.

Use the blower end of a vacuum cleaner or a hair dryer to blow dry the inside of the tank.

Funny video. I'm going to use your method😎

there’s a new fangled thing called a flashlight that you can shine into the tank so you can see e the full effect.

Very nice vid only thing with me I noticed that if I left the vinegar in for about a week it was less likely to flash rust as compared to a few days.Oh and the nerf missile firing bike you made for bikes & beards was unbelievable !

Love your energy and helpful advice. I'll keep watching as long as you make these!

I am thinking of doing electrolysis and immediately flushing with gasoline/alcohol, emptying, and filling a thing or two of marvel mystery oil in and then finally shaking and draining. thoughts?

Your best video yet, Cousin.

You drinking vinegar convinced me to turn all notifications on😂

Sand in the tank. Attach a hand sander on the outside. The vibration will sand the rust.

My nose hairs burned just watching you drink that total, complete, entire gallon of vinegar

Nothing beats vinegar, baking soda. Don't forget to rinse it with distilled water

After removing the rust. How can I preserve the inside of the tank if It weren't to be used for fuel?

30% vinigar works great

Helpful AND Hilarious! Love it! Thanks Sparky 😊

Welp the washers and what not was a great idea. Got antly great ideas ad y9 how to remove them from a VTX tank afterwards. A magnet is working out and i cant seem to get at em with a shop-vac hose. Its an 1800 V-twin with Vance & Hines drag pipes...she gonna sound like a baby rattle at stop lights😅

Thanks for your nice video .for drying water, you may can use hairdryer.

How much baking soda per gallon? I have a 5 gallon tank

Make for us a custom ABS gas tank please.

Great editing!

Lol he's like more ingredients we can drink 😂😂😂alcohol

“and whats coke without rum…” you funny

So someone told me to use baking soda with vinegar to clean it. I guess because the fizz helps idk but I just put four gallons of vinegar in my tank and while adding some baking soda I thought to myself "wait a minute if it neutralizes the acid.." Did I just waste 4 gallons of vinegar because I neutralized it with baking soda and now it's not going to work?

Thanks…

Coca cola is realy expensive in my country haha

Don't they make a sealant to go into the tank after the clean up to prevent rust.

Gotta try molasses!

Use electrolysis.

Why does this guy’s vids not play nice? WTF?

😅😅

just do it..attempts at comdey slow it down too much.