Brian, I am happy you posted this video. After I watched your first video on mounting solar panels on channel strut, I decided to do the same. However, after speaking with a professional installer, I opted to drill a few holes to provide additional support. The installer said he had seen panels detach from RV roofs, particularly rubber roofs. Also, I spoke with 3M engineers who said 3M did not recommend using their VHB tape for solar panel roof mounting since they had not done the type of testing necessary to validate its suitability. In addition, I leaned there are several types of VHB tape for different type applications, some for metal-to-metal bonding, others for metal to non-metal materials, etc. 3M also recommended a primer to strengthen the bond to certain non-metallic surfaces. I used solid aluminum channel (without the slots), a 45 mill thickness VHB tape for metal to non-metal applications, a 3M primer applied to my EPDM roof, and drilled three holes in each piece of strut, one at each end and one in the middle. Everything has held up fine so far.
@RVwithTito2 жыл бұрын
Thanks for sharing that additional information. Great job!
@nipperr7252 жыл бұрын
Hi tito from the UK..was watching you putting these on , can't believe its a year ago, I'm getting old too quick 😂
@RVwithTito2 жыл бұрын
Almost a year...I installed them in late Sept but didn't release the video right away.
@portnuefflyer2 жыл бұрын
Back in my solar installer days, I was often asked to do RV installs. I did at least 50 modules of various sizes on various types roofs. My first way to do it was to work off of a roof rack, if there was one. Most often though I used EPDM rubber "donuts", 7/16" dia., that had a brass 1/4" threaded insert bonded into them. I'd bolt my stand off legs to the modules first, then when on the roof and where I wanted them (away from shadowing structures as much as possible) I'd drill thru my braket legs into the roof with a 1/4" drill, all 4, then shift it enough to enlarge the hole to 7/16", and with a twisting motion insert the rubber bushing into the roof, re-position the module, and using 3/4" stainless 1/4" bolts, torque them down. NO caulk, no leaks, and never had one come loose. I bench tested the holding power of them first of course, to prove the concept to myself. Your no fastener at all method is yet another approach. For the last 5 years or more, my go to caulk OR glue is a product called Lexal, I get it at Ace Hardware. It outperforms silicone types hands down, and it's best described as an "adhesive caulk." It stays pliable, is crystal clear (or white) and is especially rated for any plastic to any other plastic, though I use it about anywhere.
@RVwithTito2 жыл бұрын
Great info. Thanks! I found the Lexel (spendy) and will have to look into those rubber donuts.
@portnuefflyer2 жыл бұрын
@@RVwithTito They are hard to find, short of a specialty commercial hardware outfit , like Fastenal, even then you have to order them in. Lexal spendy? I like the smaller tubes, rather than the caulk gun sizes, they are less then 10 bucks I think, worth it! I have used it on my LSA plane a lot, one favorite trick is, for instance, when routing something like a GPS or Sirius SAT radio coax cable inside the cabin, rather than use mechanical fasteners of some type, I use the clear Lexal, just a dab every few inches, and some masking tape until it sets up. Next day, tape off, cable stays put and you can't see the Lexal.
@RVwithTito2 жыл бұрын
@@portnuefflyer Hmm. That cable routing idea sounds interesting. I'll have to try that. Thanks!
@MingoMoon2 жыл бұрын
Thanks for the update, it’s always great to hear how things are working almost a year down the road. Great job and great video
@RVwithTito2 жыл бұрын
Glad you liked it. I'm glad things are holding up well.
@ronb805211 ай бұрын
Tito: thank you for your never-ending ideas. I'm grateful to you for your idea of mounting flexible panels on the corrugated plastic cardboard....a brilliant solution!
@joniboulware1436 Жыл бұрын
VHB worked well for us. We did not need track but had extra large brackets. We even had ours set a little high to ensure the panels didn't overheat. Did the whole Alaska loop over 5 months and all was well.
@RVwithTito Жыл бұрын
Nice! Good to hear.
@josephmarc62632 жыл бұрын
Tito, I used your last system (aluminum T-track and VHB tape) to install 850 watts of solar on my Leisure Travel Van and after 30,000 miles it was still solid. I did add a few bolts in strategic spots where the T-track didn’t perfectly follow the curve of the roof. With 8000+ watt-hours of 24v lithium BigBattery and the converter from the alternator, I could go indefinitely without plugging in. I didn’t even have a generator on that rig. Thanks for the great insights!
@RVwithTito2 жыл бұрын
That's nice to hear. I appreciate that 30K miles follow up. Great job!
@joeboxter3635 Жыл бұрын
How do you bet 8000wh out of 850w. That'd be 10 hours of sunlight and 94+% effective.
@josephmarc6263 Жыл бұрын
@@joeboxter3635 Over a 24 hour period, we typically run the batteries down about 15%-20%. During the day, we charge batteries from the chassis alternator (about 40 amps) and the solar arrays (the 850 watts usually produces 300-500 watts in most conditions). With a few hours of driving and/or some decent sunlight, we get that 20% back within four to six hours. We’re essentially able to go indefinitely without shore power. Of course, running the AC changes everything. I get 2-4 hours before the batteries are depleted with the AC running.
@herb78772 жыл бұрын
I started watching you ~6 years ago as I was learning about solar. I did a “chase the sun” system out of fear of drilling holes & leaks. I applaud your experience and follow up. I am looking at a permanent installation on our new tt but very cautiously evaluating which way. Thanks again for the follow up.
@RVwithTito2 жыл бұрын
Thanks for following along. Good luck with the project!
@Ms.Frankenbuilder2 ай бұрын
Rainy day, good chance to catch up on my favorite you tubers. Impressive results on that system.
@RVwithTito2 ай бұрын
Enjoy! 😊
@danielquinn1532 жыл бұрын
Tito your an excellent Mechanic in whatever you do. You remind me of myself I like suspenders and a belt when your mounting something like that to the roof ya never know. Thanks for all your very detailed videos
@RVwithTito2 жыл бұрын
Thanks!
@toddshook176528 күн бұрын
Glad you posted follow up video. Glad it still hanging in there. Thank you.
@mrpizzalv6 ай бұрын
Very nice DIY install. I like to see the innovation of using other parts in different systems. Love the tilt option. Great job.
@RVwithTito6 ай бұрын
Glad you like it! That tilt option makes a big difference this time of year.
@SN-qu2gz Жыл бұрын
Paul Simon's illegitimate son can really rock the solar! Cheers!
@RVwithTito Жыл бұрын
That's a first. I can see it 😀
@dalemajesticwandarer2 жыл бұрын
Always impressed with your projects, and innovative design and installs. Glad to hear it held up so well and just proves you really know what you are doing. Nice job and thanks for the videos.
@RVwithTito2 жыл бұрын
You bet. Glad to share :)
@lylestavast76522 жыл бұрын
Genius little rain gutter hijacking there ... that was good thinking...
@RVwithTito2 жыл бұрын
Thanks. Only $5 for the 8ft section of gutter.
@DirectCurrent4u2 жыл бұрын
Your solar panels look really nice Brian. They're never gonna go anywhere! I'm glad they're working out really well for you. Keep up the great work and please stay safe and healthy God bless.🙏🏻👍
@RVwithTito2 жыл бұрын
Thanks. Yeah there solid.
@anthonyb2334 Жыл бұрын
Thank you for another great video. Living in Arizona, I’ve always been afraid to glue things on /down for fear our extreme heat will loosen it up. I love the way you describe things. Thank you again.
@IFLYRace512 жыл бұрын
I recently did the same with strut and VHB tape, added 3, 210 watt panels, but I did run a few large screws to each rail. I used silicone rubber to secure each long side.
@RVwithTito2 жыл бұрын
Great. Hope they last a long time for you.
@edfig_76 ай бұрын
Hi Brian! I’ve been watching your vids for a couple years now. I thought I was already subscribed, but turns out I wasn’t, so I just subscribed! I always come back to watch some of your older vids, like this one, because you do a very thorough job of describing your DIY process. Thanks again and I hope your rv solar system is still holding up well. Take care and keep doing what you’re doing. God bless!
@AByrne2 жыл бұрын
I love your channel. You’re so friendly and your information is useful.
@RVwithTito2 жыл бұрын
Awwe :) I appreciate that.
@jorjimaco5331 Жыл бұрын
Good job, solar controller for each panel. Perfect. Victron rocks….👍
@RVwithTito Жыл бұрын
Totally agree. Once you go blue, eventually everything turns blue.
@jorjimaco5331 Жыл бұрын
@@RVwithTito 🇦🇺 plenty of sun down under. Yep I’ve turned blue as well, I’ve done exactly the same thing with my solar, but I use ground panels because I park in the shade. It gets hot in AUS. 🍻🌮
@TheRayDog Жыл бұрын
Such great ideas and clever building. Not to mention good video footage and editing. Thank you!
@RVwithTito Жыл бұрын
I really appreciate that. Thanks!
@eventhorizon51833 ай бұрын
I'm glad u put the scews in your roof. No matter what, relying on just adhesive strength is risky, especially for this application. Also, high quality stainless steel mounting hardware and tilt bars can be purchased from AM Solar.
@djwaffle Жыл бұрын
I love how you did this. I have a rubber roof so I'm going to have to drill but am going to do it at the ends and middle where I can on the long side. I'm also going to skip most of the tape and raise my mount rails a little for water run off. Awesome video, thank you.
@vaasnaad Жыл бұрын
Thank you so much for this follow up! Loved the idea so much I'm doing something almost identical with residential panels on my travel trailer.
@RVwithTito Жыл бұрын
Glad it helped. Good luck. I'm doing another one on my garage with the extra panels I have. It should power my shop no problem.
@stevekrud2715 Жыл бұрын
Tito I too added screws almost right away after using the 3M tape. Though the tape will not let go I started seeing videos of winnebago roof repairs where the layers separated in the wind or going down the road. I also thought the panels would put even more force helping cause a separation. So I added a screw to each panel leg
@RVwithTito Жыл бұрын
Yeah. I feel better about it now...same reasons.
@brotherkith2 жыл бұрын
I've used Silicon mounting pads for many years on several trailers that travel year round. Never had any issues at all.
@RVwithTito2 жыл бұрын
Great to hear. I can't see these coming off without my help.
@lau5862 жыл бұрын
Thank you very much Tito, I am at that stage in my RV and the video has been very illustrative.
@RVwithTito2 жыл бұрын
Great to hear. Good luck with your projects.
@FMTFXE222 жыл бұрын
You are amazing, you think about everything. Please open up a custom upgrade gadget install shop.
@RVwithTito2 жыл бұрын
I wish. Can barely get my RV down our road :)
@rockeyoliver72542 жыл бұрын
Awesome video Brian! Thank you!
@RVwithTito2 жыл бұрын
Glad you liked it!
@coachgeo8 ай бұрын
hmm.... for solving some issues like: - having options to re-do panel configuration in future, - better height for improved hot air escape etc. P/Starb + B/Stern mounting solution- might could solve above - Permanent Base Rails @ P/Starb direction : mount like you did; one's chosen rail system, across roof in Port to Starboard direction (P/Starb) at a measured planned distance apart... say from bow end of roof, bond permanently rails in P/Starb direction, every 2 feet? Do this all way to the back Bow to Stern. - Reconfigurable upper rails @ B/Stern direction : atop Permanent Base rails; using that rails bolt on mount system, place sections of rails that run Bow to Stern (B/Stern). Place these sections to match where needed for panel mounting, All the panels etc. are mounted with these upper B/Stern rails. Bolt atop the Base; where needed, some small P/Starb, or B/Stern sections of rail , to use for clamping the panels on an edge where needed. Now your panels are further off roof by 0.50 to 0.75 inches than just one rail as you did . This should aid heat escape issue.. AND best of all... now your panel lay out is completely reconfigurable. Just unbolt Bow/Stern rails from their Permanent Base Rail and move them, and the panel attached to them, to where newly desired. Hmmm on second thought. for those with curved RV roofs etc.. the Permanent base rails going P/Starb may need to be in sections and not one rail all the way across in order to help deal with the curve. ... or guess one could slice the vertical sides of Base Rail in a few places allowing one to bend the bottom face till whole thing matches the roofs' curve. Luckily a problem I wont have with my Ambulance boxes flat roof..
@JulGarbacea782 жыл бұрын
Hi Brian! Thanks allot for the update, Thanks to you I'm planning to add a solar sistem on my Semi Truck cab. Please keep up with the great projects you do.
@RVwithTito2 жыл бұрын
Awesome. Good luck! Have you considered Merlin solar merlinsolar.com/tractor-semi-class-8/
@toddincabo Жыл бұрын
👍 Nice job, thanks. I plan on doing that very same mounting technique as to allow for some of those appliance lifting air bags to be utilized underneath the panels (cross member mid way with plate) to raise the panel. A spring or springs would work to keep the panel wind safe while stationary and some quick type of lock downs for traveling. As you have two rows of panels a simple selection valve at the air pump would suffice. Combine the air bag release tubes together and have a single going to a convenient place to lower. A proper timer to the pump could be programmed for it to "follow" the sun, and just drop them back down in the morning.
@mendocinorider2 жыл бұрын
Looks good, I also purchased a newer rv and have to do this job over.
@RVwithTito2 жыл бұрын
Good luck. Sometimes it's nice to apply new knowledge to a new project though.
@rogerspalding56732 жыл бұрын
Brian, the slope to the roof to which you referred is called "tumblehome." At least, that is the engineering term used in the automobile industry. You will make yourself clearly understood when discussing this aspect of your vehicle with automotive engineers and designers.
I think you did a good job, long rail fitted with a good glue all the way that will make a strong attach to the roof.
@RVwithTito Жыл бұрын
Thanks. I think it's held up pretty well and we've been through some extreme conditions.
@mikewatkins978 Жыл бұрын
Hi Tito, guess my other comment on the first install of these panels hasn't been read but you've done what I saw as a potential lift and your solution of the leading edge baffle in a word, excellent! Unfortunately to tilt the panels means a trip to the roof each time, this is where the solar panel side shade idea you had would be less work to aim at the sun and keep the side of the RV cooler being shaded by the panels. The side mount with your baffle is just getting better, I finished my initial lithium battery install yesterday so my project is moving forward. Thanks for your tips and insight.
@daviscrt2 жыл бұрын
Great update. Looking forward to the next video. Thanks Don
@RVwithTito2 жыл бұрын
You bet
@CurtDanner Жыл бұрын
You did a really great job and put a lot of thought into it. Thanks for sharing.
@RVwithTito Жыл бұрын
Thanks for watching!
@KayVASolutions2 жыл бұрын
Great video! I like that clean look also. You can't tell that you have solar panels on the roof. Great job!
@RVwithTito2 жыл бұрын
Yes! Thank you!
@center_of_mass7 ай бұрын
Wonderful! I need a list of all these staff ;)
@gordschultz19802 жыл бұрын
Great update video. Like the small changes you made.
@RVwithTito2 жыл бұрын
Glad you enjoyed it
@1951Roy2 жыл бұрын
Thanks, that was a great review. Happy camping.
@RVwithTito2 жыл бұрын
Thanks!
@cornwallav8r6 ай бұрын
Very cool, just one note....ANYTHING not aluminum or s/s will soon enough drip rusty lines down your RV if not handled...
@housesOTR2 жыл бұрын
Thanks again for all you do for us. God bless
@RVwithTito2 жыл бұрын
You bet
@weasleyoc2 жыл бұрын
Just a comment on the wind baffles. We lost one panel in the desert because the wind came from the rear end of the trailer. Blew it right off.
@RVwithTito2 жыл бұрын
Yikes. We've been in some heavy gusts as well. Luckily dirty is all we got.
@heavenonearth99592 жыл бұрын
Definitely do that video on your setup…
@sarahfryman Жыл бұрын
Very nice setup. Thanks for sharing.
@RVwithTito Жыл бұрын
You bet!
@lrobie1232 жыл бұрын
well done explanation. no annoying music either
@johnnysweekends2 жыл бұрын
Good job Tito love the channel. Hope to see you on the road sometime. I’m on the west coast..👍🏼
@RVwithTito2 жыл бұрын
Thanks. Glad you enjoyed it. If you happen to see us, say hi!
@timmysrvlife Жыл бұрын
You and other few KZfaqrs inspired me do a big solar install of 3800w with sliding panels. I also used VHB tape and later found need a few screws. But with my 3800w, the best I have ever seen is about 2000~2500w.
@stargazer7644 Жыл бұрын
Cosine error will kill the efficiency of a flat roof solar install especially in the winter. The panels need to be facing perpendicular to the sun for full output. You’ll lose 30% of your power at a 45 deg angle, and 65% at a 20 deg angle.
@timmysrvlife Жыл бұрын
@@stargazer7644 I understand. That's for sure in winter time. But the number I refered to (2-2.5 kw) is in summer time which the cosine error is relatively small. Recent days (November), I am getting only 1600 to 1800w now. 😅
@stargazer7644 Жыл бұрын
@@timmysrvlife Are you using an MPPT (tracking) controller? That will also make a significant difference. Make sure there are no shadows at all on your panels. Even just the slight shadow of a power line or a guy wire or antenna or bird droppings across any part of a panel will drastically reduce the entire panel (or string) output by partially shading one or more cells since they're in series.
@elaineg49212 жыл бұрын
Fantastic , looks great. Blessed travels
@RVwithTito2 жыл бұрын
Thank you! You too!
@thomaskeen7782 Жыл бұрын
Yes on rubber roof didnt feel confident with just VHB tape. my roof has 1/8 inch wood substrate. Screws have torn out under high wind. So I use Well nuts that grip under the surface of the wood and tpo. So far excellent with the T track.
@allankawakami2 жыл бұрын
Always good information! Thanks Brian for sharing 🤙
@RVwithTito2 жыл бұрын
You bet!
@Darren43522 жыл бұрын
I'm glad I saw this video! I saw your earlier one and was all set to do a no drill mounting of my panels but then I saw this one and you mentioned the delamination problem that I would run into with the rubber roof. I guess I'm just not feeling great about the idea of having to drill 48 holes into my roof instead of using the strut channel solution.
@RVwithTito2 жыл бұрын
Yeah. The track is a great solution for multiple panels and also allows for greater flexibility down the road. Good luck!
@adowdell2 жыл бұрын
It's hilarious you just posted this, I just bought some panels and will be putting some money into my RV and was wondering how this system aged.
@RVwithTito2 жыл бұрын
Funny. Great timing :) I'm hoping this lasts a long time and don't see why it wouldn't.
@rigsnrvs2 жыл бұрын
Brian, great video. Thank you for posting your diagram for download- I just got it. I’m looking at putting the sore on my fifth wheel now and have been trying to find a high power solution what’s up having solar panels everywhere. Thank you for all you’ve done
@RVwithTito2 жыл бұрын
Great! Let me know if there's something missing from the diagram or equipment list. I'll try and keep it updated.
@5markbennett2 жыл бұрын
Nice clean set up.
@RVwithTito2 жыл бұрын
Thanks!
@brianbelliveau5551 Жыл бұрын
Nicely done ✔️
@RVwithTito Жыл бұрын
Thanks!
@rikmorel48702 жыл бұрын
Thanks for the video! It was really informative and is exactly what I plan on doing with my smaller camper RV that i'm building.
@johndavid96332 жыл бұрын
Hi Tito, great update video thank you 👍
@RVwithTito2 жыл бұрын
My pleasure!
@carykern60799 ай бұрын
Excellent!!
@RVwithTito9 ай бұрын
Thanks!
@digger105337 Жыл бұрын
Lock washers next to the bracket are pretty useless(if not counter productive) on the bolt head in a pivot. L washers are meant to dig in to stop rotation. I would suggest going with nylock nuts instead. ( A locknut with a nylon insert) and ditch the lock washers in that situation. A flat washer in place of the L washers would be a better arrangement. If you used nut-serts in the panel, a dab of blue lock-tite would be appropriate.
@brianchetelat6601 Жыл бұрын
Great job Brian but I was expecting that from you : )
@RVwithTito Жыл бұрын
:)
@kaycoffman57982 жыл бұрын
We need more RVs that are entirely off grid; more solar, larger battery compartments, larger propane containers, recycled water system for the grey tank (sinks, shower, washer) that reuses the water and filters it (easy cleanable filters), air to water systems that generate 5 to 10 gallons of water a day (filtered), "Cinderella Propane Incinerating Toilet or Composting Toilets (get rid of black tanks)" hot water on demand, mini-wood stoves with electric heating to reduce the massive condensation from propane heating, and more.
@stahpit1971 Жыл бұрын
I like the idea of no drilling but eventually the adhesive will give up due to temp changes. Even tiles on the shuttle eventually came loose. I would have a safety leash for when they come loose so no one dies on the highway.
@kenkiekens77462 жыл бұрын
At 14:20 it shows 4 MPPT, 36w, 31w, 113w, 223w. these are the 4 MPPT 100/50. what if you bought two MPPT 150/35. if two of the solar panels are put in series the current would remain at about 11 A. but the VOC would be about 49.1v + 49.1v. = 100 v. The MPPT 150/35 would give room to grow in case you replace with 490 w or above. The panels in series would be the ones with 36w panel + 113w panel (giving the MPPT a chance to work) perhaps bringing them both above 100 w giving 200 w. I'm assuming the 36w panel is being shaded in some way of course!, but the MPPT would bring voltage up! This is a test you could do. Most don't understand what I'm suggesting here and may sound nuts, but that is what MPPT's are supposed to do. you can test it. So on a day where you get 36w, 31w, 113w, 223w. you can video the wattage like normal. Then disconnect all MPPT, connect the panels giving LOW and HIGH voltage in series, and install the two MPPT 150/35. So two panels to one MPPT and the other two panels to the other MPPT making sure the panels giving the low voltage and high voltage are put in series. and see what happens.
@RVwithTito2 жыл бұрын
The video clip you mention was on a day parked in the woods (heavily shaded - future video). I just added it here to show the display. Definitely not normal conditions. These are 425 Watt panels with over 70VOC each and a potential output current (after MPPT) of around 46A at 12V.
@SaltyCLE2 жыл бұрын
Brian, Inspired as always
@RVwithTito2 жыл бұрын
:)
@working1972 жыл бұрын
The next time you drive through Central Texas - hit me up (alternative motive) and help me do this to my RV. 😄😁
@RVwithTito2 жыл бұрын
Do people just happen to drive through Central Texas? Just kidding :)
@Mike-01234 Жыл бұрын
Actually think your tape method is stronger then using wood screws into that thin plywood.
@robertthompson69582 жыл бұрын
Very inventive.
@RVwithTito2 жыл бұрын
Thanks.
@marleroma36817 ай бұрын
❤l love it! Great video. I'm definitely going to try it.
@Technodude255 Жыл бұрын
Love your vids! Super useful!
@RVwithTito Жыл бұрын
Thanks for watching!
@coreymerritt77422 жыл бұрын
That’s great Brian I’m glad it’s working well very nice setup that sealant you were using in that bag what was it I’m curious thanks 😊
@RVwithTito2 жыл бұрын
Someone recommended I try it a while back instead of Dicor. So I have been. Here it is: amzn.to/3wU5UJt It works just as well plus you get more and it stores easily for repeat applications.
@tdknucklehead9416 Жыл бұрын
Brian, thanks for this great info. I’ve noticed that there are many versions of VHB Tape. Could you let us know which model of tape you used? Thanks again.
@RVwithTito Жыл бұрын
I used 1.5" RP62, but it's really hard to find now unless you buy in bulk (amzn.to/3Ywprfi)
@lindanadaud96982 жыл бұрын
Great video. Thank you.
@RVwithTito2 жыл бұрын
Glad you liked it!
@jmr8111 Жыл бұрын
Great info Tito , Im a new subscriber here and enjoy how you lay out the info and back it up with great camera shots of the installs and equipment /tools needed etc. I don't think most people realize how much work goes into shooting and editing a well made video takes . I have a 2000 Monaco Diplomat that has a thin aluminum roof very similar to the construction of the Winnebago . I had 3 panels (130 watts each lol) installed maybe 12 yrs ago . They were attached with just the Z B rackets and although still in place you can PULL up on them and feel the roof move . Im thinking about upgrading the panels and patching the old holes and using the STRUT channel VHB tape . Going from AGMs 900 amp hr to at least an 800 amp hr Lithium bank . I like the battle borns but was also considering the new 330amp Victrons Lithium . Seems hard to find many reviews on Victron batteries but everyone uses all their other electronics? Thank you for well made content J. USMC
@RVwithTito Жыл бұрын
Hey there. Welcome! Don't know much about Victrons batteries. What I do know is that the BMS is a separate piece of equipment. So don't forget that piece. 👍
@jmr8111 Жыл бұрын
@@RVwithTito Sorry called you Tito , Thnx Brian
@GaiaCarney Жыл бұрын
Great information, thanks for sharing 🕊
@razaldaznscale34562 жыл бұрын
Wow, love your vids thank u for what u all do.
@RVwithTito2 жыл бұрын
I appreciate that. Cheers.
@stewartmhyre15282 жыл бұрын
Brian, another great video. It doesn’t look like you have air conditioners up on your roof. Is this so? Did you remove them? How do you deal with the heat? Looking forward to seeing your video on your other solar components especially how the Multi Plus II has performed.
@petercolquhoun20862 жыл бұрын
The Adventurers of this era had basement A/C units.
@RVwithTito2 жыл бұрын
Peter is correct. Our A/C heatpump unit is in the basement. That was a feature I really love about this rig. In case you're wondering...yes I can run the A/C with my setup. I don't even need a soft start to fire it up.
@stewartmhyre15282 жыл бұрын
@@RVwithTito wow I didn’t know that was something they did. I wonder why there was a change to roof top units
@RVwithTito2 жыл бұрын
@@stewartmhyre1528 It's great, but everyone asks..."what's that in the back?" It does limit the amount of storage space you'd have I suppose.
@dewholdingsllc10502 жыл бұрын
@@stewartmhyre1528 Coleman basement AC has two compressors, and most RV builders bolted them in not a slide out rack for repairs and cleaning and service. They are not easy to drop and repair. Also AZ Expert has shown his channel over the years they have had circuit board issues and updates. Not a lot of room to work.
@augustinebaerga75564 ай бұрын
Have you noticed any water pooling next to the struts causing a dam effect? I’m thinking about doing this, but raising the struts 2/4 inch using washers under the attachment points.
@timf69162 жыл бұрын
Nice, Good job. You still have FREE Labor for installs. Hehe
@RVwithTito2 жыл бұрын
She's available when needed :)
@kristenwesche2207 Жыл бұрын
Thanks for the great videos! Just curious what size mounting brackets you used initially and also on the higher ones you updated in this video? Thank you!!
@RVwithTito Жыл бұрын
The smaller ones were about 2" and the larger ones were about 3"
@ronwasser23852 жыл бұрын
Great info thanks👍👍✌️
@RVwithTito2 жыл бұрын
No problem 👍
@dominique___1980 Жыл бұрын
Gracias, Tito~!!
@davesigz2 жыл бұрын
Nice job
@RVwithTito2 жыл бұрын
Thanks!
@ManWander2 жыл бұрын
well done!
@RVwithTito2 жыл бұрын
Thanks!
@noeleenfalkner45572 жыл бұрын
Thanks for your video Brian always lovely to see what you guys are up to. Do you have a video on how you mounted them and how did you store the battery backups for the solar panels. I am in Auckland New Zealand living in a Cottage from Cedar Creek USA so solar panels would be really great I am stationary I cannot tow the semi-trailer around New Zealand it would need dealership plates for that
@RVwithTito2 жыл бұрын
Yes. There's a series of videos for the project here: kzfaq.info/sun/PLIsusUNNN2JYhtQFQSPp3FkVXLXZLApM-
@Mike-01234 Жыл бұрын
Was wondering why you didn't just use one of the K2 system rails which are aluminum made for home rooftop solar. Price is about the same as the rails you got from Home Depot. Santan solar sells the K2 system made for bolting down to metal roofs called the MiniRail XPRess.
@renegadecampervan50178 ай бұрын
I only realised recently that the single solar panel on my motorhome has just been glued down with no drilling. Its a 2008 model motorhome. I wish i knew what adhesive they used.
@paulscott95622 жыл бұрын
I didn’t have as good success. I followed your previous install with flexible panels to the T and first trip out 2 days ago lost a solar panel on I5 south near Toledo WA.
@rider893 Жыл бұрын
Thanks for the update, doing the same. appreciate your insights
@tombeilman55792 ай бұрын
Looks like you were in Quartzsite
@ralphballtrip2214 Жыл бұрын
I just found your video and thanks for your video. It’s I’m getting ready to buy a Provo 1980 or 90 and I want to put a solar panel on top like yours. Where did you buy yours at if you don’t care did gonna be 40 or 45 foot?
@RVwithTito Жыл бұрын
The solar panels? I got them from SanTan Solar in AZ.
@nipperr7252 жыл бұрын
Sun power are doing a Maxeon 6 now tito
@RVwithTito2 жыл бұрын
Nice. I heard Maxeon (the company) is selling their own panels now.
@robertp2552 Жыл бұрын
This is great :D Thank you :D
@BillButtrill Жыл бұрын
I just checked out SanTan and am overwhelmed by all the different types of solar panels. Can you make a recommendation and why you chose that brand?
@RVwithTito Жыл бұрын
I chose SunPower because I'm familiar with the cell technology and quality. I've seen them come and go from the used SanTan stock and debated on buying more. I'm not familiar with the other used inventory and their used. They do have spec sheets for their panels and also provide a one year warranty on all of their used panels. I also researched the specific panel and manufacturer to see what others said about them. Some folks have told me that Canadian Solar is a good quality and inexpensive option, but I don't have any first-hand experience with them. One recommendation is to pick them up in Arizona or Georgia if possible. You'll save a few hundred bucks in freight chargers. Good luck!
@2LStews11 ай бұрын
Ok, so, another year in ..... How is it all holding up? Still happy with the VHB tape? and problems with the install? TIA!
@RVwithTito11 ай бұрын
No issues. Holding strong after Alaska to Southern Baja and back.
@VincentandKarisRVAdventure4 ай бұрын
Do you have an idea of the total cost to do this? Thank you. Great video
@dirtroadsailing64182 жыл бұрын
Thanks for the followup, I plan on putting solar on my motor home whenever the heat breaks, and I'm going to follow your idea. Just out of curiosity, did you just put the screws in out of an abundance of caution, or were starting to notice some delamination of the filon or the unistrut? I really don't want any holes in my roof, even if I have to put more unistrut on it.
@RVwithTito2 жыл бұрын
Just out of an abundance of caution since I knew we'd be hitting some major bumps up north. I figured a little anchor on each end couldn't hurt.