Ryobi 3300 PSI Pressure Washer Won't Start

No video

Ryobi 3300 PSI Pressure Washer Won't Start

Рет қаралды 36,726

Күн бұрын

Troubleshooting a Ryobi 3300 PSI pressure that would not start. After removing the old gas and adjusting the pressure the pump build, the pressure washer is now ready to clean this summer.
Thank you for watching. If you have any questions please comment below.
#smallenginerepair
Patreon: patreon.com/us...
TikTok: / smallengine
Join our Discord server: / discord
Facebook: / coloradospringssmallen...
Instagram: www.instagram....
Small engine repair in Colorado Springs, CO that works on lawn mowers, tillers, generators, snow blowers, chainsaws, weed eaters, leaf blowers, augers, go-karts, and mini bikes. We provide tune-up, blade sharpening, oil changes, spark plug replacement, air filter cleaning, and replacement, carburetor cleaning, and general maintenance.

Пікірлер: 52

@mayerlito 9 күн бұрын

I removed the bolt from the bottom of the carburetor, drain the gas out and worked for me, Thanks Great video.

@small_engine_repair 7 күн бұрын

Welcome

@Letterstomysisters143 2 ай бұрын

Now I have to get up and do exactly what you did! Mine sounds exactly like yours here. Crossing fingers. Thank you for your video here.

@small_engine_repair 2 ай бұрын

Best of luck!

@lassotelo 3 ай бұрын

Thank you, your expertise does helped to get my Ryobi 3300psi start again.

@small_engine_repair 2 ай бұрын

Welcome

@annaweems4054 2 ай бұрын

Thank you sir, this worked for my husband’s ryobi.

@small_engine_repair Ай бұрын

Glad it helped

@gmansatx5627 10 ай бұрын

The best video on this problem.. thanks

@small_engine_repair 8 ай бұрын

Glad it helped

@moabwheeling1305 Жыл бұрын

Great video Robby ! Keep them coming buddy .Take care sir.

@small_engine_repair Жыл бұрын

Will do

@wadeshoff6071 Жыл бұрын

exactly what it was! thanks!

@small_engine_repair 8 ай бұрын

You're welcome!

@jonyi123 5 ай бұрын

Thank you, your video pinpointed to my low pressure issue!

@small_engine_repair 5 ай бұрын

Glad it helped.

@jasonbutler5936 4 ай бұрын

this absolutely works

@small_engine_repair 4 ай бұрын

Glad it helped.

@BADD400 Жыл бұрын

Good video

@small_engine_repair Жыл бұрын

Thank you.

@ajaxpsu Жыл бұрын

good video. Thanks. My Ryobi has been outside for a year in TX. I hooked up the garden hose but no water came out of the pump. What can I do? I checked the filter at the garden hose hook up.

@small_engine_repair Жыл бұрын

Tear it apart and troubleshoot or just replace the pump.

@tex24 Ай бұрын

I absolutely hate this power washer. Getting it to run without it stopping is a real pain. I saw you held the washer trigger in while starting it. I'll do that too the next time I use it. Getting it started was always a real issue with pressure building up and it dying and you wouldn't be able to pull the starter cord until you pulled the trigger to release pressure. Then when you finally get it started it dies as soon as you want to start using it. I HATE THIS THING!

@small_engine_repair Ай бұрын

The engine is good. Just might be your pump giving you issue.

@playittiltheend 2 ай бұрын

I tried everything, but what worked for me was simply squeezing the rubber fuel line a couple of times and then it started right up

@small_engine_repair 2 ай бұрын

Interesting. I wonder if something was clogged in the line?

@nivashnivash6474 Жыл бұрын

Hello how are you?......what oil do you normally use on your 4 stroke engines?....besides on a snowblower

@small_engine_repair Жыл бұрын

30w

@rogerherron5948 3 ай бұрын

I tried that, but did not solve the problem. Still no fuel coming up out of the carburetor. Something inside the carb. is stuck.

@albertodias3067 2 ай бұрын

Mine has same issues

@small_engine_repair 2 ай бұрын

Sounds like it. I clean them once and if that does not fix the issue I just buy a new carburetor.

@small_engine_repair 2 ай бұрын

Did cleaning the carburetor help?

@JRamirez9oh9 8 ай бұрын

What would be the cause of removing the oil plug and water and gas comes rushing out mixed with the oil? 😬 it’s been sitting for about 8 months still very new. Ryobi 2900psi

@small_engine_repair 8 ай бұрын

Well I need some more information to possibly even answer that. Only way water is getting into the engine case would be through the oil fill or through the carburetor, then through a valve. Are you sure it was water and not gas?

@JRamirez9oh9 8 ай бұрын

@@small_engine_repair you know could have been gas mixed with the oil. Thinking about tearing into it. Gotta learn somehow lol.

@small_engine_repair 8 ай бұрын

Gas in the oil means the needle in the carburetor is not seating. This allows the bowl to overfill and gas to leak in to the top of the cylinder. Then that seeps pass the rings and into the oil. Easiest fix it to just replace the carburetor or add a on/off valve to the gas line. When not using, turn the gas off.

@JRamirez9oh9 8 ай бұрын

@@small_engine_repair Thank you so much! Any additional steps like cleaning out anything relating to gas where the oil goes?

@small_engine_repair 8 ай бұрын

I drain the oil and let it sit for for a bit, say 24 hours, without the dip stick screwed in. This give some time for the gas to evaporate. Then add oil and run it. Then check the oil. If you still smell gas in it, change the oil again.

@donl3381 Ай бұрын

Great video. I need help. Pull start cord rips out of my hand when i attempt to pull / start it. I think its not releasing pressure and the timing is always off everytime i align it and start. Fires up but stops 10 seconds afterwards Does anyone know why and the fix? Its been a year and I'm still at a dead end. Ryobi GCV 190 3100psi 2.5 GPM

@small_engine_repair Ай бұрын

Connect the water to the pump and remove the hose for the pressure wand. Now try to start it. Does is still rip the cord out of your hand? If not, when it starts, does it continue to run? If so then something is wrong with the pump. If it still wont run and rips the cord out of your hand you need to check the valves. Remove the valve cover and slowly pull the cord and make sure the intake and exhaust valve are opening and closing. If they are, check and set the valve lash. Then try starting. I will wait to hear back from you.

@stevenwelch7401 Жыл бұрын

I’m not trying to be rude but You just turned their pressure down. That bolt was tight and it worked last year so why would you think the pressure was off instead of cleaning the carburetor jets seeings they left gas in it sitting. I had the same issue cleaned the carburetor and it started right up

@small_engine_repair Жыл бұрын

Hi Steve, no rudeness taken. In my experience if it was something with the carburetor it would not run right at any time. When the pump was not building pressure the engine ran fine. This tells me that the jets and passage ways in the carburetor are good. Like I said in the video I do not have a pressure gauge to test these. I should probably get one. So it is possible the customer messed with the settings before bring it in. I do know that after making the small adjustment on the unloader valve that the engine ran as it should under load. Again in my experience if there was something going on inside the carburetor it would not have run right under load.

@stevenwelch7401 Жыл бұрын

@@small_engine_repair it makes sense I’m just trying to learn more. You don’t learn without asking questions. Lol but I did see another video of a guy tightening the unloaded valve cause it was stalling. My pump just went on my ry80940b 3100 psi. and the pump is 150 plus tax the sad thing is I used it two seasons and the second season wasn’t a lot.

@small_engine_repair Жыл бұрын

Well that stinks!! Have you pulled the pump to try to determine what went?

@stevenwelch7401 Жыл бұрын

@@small_engine_repair I pulled the pump then checked the engine to see if it turned over and it did I did order the pump and waiting on it. Should I run the engine and make sure the shaft is spinning properly before connecting the new pump when I get it? And is there another pump with more psi I can add to my ryobi 3100psi it’s got got the Honda engine 190 2.5

@stevenwelch7401 Жыл бұрын

I got a question I have a ryobi 3100 psi 2.5 gpm my pump went. I want to more psi’s is there another upgraded pump that is compatible that I can install to get more psi’s

@small_engine_repair Жыл бұрын

Possibly. Just need to make sure it fits the output shaft and will fit in the chassis.