Muito obrigado. Minha cafeteira deu uma infestação de formigas dentro e eu desmontei sem marcar bem os conectores, mas vendo seu vídeo consegui remontar ela perfeitamente. Muito obrigado pelo trabalho

Danke. Hat mir sehr geholfen. Super 👍

Danke für dieses Video. Ich konnte unsere Saeco damit wegen defekter Pumpe vorm Schrott retten.

Hello & thankyou for your tutorial, I have a Saeco Intelia HD8752 about 11 years old with the following issue: If the unit hasn’t been used for a few hours or the power plug is unplugged and plugged back in again, upon power-up, the automatic rinse cycle starts as it should: You can hear the pump groaning, sounds like it is blocked. This automatic start up rinse is either very slow with little intermittent hot drips taking many minutes for the cycle to complete - which then leads to normal use. OR No automatic start up rinse drips and therefore the process fails entering into ‘prime mode’ which also fails & leads to an unusable ‘maintenance spanner symbol’ code 5. The only way to bypass this is to unplug and re-plug in the power plug, power-up the unit, then as it tries to perform the automatic rinse cycle, manually press the STOP option to bypass the automatic rinse and then the machine can be used as normal & makes great coffee. Note: The above symptom’s got worse after I performed a de-scale cycle, which failed at the end with of the final rinse / prime - but fully worked up until that final point. Maybe there is lime scale lodged in one of the following places: 1. Boiler 2. Solenoid valve 3. Steam & water regulator Note: This is strange because it is 100% possible to run the manual rinse cycle as per the instructions: Press the ‘pre-ground’ coffee button (with no coffee in it), then press the coffee / memo button and it does a big hot rinse no problems at all. Also, after use, when the unit is powered off, it performs a small rinse cycle with continuous hot running water coming out the dispenser, but only for a very short time. I have totally re-built the brewing unit per various KZfaq demonstrations with new stainless steel plunger screen + plunger o-ring, disassembled & blasted out all the tiny holes in the plastic plunger, made sure all the elbows and holes are clear and clean, installed the valve spring and glass ball correctly, greased all the o-rings, sliders and pivots. I have also fully taken apart the dispenser locater under the LCD display, disconnected the tube that connects to the brew unit, blasted water + compressed air through it so that it is 100% clear. Fully internally cleaned out the dispenser unit. I have calibrated the coffee grinding unit. The other issue I have is that that GREEN does not work on the LCD display - however I can still faintly see the LCD instructions - enough to get by. I haven’t run the LCD display diagnostics because that is too difficult to see / follow. But it seem like the pump + grinder & heater all work. I have disconnected & reconnected the LCD & checked the other wires, but can’t see any damage. Years ago the green would flicker on every now and then, but dead these days..

Thank you so much !!! 😀😀😀😀

Hallo, Habe auch eine Intelia Evo. Kannst Du mir viellleicht genau sagen wo der Pfeil vom Nullpunkt des Zahrades vom Getriebe hin zeigen muss wenn man es wieder einbaut. Du zeigst es zwar bei Minute 23:48 - Jedoch kann man es im Video leider nicht richtig erkennen. Habe das Zahnrad abgenommen und vergessen mir zu merken wie es gestanden hatte und weiß daher nun nicht auf welche Position der Pfeil zeigen muss.

Nabend ! Danke für das ausführliche Video! Ich finde aber leider dennoch die Lösung meines Problems nicht. Mein Display leuchtet nur rot und nicht grün. Statt grün ist es dunkel. Das komplette Display mit Bedineteil habe ich schon getauscht. Problem besteht weiterhin. Wo könnte die Ursache noch liegen? Vorhin schien die Anzeige kurz weiß zu flackern ...🤷

Hallo ich bin Peter, ich habe eine Frage, wir haben auch eine Saeco Intelia. Wir bekommen immer wieder die Meldung, Bohnenbehälter füllen obwohl der Behälter voll ist. Woran kann das liegen bzw. was kann ich tun ? Freue mich auf einen Tip. Beste Grüße

Come effettuare un riavvio per il dispositivo non vuole completare il processo di pulizia e nessuna mano per passare di nuovo all'elenco

Welchen Trick hast du in den abgebrochenen Klipp wieder zu befestigen. Leider ist er bei mir auch abgebrochen?

Weiß man was kaputt war auf der Platine?

Bei unserer macht die Pumpe Geräusche. Doch mal die Maschine die 10 Jahre auf dem Buckel hat reinigen?