No video
Saito FG-90 R3 break-in procedure.
Рет қаралды 8,259
Күн бұрынBefore I started the break-in process, I have injected 20 ml of red line oil in the crank case through the nipple located next to cylinder one!
The fuel is a mix of no ethanol gasoline and red line racing oil at 15:1 ratio.
Propeller - Fiala 24x12 wood
@budm6368 10 ай бұрын
Hi I had the same engine for 2 years ran it rich always on Valvoline 2T oil at 20/1, 7000 rpm keep a check on the head temps with a lazer temp checker after 2 years and lots of flights in a Hanger9 Corsair my engine was not fully broken in but it never ever let me down they are great engines if you look after them
@LeVap_Aviation 10 ай бұрын
I am on 2nd gallon of fuel now. So, it's not fully broken in yet, but I love it. That thing sips the fuel! It's in my Waco biplane and I like the combo a lot!
@noahschechtel8979 Ай бұрын
great video and explanation of break in procedure!! Ijust got this engine... i fly with Redline oil... how much should I put in this breather nipple? i ony have one on the bottom.thanks!! or did you do any oil for break-in? thank you
@LeVap_Aviation Ай бұрын
@noahschechtel8979 Thank you. And yes, I have injected 20cc of the red line oil through the nipple while turning the propeller before the break-in.
@noahschechtel8979 Ай бұрын
And did you leave NIPPLE and screw in fuel tube while breaking in and then take it off after break in ?THANKS
@LeVap_Aviation Ай бұрын
@noahschechtel8979 The top nipple should always be closed like I have it in the video. The bottom nipple should always be open.
@noahschechtel8979 Ай бұрын
Yes. But I onky have a nipple on rhe bottom.
@LeVap_Aviation Ай бұрын
@@noahschechtel8979 Ok! Then don't plug it up, leave it open !
@leejaehun1756 Жыл бұрын
👍 good video~explained easily and simply. next step, high needle 6200rpm setting and low needle response setting?
@LeVap_Aviation Жыл бұрын
First thank you for your comment. And yes that is correct. I set my high speed needle to about 6000 rpm on the ground and set the low speed needle to a nice smooth transition.
@leejaehun1756 Жыл бұрын
@LeVap Aviation thanks 😊 this is best simple manual video for fg90r3 break in. 👏 👌
@LeVap_Aviation Жыл бұрын
@@leejaehun1756 Appreciate it. I tried to make it simple and easy to understand. Glad someone found it helpful. Best regards.
@castlefranck3979 3 ай бұрын
This is a factory setting or intake modification? Best regards
@leejaehun1756 Жыл бұрын
how is your max rpm? I have 6050 by MENZ 24×12wood. how many turns high needle from 3 turns.
@LeVap_Aviation Жыл бұрын
I have switched to 20:1 oil ratio after the first tank as per the manual. I opened up the high needle 3 turns and I am getting about 6400 RPM on the ground with Fiala 24x12 wood propeller. I am flying it with that setting. The engine has about 2.5 hours of run time right now.
@leejaehun1756 Жыл бұрын
@@LeVap_Aviation thanks:)
@conbonesthevoid1448 Жыл бұрын
are the jugs still cracking at the bolt holes?
@LeVap_Aviation Жыл бұрын
I am not aware of that issue.
@conbonesthevoid1448 Жыл бұрын
About six year my buddy purchased on of these we broke it in per manufacturers instructions and after a couple flight the jugs cracked at the bolt holes. He sent the motor back got a new motor and cracked in the same places. Sent that one back to and they sent him another new motor saying that was the last one they would send him. So he never ran it and sold it at the perry Georgia model aircraft swap meet.
@LeVap_Aviation Жыл бұрын
@@conbonesthevoid1448 Sorry to hear that. I don't have that problem
Morris' Mini Motors Limited
Рет қаралды 2,1 М.