Thanks for the video! Just installed Whitedome on my brand new S23U with the help of this video and it worked perfectly! Aside from the camera cutout there's no difference noticed from the regular screen!

First off, thanks for making this video. I have some notes about the installation and how it differs from the official instructions: You're also supposed to place an absorbent strip along the bottom. When placing the sticker for the top earpiece is designed to go on after you install that small grey; you refer to it as a Lego piece at the top. That way, it is perfectly aligned. When emptying the glue, I would wait 100 seconds to ensure you're getting all the LOCA (name of the glue) onto the screen. It's better to have more glue than too little. To cure the screen, you want to repeat the 60 seconds on the top, middle and bottom again. So, it should get 15 seconds at the top, middle and bottom, then 60 seconds top, middle and bottom and finally another 60 seconds.

This is my second installation of this product, months apart and always come back to your video. And i get a perfect installation, every time ! Thank you for the vid!

Awesome! Great video🙌You've the perfect installation direct for our product🤩

I missed the step where I was supposed to wait for the adhesive to go to the middle, then drop the protector. Very messy mistake. Watch every step folks! Good thing they sent 2, cuz I rewatched the video and nailed it that time. Thanks for the video!

I liked how you sped up the video when installing the stickers.

Thanks for always showing the proper way to install the Whitestone dome. Whenever i get a new phone i always check your channel for help. Thanks!

Perfect. Step by step worked perfectly! Thanks so much. Peter

Thanks for the video. Everything went quickly and perfectly.

My S23 ultra's 1 year warranty expired already and want to make sure it get's a good protection. Thank you for this video, I successfully intalled the Dome glass

Thank you, buddy! I just installed mine with your tutorial, everything went really smoothly😉

Thank you bro great video, just installed it myself messed up a little bit my table wasnt flat, and when putting down the screen the glue was moving about a little but just managed no bubbles and looks great and centered.

Followed your guide step by step, same layout everything. Worked splendidly. I had a scratch, which you could feel with your nail and S-pen and it's gone gone, not even at an angle no, it's gone. Wonderful product.

Thanks again for showing me how to do a perfect installation!😊

bought this off amazon because of your vid, CLEAR PRECISE instructions. #PERFECT 1st time round!!!!

Thank you for this video.

@Josh Ouiñonez Could you please give me a link for the wallpaper shown in the thumbnail of this video? It looks really cool.

perfect tutorial prefect job!

Amazing vid. I've been looking for a protector that is compatible with the Supcase Unicorn Beetle Pro. The Milomdoi protector with the front frame of the case lifted the glass and created air bubbles. 😩

Thanks for the video! I just installed it without any issues thanks to you!

Great content. Question I see you put your phone in the supcase unicorn beetle pro cream color. I have that case. I change my cases often. You know it's not easy taking their cases off. You have to use pressure, and every time, the screen lifts. So did Whitestone fix this problem, or will it still lift. I went through a lot of glass screen protectors with my note20 ultra. I'm a little cautious about going back to glass screen protectors. What's your honest opinion. Thank you.

Great content. Question. I had the Whitestone dome film screen protector for my s23 ultra. Love it. The only thing is scratches to easily. now every case for my s23 ultra, is supcase unicorn beetle pro, and I-Blason Armorbox, poetic spartan case. And otterbox defender pro. I saw with the supcase unicorn beetle pro, the screen didn't lift after putting it on, or taking it off. I'm gonna purchase the Whitestone dome glass screen protector, tell me honestly. After filming this video, did you have any problems with the screen protector lifting using these cases? Thank you. Looking forward to your reply.

I had to repeat because my table was not perfectly level - the glue flowed right off the top of the phone and onto the table top. Got a level, made sure table was perfectly level, and it worked better than in the video on my second attempt. I first tried a highly recommended protector without liquid adhesive and in 3 attempts, I had 3 miserable failures, my reason for trying the Come Glass which has turned out well.

Perfect instructions

Thanks for the video, it worked out perfectly on my S23 Ultra. I hade the Panzerglass protector installed but the fingeprint sensor did not work at all, let alone that you have this visible circle around the sensor. This one is working perfectly

Thanks for the review using White dome and Uniocrn Beetle pro. Now I know which tempered glass I will use.👍👏🍻

I use s23 ultra mowei installation tray installed s22 ultra whitestone dome glass on my s23 ultra and it works and well fitted

Nice i got mine on but i had to mess with it a bit as the glue wasnt going towards the bottm, anyways its on perfectly my only issue with screen protectors is on the edges dust build up and im not sure how to clean it sadge, thanks for the video!

Thank you for the video. I watched it at the same time I installed mine and it went great. Thanks!

First YT'er i've heard say "use the restroom; hot water." That's how i did my install on the s10! It was flawless. I have my dome glass waiting for tonight, just got my new phone as well! :)

I have it and I love it but I have swipe gestures on and while swiping to go back a page I realized that there was a clear film coming off and I wanna know if I can just take that screen film off cause it's peeling off worse each day

Amazing product review indeed.

How much different is feel with protector than without...Im not worried about dropping as keep it in case... I was considering not putting a screen protector on good Reddit the s23 aldred is very susceptible to micro scratches...

Love your background on the phone, where did you get it and what is it called. Cheers

The adhesive glue glue went in the s-pen slot how long will it take for me to get it out like whats the adhesive expiry ? Would appreciate the help 🙏🏼

Nice, helpful video 👍. Do you know if this screen protector is compatible w/ a standard Samsung case?

I sure wish ub pro will have cam shield for the s24u like the one from tongate case

I have been use this product and ill give ⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️...I can only said just buy it and install it

Thanks for mentioning the Spen as no one talks about it

Awesome 👌 👏 😎

Just wanted to point out that you put the sticker on the left in the wrong spot. That sticker should be used to cover the 5G antenna below the power button as the sticker for the buttons is not long enough to cover it

Has anyone used this dome screen protector with otterbox cases? I have the otterbox commuter case.

i got the spigen ez fit glass protector. I havent installed it yet. does anyone have an opinion from the spigen to the whitestone?

Installed a dome glass on my S22U about a year ago and it's still in mint condition except for some dust building up on the edges.

Hi, Does it cover the edges?

Can someone help me why I have a colorful reflection at the top of the camera and at the top edge with white backgrounds?

Hi! I want to ask does the phone holder or car holder lift the tempered glass when using it without a phone case?

love the uc pro and whitestone together

do you we need to out camera protector? seems like if i buy the ring ones or glass ones they will somehow not totally fit some cases unless they have a big cut out on cameras. even the ringke and uag got tight fit on theircamera cut outs

Dome glass is best u can put....using since note 10+,yea,be carefull when u put adhesive u dont mistake and forget to slide adhesive in center of screen, ah almost forget it is compatible with RINGKE FUSION X CASE if any need info,sya

I'm so confused on the sticker at the stop that's so supposed to be for the speaker? I don't see a speaker or a purpose for this sticker. Dudes just placing a black sticker on a black phone with no indication on whatever I'm covering up. I don't see any holes or speaker.

Oh my god. I got dust in the adhesive part both times. Is there a way to remove dust from the liquid?

Way easier than the old whitestone dome setup

Is this screen protector compatible with the uag plyo?

What about the front top speaker, will the glue block it if it spreads to the far top?

Very good!! But next time, kill or turn down the music because for me, very distracting!!

Does the corner chip off easily? Had the chipping off on my s22 ultra and I didn't drop it at all

Does the S23 ultra have a build in screen protector?

Does it work with spigen rugged armor?

My Guy installed PureGear Tempered Screen protector in less than 10 minutes,no bubbles,high def,super clear and no problems with fingerprint reader + Lifetime Warranty done by accredited MTS dealer and definitely NO air bubbles.. I know I wouldn’t be able to do it myself, I leave that finicky work for professionals,anyway my hands shake and I would Fokk it up…

For me, went about as expected. First when I tried to remove the bridge, the tube cap slipped out of my hand and bounced across my desk and landed in the puddle of adhesive. Puddle was still mostly circular so proceeded to tilt it. Went to remove the tab but it wouldn't budge, pulled a little too hard and the lego piece came off and the whole thing shook abit and I ended up with air pockets all over the place. After pushing all of those out, not enough adhesive was left behind to seal around the edges to removed the glass, cleaned everything and started over. This time I forgot to tilt the brace and dropped the glass with the adhesive at the top. Still managed to work its way to the bottom. I think due to that though is why my fingerprints barely work. Even with sensitivity turned up and redoing them, they just don't take.

How can I remove a single small droplet of glue from the ear speaker after installing this?

Do you have to use the uv light as i have misplaced mine and need to replace my screen protector?

Hi. I just instaled the whitestone dome glass protection and it works just great opposite to panzer glass that i had previous with just 1 big exeption: s pen is not working smooth like on panzer glass, i have to press realy hard on screen to have some movment. Some time i feel i just break damn s pen with force i use to see any mouvment on my screen. What im doing wrong? I appreciate any help

I'll I'd ask is just don't fast forward anything, like putting the stickers on. Just go slow and explain why. I know you did after but it was annoying. Other than that slight critique, wonderful instructions. Got it going first try, always scared to try one of these on previous phones. Totally worth it though! Thanks again for making this

What about the adhesive and taking the screen off? Does the adhesive come off easily? Or will you see some stains?

Hi Josh new sub here can you tell me the name of the background that's in the thumbnail thank you!

Can I use this with an Otter Box defender case or will it pop off like others?

This is (was?) also my go-to screen protector, but with the S23 Ultra it seems the rig provided was ill-fitted and resulted in a ton of glue running out the side due to the proctor not resting on the slider and falling directly onto the adhesive. Twice. Very discouraged as whitestone seems to be moving toward decreasing quality and providing multiple attempts to compensate (previous kits came with only 1 protector and installed with 0 issues).

I had this on s22 ultra and the fingerprint was a pain sometimes when my finger was dry.

I came here to watch how to put the screen protector, Left here as a surgeon!

What happens when u remove it later? Does the adhesive do anything to the actual screen?

Somehow my gap from the top is a little big 😂 but the one from the bottom is perfect

I've ordered one of these for a phone still in the box. Should I turn phone on and set it up first to register my fingerprint or should I install glass first. Thanks

My question is how hard is it to take of and clean when replacing the dome glass?😅 that adhesive makes me nervous

Does this fit the 23 ultra with dbrand grip case?

Why the liquid isn't dispersed in the middle to begin with is beyond me. Having to maneuver the liquid around is harder than it looks. My two attempts at an install on an S23 Ultra were disasters, and I have experience with these.

Installed the screenprotector with one hair underneath :( its near the fingerprint reader. Got to accept it

I've always wanted to try this but I get so afraid of messing it up.

I messed up mine for a bit on the top the glue did not covered

Great video, I was pondering whether to buy the screen protector or not, but this looks and seems to work flawlessly. Those are some ugly cases though lol

Is it compatable with samsung leather case?

Just installed but it will barely recognize my fingerprints. Re-registered my prints and turned on the extra sensitivity, but works terrible. Followed all instructions and tips but doesn't works for me.

The whole recording is dark! One half of the sponge is folded into the frame at the beginning. You didn't release it in the middle, that's why it didn't go to the bottom first. The cases are really badass.

I want to try these but they cost too much imo

What wallpaper is on your display?

Only problem I had was it never said to remove top sticker over speaker on the front so now it is under shield. What did I do wrong?😢

Nice job but will the finger print sensor work with it installed? I think not.

I would never put some kind of glue on my screen and this instalation method is crazy hard.

I followed step by step and it still messed up :( Why is this so hard?

After long usage, like 6 months to a year, will the screen come off easily without leaving any shatters or scratches? I tempered my S23U with an adhesive UV protector yesterday and found out that the screen might be hard to remove after I have done it 😅 I should have done some research before tempering my phone, but I already tempered it. I am curious right now...

Ordered one for my S23 Ultra and it didn't come with the pin/lifter tool, which essentially makes the entire thing useless. I tried in vain to install it because I need protection for my display, but without that tool it's extremely difficult to get it to work. I'm really disappointed considering how much I paid for this product. I'm sending it out for a refund and may consider ordering another if they refund me my money.

Jeez can i just pay someone to install this.

My top screen have some bubbles on it.. 😭

with the adhesive, is it hard to take off in the event you have to remove it? will doing so damage anything?

Im so scared the glue will get into to headphone and mic

How to buy?

Dear Josh, great video but u didn't allow the liquid to come to the centre before letting go of the top clip hence that PROBABLY explains the reason why the liquid didn't spread to the bottom quicker than it did to the top

Thanks for showing the cases, ordered the Slim one (without screenprotector) And thanks to Amazon for screwing us Europeans over (25,99 Euros is WAY more expensive than $19,99...oh well)

unbelievable this guy just missed putting that rubber weight on the screen and waiting 30 seconds. This missed step just left some bubbles!. Do not recommend this video, sorry.