For daily repair posts follow on Facebook: / mobilelabuk To find out more services and repairs we offer please contact us on Facebook =) Mobile Lab Gadgets Repair and Micro Soldering Specialists Nottingham, United Kingdom
Пікірлер: 37
@asrarhassan5 жыл бұрын
No need to put solder on MIC, it will damage it with excessive heat. Just prepare the board, preheat board with hot air station and then drop the mic with tweezers only when you see solder on the board in molten form. It will give optimal results every time. For mics that have hole on top, cover it with small piece of Kapton tape before applying hot air.
@FelipeDeRamirez7 жыл бұрын
epa!!! que buena tecnica pa... tengo una preguntica cual fue la temperatura que uso en ta estacion y la salida de aire... gracias he dañado varios micros porq me paso de calor.👍
@yunusakmetin98893 жыл бұрын
Ustacım elinize sağlık şebeke problemi olan telefonun tamır videosu cekermısın
@khiljiputter74146 жыл бұрын
Boss vary Nice Good video
@eminbaxshiyev40687 жыл бұрын
how use tempurature?
@MrSoldierpraxon7 жыл бұрын
toma tu mano abajo gran servidor por no colocar ni siquiera que temperatura usaste para sacar ese microfono y instalarlo
@davidnelsoncruz21766 жыл бұрын
Esta buena la técnica . Pero no le hace daño el aire caliente al orificio del microno? Pregunto nada más tengo esa duda
@someonesomewheresri6 жыл бұрын
how much temperature do we need to put on blower and air ? thanks in advance
@jambo388 жыл бұрын
hi thanks for the info and reply..what temp is the iron and hot air thanks
@instal.apl.aplikacije61565 жыл бұрын
220/230°
@timhorton68887 жыл бұрын
Is he reparing underwater ?
@pintail1204 жыл бұрын
:-) :-)
@jambo388 жыл бұрын
hi was going to take up micro soldering seen most of youre vids you make it look so easy which its probably not..what solder and flux do you use
@RepairOutlet8 жыл бұрын
+James Shepherd I use 0.46mm multicore solder that is 60/40 tin/lead. The flux is kingbo. The main thing you need is a good stereo microscope.
@khellil27 жыл бұрын
So you need a microscope to do that? Ha! Noob!
@Hiteshprajapati204957 жыл бұрын
red mi 2 prime ka mic + &,- ka point dikhaona
@dream_world6967 жыл бұрын
check this video
@miguelalbertoalfaro52847 жыл бұрын
Te faltó lo más importante Probarlo
@sohailgabol99166 жыл бұрын
what is this is that water
@vvr0n46 жыл бұрын
luckey friends this is a alcohol to clean
@user-ih9qm1zo5k6 жыл бұрын
threw in the flux in the tops. on the membrane got a flux
@ArvindKumar-ze1hx7 жыл бұрын
samsung S3 display lite nahi aa rahi hai
@gektornadiir40105 жыл бұрын
Чувачек, еще в камере микрофон замени (тебя не слышно)! :)
@ItsameDesire7 жыл бұрын
Too bad none of those videos shows the proof that mic works after soldering.
@khellil27 жыл бұрын
Hello, you're dumbق.
@ItsameDesire7 жыл бұрын
Hi, thank you.
@khellil27 жыл бұрын
Guguru Purasu You're welcome.
@fyzullam54015 жыл бұрын
Ur right.. this man just practice Ha good work continues
@fyzullam54015 жыл бұрын
Good work continue
@dream_world6967 жыл бұрын
you r. too much paste apply in mic and paste use minor paste only touch