SAVE $1400 BY FIXING YOUR HEADLINER YOURSELF PORSCHE 981 Replacing Porsche Headliner Tutorial Guide

Рет қаралды 11,110

Күн бұрын

Join me in the garage as I replace the falling headliner in my Porsche 981 Cayman S, this is a step by step tutorial!
#Porsche #981 #headliner #diy #porsche981 #porschecayman #porsche911
00:00 Intro
00:28 Headliner is Falling and Delaminating
01:15 Tools needed to Remove the Headliner
01:57 How to Remove the Headliner
03:24 Removing the Headliner
06:07 Common Errors/Broken Parts
07:13 Removing OEM Fabric and Foam
09:15 Fixing Broken Clips
11:27 How to Apply New Fabric
15:30 How to Make Relief Cuts
16:48 How to Glue the Edges
19:31 Mocked Up before Install
19:57 Installing the Headliner in the Car
22:08 The Finished Product
Want to buy the same Headliner Fabric?
www.amazon.com...
Follow the datsun build on instagram at:
/ sinful_280z
Join me in the garage today as I remove the old, falling, sagging, and delaminating headliner from my Porsche 981!
This job has a lot of steps but it all starts with removing the plastic panels from the interior of the car. First we'll need to remove the sun visors, the dome light, and then after that you'll need to detach the A-pillar plastics and C-pillar plastics. After that the headliner should only be held up by some clips and velcro.
once the headliner is out out of the Porsche Cayman S, you can strip it of it's fabric and rub off all the old foam with a wire brush. After the surface is totally clean, it's time to reinstall some fabric.
Use 3M headliner adhesive spray when applying the headliner. It's pretty simple, in theory, to apply new headliner fabric but in practice it's a little more difficult. It's a lot of trail and error and you just have to have a feel for it. Once the fabric is attached on the exposed side, you'll need to flip over the headliner and trim the excess. After trimming, make relief cuts all around and get ready to apply more glue with a paint brush.
After everything is all dried up and stuck on, put it back on the car and admire your work.
let me know what you think of this tutorial in the comments!

Пікірлер: 83

@JordanPayneLV Жыл бұрын

8 Month Update - The 3M Headliner Glue has begun to fail in the hot 125 Degree days of summer. It's still holding on but patches of it have begun detaching. I'd suggest researching a different glue if you plan to do this repair.

@moea8579 Жыл бұрын

I'm doing research to do this exact job. A lot of advice I'm getting says that you have to spray the fabric on the foam side as well as the headliner, otherwise it's liable to peel away. Some folks also say if 3M for headliner (I think 70 or 77?) doesn't work, you can try 3M 90. Less forgiving but stronger for more heat. In case you decide to try doing this job again. Thanks for the video regardless, I'll reference it when I attempt it on my car soon.

@matshagstrom9839 4 ай бұрын

Thanks for the update

@attilam7007 3 ай бұрын

A lot of shops use DAP Weldwood Contact Adhesive Top & Trim HHR Solvent Type Spray Grade which needs to be sprayed with an air sprayer.

@toddadale 16 күн бұрын

Thank you! You just saved me $700. Very kind of you to take the time to make this video

@JordanPayneLV 13 күн бұрын

Of course, glad it helped! :)

@robertmitchell9274 14 күн бұрын

Thank you very much for this video, redid my 2007 Cayman S headliner with the help of your video. Much appreciated!

@JordanPayneLV 13 күн бұрын

Glad it helped! Good job 👌🏻💪🏻

@MiamiMiles Жыл бұрын

Had this problem in my GT4... Crazy how it happens on the 981 generation cars in the heat. Amazing vid my bro!

@JordanPayneLV Жыл бұрын

Right? You’d think Porsche would have that figured out by now, thank you man 🙏🏻🙏🏻🙏🏻

@spat726 11 ай бұрын

Mine just dropped, who did your repair, Im in Boca

@Not-A-PDK Жыл бұрын

Thanks for making this video. Was good to see the “no window removal” method in action before trying it myself. Got mine out the same way you did. I did order an oem replacement headliner (which will probably fail too🤭), but plan to practice the material replacement on the old one. Did learn that I swear and talk to myself too much while doing these jobs to ever make a KZfaq video lol. The 981 content has been great. Keep up the great work.

@JordanPayneLV Жыл бұрын

Happy to help, oh trust me there was plenty of swearing on my side too :) lol 😂

@samyb2834 Жыл бұрын

I had to remove the windows. I couldn't get it out without. Mine is a PDK, probably the reason.

@JordanPayneLV Жыл бұрын

@@samyb2834 yeah maybe the shifter is a little taller in the PDK?

@Maximchiz Жыл бұрын

Did mine same way, and I have pdk. Definitely a tight fit but follow the exact same way he does it and it worked!

@jayymac 6 ай бұрын

Glad to see and hear this. I replaced my first failed one with a junkyard GT4 Alcantara headliner, which has also started to fail. I used the window removal method and it stressed me out. I also read that doing the “taco” method can cause permanent damage to the new or recovered headliner. Although the video is cut and edited while getting the headliner in and out, it seems like you were able to get it both ways without having to fold it? I had my original liner recovered in a microsuede along with my A pillars by and automotive upholstery shop at the same time I got the GT4 liner, but now that the GT4 liner is failing, it’s time to do this job again. So happy to hear of a successful non window-removing option 👍🏻👍🏻

@JUSTIZ4LL Жыл бұрын

Super job and thanks for your hard work. You're saving me a lot of money. The dealer is a joke!

@JordanPayneLV Жыл бұрын

Glad it could help!

@andresmattos7541 Жыл бұрын

appreciate your time and effort film this sir!!!

@JordanPayneLV Жыл бұрын

Thanks for watching!

@geblah187 Жыл бұрын

Thanks for this video - I needed to replace my XM antenna and this helped me drop it enough to get access without breaking :)

@JordanPayneLV Жыл бұрын

Glad it helped out! 🙌🏻

@geblah187 Жыл бұрын

@@JordanPayneLV got the headliner dropped enough in 5 mins flat ... 3 hours to goo gone/plastic scrape all the old adhesive residue off the top so I could stick the new one on... 5 mins to put it back together lol 😂😭

@haroldanderson6021 Жыл бұрын

Very helpful video. I got the #$&@ thing out with no damage to the car or me! I was originally planning on using 3M 77 adhesive but after reading the comments I'm going to do some research. Thanks for documenting the steps.

@JordanPayneLV Жыл бұрын

Glad you got yours out! Yeah I was a bit worried after I posted this about the comments but so far the headliner is still staying up nicely. We’ll see what happens in summer

@warrenlucier5796 5 ай бұрын

I have a 2010 Cayman S and reside in Florida and had the headliner delaminate when hurricane Michael went by in 2018. This happened overnight, due to the barometric swing, and I'm lucky to have got that much time before it turned into a head towel. My car is kept in an air conditioned garage and if possible on an outing I find shade for parking. It looks like the 981 has the same problem, but believe it or not getting the headliner out of the car appears to be a bit easier of a mission. The 987, both 1 & 2. have trim to remove all the way around the headliner and it didn't want to just pop off easily either. I wish I'd just had those hard foam blocks on the back of the headliner, but no, there was a hard plastic grid epoxied to it that is like sharks teeth. The headliner wasn't going to come out the door, for me anyways and those sharks teeth left a few marks on the interior soft touch paint. Needless to say I also had to get some elastomeric interior paint and redo the afflicted parts. I went through the same basic steps for prepping for the new headliner application, but did the installation a little different. So heat and humidity is the enemy due to a water based adhesive and it separates from the soft foam. I ordered some upholstery grade material for my replacement headliner and used 3M under hood adhesive to do the installation. My Cayman is black with a sand beige interior, and I figured since I own a crocodile, I'd get some cocoa brown material and install that on the headliner. Worked great and no problem for 6 years now 🤞👌👍! If your interested in the material it is sold by Rothman Associates in Miami, Florida, phone (305) 573-8300. The Item # BKPRED-LIZ Desc. Lizardo-Cocoa (L). You can get this material in different colors or you may find something else you like. Remember to just keep your head towel free 😅🤣😂.

@eddiehill1992 Жыл бұрын

Thanks for the video, I’ll just pay the shop to fix it while I golf

@JordanPayneLV Жыл бұрын

Sounds like a solid plan to me 😂

@Stellarffxi 3 ай бұрын

Very nice... Instead of brushing the last section on, I'd have just masked the black side of the fabric and still sprayed it on though...

@robertmassucci1 Жыл бұрын

well done, you should continue making videos

@JordanPayneLV Жыл бұрын

Thank you!

@andresmattos7541 Жыл бұрын

$80,000 car quality pure quality

@wnmoy 10 ай бұрын

Yep, mine too. That’s why I’m here watching. There’s a handful of other stuff; door sill and headlamps’ glass (plastic).

@martinp1544 Жыл бұрын

Looks Great!

@JordanPayneLV Жыл бұрын

Hopefully it stays up, so far so good!

@philippec6792 8 ай бұрын

Very good job !

@supercarlover848 11 күн бұрын

Have you thought about retrofitting a 718/991.2 steering wheel to your car? I did it to my 981 and it updates the interior very much imo! Cheers for the tutorial also

@JordanPayneLV 10 күн бұрын

I haven’t looked into it! Do you need a new airbag as well? I love the 718 for the drive mode dial but I don’t think that’ll work in a 981?

@supercarlover848 10 күн бұрын

@@JordanPayneLV I got mine from ebay and it came with an airbag, it was a simple swap. You can get the turn dial coded in but I bought a steering wheel without it.

@robertmassucci1 Жыл бұрын

mine's also atlas grey, best color.

@PorfirioDiaz-ru8jk Жыл бұрын

Good job

@JordanPayneLV Жыл бұрын

Thank you! It’s still holding on after all this time, hopefully it survives the summer :)

@ianwelch8201 Жыл бұрын

Good video well done,only thing that I would like to know how many tins of spray glue did you need ?

@JordanPayneLV Жыл бұрын

Thank you! About 1.25 cans, the glue is still holding up despite the Las Vegas summer heat. We’ll see if it lasts through the whole summer

@josephng8941 Жыл бұрын

FINALLY have time over the summer to do it! Ss cables going in this Thursday and headliner fix!

@JordanPayneLV Жыл бұрын

Do some research on alternative headliner glue, in the dead of the summer heat mine is finally showing some signs on weakening

@user-hx1mx3li4j 7 ай бұрын

Where can i buy new clips like those i cant find them anywhere!!! Please help if anyone knows

@alomar-12 Жыл бұрын

As someone who has worked with 3M adhesives for many years be ready to re-do the fabric as 3M starts to fail around 87 deg F. You been warned!

@JordanPayneLV Жыл бұрын

Ahhhh no don’t say that >.< Good thing it’s almost winter time

@chuckpierce3084 Жыл бұрын

Fire Stick what would be the adhesive of choice ? If not using the 3M product. Like Jordan I live in a warm region.

@kornkid8600 Жыл бұрын

What brand do you suggest? SoCal gets up to 115deg a few days a year now.

@haroldanderson6021 Жыл бұрын

3M headliner adhesive or 3M 45 photo adhesive??? They make a lot of stuff.... The Permatex headliner adhesive is good to 170 degrees I can't imagine the 3M version being less than that.

@Not-A-PDK Жыл бұрын

Thanks!

@JordanPayneLV Жыл бұрын

You bet!

@JordanPayneLV Жыл бұрын

I really appreciate the super thanks, thank you!

@dirkdutzmann9250 Жыл бұрын

Hello, you also looked at an Alfarrarivideo from "homebuilt by jeff" and were put on his list for a win. Did he choose you in the end?

@JordanPayneLV Жыл бұрын

I was put on his list?! I didn’t see that episode can you link it to me??

@dirkdutzmann9250 Жыл бұрын

@@JordanPayneLV If you do not see the vid, how can I find you at subcribers?

@JordanPayneLV Жыл бұрын

@@dirkdutzmann9250 well I just haven’t seen the video where he mentions my build. Was that in an episode?

@cameronogilvie1075 Жыл бұрын

Having the same issue with my 981. Does the contrast in the A pillars material stand out enough to go ahead and replace the material with the matching sued??

@JordanPayneLV Жыл бұрын

The contrast doesn’t bother me, I decided not to do suede on the A pillars because they get touched more often and I figured the pattern from the suede would get all messy quickly

@samyb2834 Жыл бұрын

Do you know the part number of the clips that popped off? Mine broke completely and I can't find the part number. It seems like Porsche does not sell that specific part.

@JordanPayneLV Жыл бұрын

I don’t, I’m sorry :/ - I’d look into some plastic welding or epoxy to repair your clip

@samyb2834 Жыл бұрын

@@JordanPayneLV the end of the clip broke, what a pain

@moon3173 10 ай бұрын

did you have to bend the roof piece to get out/into of the car? In another post/youtube, the instruction was to bend it, but your video doesn't show that was the case. if you could clarify, i'd appreciate thanks a lot

@JordanPayneLV 10 ай бұрын

I didn’t have to bend mine, you have to rotate the piece just right to get it out though

@rjsd7 Жыл бұрын

what happens if I don't have the clips?

@JordanPayneLV Жыл бұрын

The ones attached to the headliner? The “ball and socket” ones? Well it would probably still stick up there using that high quality Velcro stuff they have in there, but it might fall down over time

@rjsd7 Жыл бұрын

@@JordanPayneLV interestingly, my car only had 1 from factory, it was on the passenger side

@JordanPayneLV Жыл бұрын

@@rjsd7 that is surprising, but yeah that hard plastic Velcro they use is super strong

@rjsd7 Жыл бұрын

@@JordanPayneLV so annoyed at Porsche for failing at headliner design/materials

@samyb2834 Жыл бұрын

@@rjsd7 Did you find a way to buy it? Mine broke.