Saving an Old Road Grader from an EARLY Grave ~ Caterpillar Motor Grader Sat Abandoned for 10+ Years

Рет қаралды 938,158

Күн бұрын

It is time to get the third machine that we are rescuing from the old farm! I really want to get this thing back to the Salvage Cave and work on it there, so let's bring it on home!
This machine is a Cat No 12 Motor Grader that was built in 1965. It has been parked in the same spot for a little over 10 years. It quit working one day while the family was using it, and they never got it up and running again. I plan to do some work on it to get it up and running once it's back to my shop.
This machine should be a LOT of fun!
~
Thanks as always for watching and following along with all my crazy adventures here on Salvage Workshop, I TRULY appreciate it!
Please enjoy! I know I did!
~
0:00 - Video introduction
1:00 - The motor grader
1:35 - The story of the motor grader
1:50 - Walk around and description of machine
7:19 - Putting air in the tires
11:19 - Inside of the machine and controls
13:20 - Greasing the front wheel spindles
13:45 - Bringing in and lining up the truck and trailer
15:40 - Pulling the motor grader onto the trailer
27:45 - On the trailer and off to the Salvage Cave
30:50 - Driving home
31:45 - It has arrived
32:00 - Unloading the motor grader
42:18 - Another walk around of the machine and the plans to fix it
54:00 - Conclusion and upcoming plans
~
f you have any suggestions, questions, or comments, please leave them below! Thanks for stopping by, I truly appreciate your support!
#MovingDay #MotorGrader #SalvageWorkshop

Пікірлер: 986

@nevillemills9517 Жыл бұрын

My father operated one of these back in the 1970's/ 80's on the local shire council in Victoria/ Australia. When he retired in 1988 I drove it for a short time until it was sold at that time I was 27 years old. I have driven many graders since 1992 full time and built many roads and maintenance grading roads. I am 62 years now and retired. I still miss it but had a great time doing what my father did. After the 12E grader was sold I spent a year on a case 580E loader then operated a 926 cat loader till 1992 loading trucks in our gravel pitts within our shire. I had some wonderful times and got many memories. Cheers from Nev Victoria Australia.🤠👍

@ironman3406 Жыл бұрын

I love old Cat graders, I’ve got a 1955 212 and a 1956 12 myself. There are two blade lift controls on the main gear box, one controls each side of the blade independently so you can manage blade angle. The side shift on the main gearbox will move the whole DCM (drawbar circle moldboard) left and right allowing you to get the whole blade positioned further out from the main frame to pull slopes as an example. The hyd blade shift with the control closer to the window will move just the moldboard left and right. The control on the very far right of the control box is your throttle control, and the little foot control is deceleration. So you could set your desired engine speed and then decel as needed without having to always use the throttle lever. That additional drive shaft on the front; you are right would have been to control a front mounted attachment of some kind. Blades are fun and not as complicated as folks make them out to be. Look forward to seeing it in action again

@somerandomguy3868 Жыл бұрын

It's refreshing to see someone do their thing without any BS, never easy moving a piece of equipment that's not running

@tool717 Жыл бұрын

Machine time is the best time .... Rollin Rollin

@Bris650 Жыл бұрын

Matt, really enjoy your video's. Love to see you working together with your dad!! I really like it that you keep it clean and not silly as others I've seen. I can see the passion you have for getting old gear functioning again. Keep up the great work and we'll keep watching😁

@terryrogers1025 Жыл бұрын

Nice recovery job young man, one of the better I have witnessed. Looking forward to this series. Thanks for the ride along sir. You have yourself a good machine as far as I am concerned.

@joelhebert4559 Жыл бұрын

Stumbled onto this YT video and don't know why, but found it fascinating. Great to see a father/son team working together!

@stevesalvage1089 Жыл бұрын

Another great find ! Can't wait for the engine investigation, let's hope the bores are salvageable! Great filming Matt !

@giggiddy Жыл бұрын

Your style, simplicity and common sense approach has put you at the top of my KZfaq list. Great, clear and concise video with no stupid gimmicks. The last guy I used to follow bragged about how cheap he was and half-assed patched his stuff back together even when being cheap made them dangerous. You save where you can but don't mind digging in your pocket when necessary. One request- when you place a subtitle explaining something, can you leave it up a few more seconds as some of us read slower than others. Thank you sir and keep up the great work!

@stevejette2329 Жыл бұрын

D - 1st time here. Being frugal is one thing. Being unsafe while saving money might be something else. Using 2x4s instead of a legit jackstand ? Using an old, underpowered jack to lift something big, knowing ahead that it was large equipment ? hmm 1st impression as I am only 10 minutes in.

@M.TTT. Жыл бұрын

it can be fun to make old stuff work with what ya got and is more realistic in some ways (farmers), but then later on fix them properly.

@M.TTT. Жыл бұрын

@@stevejette2329 lol good point, but we've all been unprepared at some point in our lives. A good 20ton+ bottle jack and he's good to go. Using old peices of 6x6 or railroad ties for jack stands is fine too if you use enough.

@M.TTT. Жыл бұрын

@@robertmiddleton1227 but did it work though? Yes

@stevejette2329 Жыл бұрын

@@robertmiddleton1227 Wow. A road "greater" ??? It's 'grader', as in a 'grade' meaning a level. It's right in the title. "you shouldn't never brought ..." should not never ... ? That may be the only trailer he has. wow

@timofeyserikof8397 Жыл бұрын

With each new release, you set new tasks for yourself, and the further you go, the more difficult these tasks are! I love graders since childhood, I will be happy to watch how you bring this monster back to life!

@neil6212 Жыл бұрын

ANOTHER great find! I love the way you approach every machine logically, and carry through! Looks like you're needing a bushel of fittings and a mile of hose! The conditions of the old hoses is typical of the commonly found rubber lines with steel braid. It might require a King's ransom, but the stainless braid with the Teflon inner could be a great answer. We used a lot of them for high pressure lines on machinery in production. When I retired, some were still in use that I made up 20 years previously.

@brianjennings3172 Жыл бұрын

Man, can't wait for you to dig into this one! I've always had a thing for road (motor) graders and can't wait to see how this one goes.

@gordonagent7037 Жыл бұрын

Great score, it’s so nice to see a guy who loves old iron get a great find like this, can’t wait to see this project start

@alfiversen7023 Жыл бұрын

An epic series awaits, no doubt! Unless you have a mile long driveway you probably do not NEED this machine, but then again what a great way to stack up future content. A few tense moments loading that thing made for a great breakfast thriller for me- so thank you Mat. Looking forward to the engine rescue.

@The-Deadbolt-Deputy Жыл бұрын

That hydraulic winch and the snatch blocks was perfect for getting this ole girl loaded

@bombardier3qtrlbpsi Жыл бұрын

Always a great video when you can work on a project with your dad. Thanks for sharing 👍

@michaelalan1546 Жыл бұрын

Oh man, love it bro I’m a blade guy myself, been operating one for about 20 years and I love the old cat machines! Look forward to seeing you restore this machine and putting it back to work!

@jakejohnson5702 Жыл бұрын

I love your videos, I think you are great at what you do, and it is great how you can salvage such run down machines in the weeds like you do.

@r.w.felton6020 Жыл бұрын

It looks better than the one I operated on road and site prep jobs back in the 1980's. Great machine for rough country dirt work. Thanks for the video it brought back lots of memories pleasant and otherwise.

@normhowes2975 Жыл бұрын

As my Dad ran a grader, a 64 Galion, for 20 yrs these things hold a spot in my heart. Thank You for at least saving it from the scrap man at least for now.

@alanjarvis8777 Жыл бұрын

Good job in all the videos, you are getting steadily better at recovering these old beauties! Look forward to seeing the next stage!

@pinetree9343 Жыл бұрын

Excellent find! If more people restored equipment like you, we'd be a more resourceful country.

@michaelguinn5736 Жыл бұрын

I really like seeing some of this vintage equipment saved, the scrap man could care less...be safe!! God Bless!!!

@bonniedugle1763 Жыл бұрын

My Dad drove one of these for a living. What an adventure this was. I'll have to subscribe and watch you fix it. Thanks for the memories.

@brianelliot2719 Жыл бұрын

Looks like a very interesting project, looking forward to its restoration. Thanks for the video - excellent photography as usual and you tell a great story.

@davidakridge2831 Жыл бұрын

Simply wonderful videos. You and Matt from Diesel Creek are all I need these days. No more TV. Just wait on my video to appear. That utility truck is turning out to be an amazing rescue vehicle. After you get it running like a top again, might I suggest a good power washing and some Salvage Workshop logos on the side. Need to dress her up a little. Thank you for such awesome content.

@chuckhaynes6458 Жыл бұрын

That's an excellent machine. Caterpillar 12 motorgraders were the standard of the industry for decades. Very good condition and certainly worth the engine work that will be necessary to make it functional again. I've used them many times and they are the top of the line. With the addition of the front blade this machine is good for plowing fairly deep snow. I would set the front blade about 10-12" above the road and the main blade on an angle at road surface. I'm looking forward to watching you do this one up right.

@davec.4726 Жыл бұрын

A brilliant video now I can't wait for the next one, it amazes me how much effort you guys put into your work I was out of puff just looking at the way you had to man handle the loading ramps on and off the vehicle, thanks for sharing that with us and all the best and cheers from across the pond.

@billarcher Жыл бұрын

The lean wheel control is used to lean the wheels into the draught of the blade to reduce the effort in steering the grader while pushing and cutting dirt. The mechanical side shift is used for small shifts of the blade but if the machine is fitted with a hydraulic side shift the mechanical shift is almost never used. When using the mechanical controls, grasp the knobs firmly and push them into engagement hard. Don't ease them in because they will kick hard because the dog clutches in the control box will be worn particularly on the blade lift. You have quite an experience ahead of you learning to operate this machine. There are cheek plates missing from each end of the mouldboard. These are used when cutting drains and are a cutting edge as well.

@brucemullen3889 Жыл бұрын

Those old knuckle buster blade are what I ran many years ago. Make my hands ache looking at them .

@billarcher Жыл бұрын

@@brucemullen3889 Some were worse than others depending on how worn they were. I haven't been on one since about 1974. You learn quickly to keep a firm grip on the lever and slam it in instead of trying to ease it into engagement. When the dogs are very badly worn it's impossible to get them to engage if there is a lot of weight on the blade. nevertheless, they did a lot of work and would keep going when most of the opposition machines had stopped.

@ronhaworth5471 Жыл бұрын

Exactly!

@willford9205 Жыл бұрын

If the gear lash is setup right, they dont kick till they wear. I had thr pleasure of running one before and after a overhaul..night & day diffence. NOT that when setup right. I used EVERY lever all the time. DAMN! I'm old

@billarcher Жыл бұрын

@@willford9205 The graders that I was operating were well worn and the owners were reluctant to spend any more money than necessary. I did operate a new one for a short time and that was really nice to use. I also operated G and H series machines for a while and liked them better. I am getting old as well and would rather watch other people operate them now.

@Dave-1277 Жыл бұрын

Running against Vice Grip Garage and Diesel Creek, this has to be one of my all time favorite KZfaq channels out there! So inspiring and awesome! Nice job as always brother, brings a smile to our faces when we see you upload another video! Keep up the good work!

@TheTomcory Жыл бұрын

Junk Yard Digs is a good one. Check out Grumpy Farmer.

@TheTomcory Жыл бұрын

But this is my #1 show I watch.

@davidakridge2831 Жыл бұрын

LOL!! I just mentioned Diesel Creek in my comment before I saw yours. Now I have to go check out Vice Grip Garage.

@4acrehome168 Жыл бұрын

@@davidakridge2831 you never saw VGG? Oh man, I wish I could experience him all over again 🤣

@TheTomcory Жыл бұрын

@@4acrehome168 I'll check it out

@tedohio3038 Жыл бұрын

Nice video, your dad is a good operator. Think I would drain the fluids now.

@Justin-pb3lt Жыл бұрын

I love it,one of my older half brothers used to drive a grader for the county & grade the dirt roads & clean up the ditches,he would drive a old one like that one or the ones with the square cabs

@xtender5 Жыл бұрын

Had a blast watching Matt from Diesel Creek wrestle with his Galion from a similar era. But his is, apparently, haunted. I hope your Cat gives you more love than his Christine has.

@justinbarker4603 Жыл бұрын

Christine tried to take Matt out when he was unloading

@sallybrokaw6124 Жыл бұрын

Galion,Ohio. I live 15 miles south and used to work there for a snowplow manufacturer.

@xtender5 Жыл бұрын

@@sallybrokaw6124 Ah, sorry for misspelling. 😁

@xtender5 Жыл бұрын

@@scroungasworkshop4663 I heard that Australians have good taste. More proof.

@PaulBarwick Жыл бұрын

I was just thinking of Matt and Christine. :)

@patrickcolahan7499 Жыл бұрын

If it were me, especially since you don't plan to work on it in the near future, I would drain the oil fill the cylinders and case with diesel and let it soak until you are ready to do anything. Great find, and I do believe it will run. Thanks for sharing.

@SalvageWorkshop Жыл бұрын

Patrick, I think that's a GREAT idea!... I should probably add an exhaust flapper in case the bungee cord breaks and the coffee can flies off!

@bigmotter001 Жыл бұрын

Matt, don't change your style of videos. You have and will continue to climb the ranks of KZfaq! Thanks for all of your postings and take care!

@pinetree9343 Жыл бұрын

Beautifully executed rescue. Thanks dad!

@freethought2296 Жыл бұрын

When I started watching you, you worked outside on an old steel work table and restored old rusty tools and gadgets. You've come a long way, my friend, and you've earned it every step of the way. Keep making great videos, and I'll see you on the next one. The scenery is pretty; what part of the country are you filming from?

@craigsowers8456 Жыл бұрын

Couple of tips on the loading process: ~ 4ft Oak 2x6" placed between the tandem axles and at the foot of the front tire leaned towards the rear will lock them up better than chocks; the forward tire will try to roll back and up the board but won't be able to due to angle (and sturdy Oak won't break). ~ having a couple of "Come alongs" would have helped to lock the steering straight and lifted the blade more so it could be chained up in a higher position; there's a few more inches left in the cylinder's travel. Alternatively, a thin 1" board inserted into the trailer to blade gap would allow it to "Slide" over. ~ Your "Winch Cable" appears to actually be "Wire Rope" (anything larger than 3/8th's inch is "wire rope") and you need to have a "Safety Blanket" over it as it will literally cut you in half if she snaps ... just looking out for your safety Bro. ~ You figured out putting a snatch block doubles pulling power. All in all, congrats on a successful recovery and looking forward to more progress on this one !!!

@dansbrown1313 Жыл бұрын

Great advice Craig, us old folks, have to help the young ones when we can.

@electricboatal 2 күн бұрын

Nice find. You will be able to get it up and working without too much trouble. I had a Cat 12 exactly like that many years ago. I used it in my grading business and it was a great money maker. I had contracts with the county to maintain a number of back roads and in the winter I pushed snow removal quite a lot. I lived at 6500 feet so we got a fair amount of the white stuff. You called it right about the controls. The aftermarket blade curl is a nice improvement over loosing all of those bolts and rolling it one way or another. I later bought a much newer Cat 12 and it was like driving a new Cadillac compared to the old knuckle breaker controls. I would fix it and make money with it for a while and sell it. Plenty of people still use the old Cat’s.

@davidcoudriet8439 Жыл бұрын

Congratulations Cat Grader; you got your second chance! Thanks for saving it.

@dandunlap8638 Жыл бұрын

Been waiting for you to drop another video

@Yackhammer75 Жыл бұрын

A bottle jack and a small portable air tank(to provide a large initial volume of air) might be some really inexpensive additions to the recovery truck.

@darrenhawken9766 Жыл бұрын

Great machine , you will not be beaten , well done look forward to see you get this sorted, thanks for sharing 👍

@craigknoblock3235 Жыл бұрын

Nice project! Looking forward to seeing it put to work.

@raymondhill3446 Жыл бұрын

What a fantastic old machine! I love this old blade! Can't help but wonder if you would have been better off loading it backwards to keep the weight forward? Food for thought 🤔 Not telling you how to do it by any means! Great video as always 👍 Take care and stay safe!

@SalvageWorkshop Жыл бұрын

I would have LOVED to load it backwards, but I wasn't sure how easy it was going to roll, and in this direction we had gravity helping us out... It sure did roll well! Good Thought Raymond, and thanks for watching!

@jfarlooker5614 Жыл бұрын

Good call. It should be reversed for proper weight distribution .Hauled dozens over the years.

@stevejette2329 Жыл бұрын

Ray - Yes, I wondered that. Front first allowed them to steer. Backwards they would have no way to control the front. Field improvisation.

@jamesrobinson1022 Жыл бұрын

That has to be one schetchiest loading ever. What was probably the worst is having the winch controls in the bite zone.

@jexsmx6608 Жыл бұрын

Glad to see I wasn't the only one cringing during the loading sequence. It only takes once...

@SalvageWorkshop Жыл бұрын

Yeah it was a bit sketchy! Moving the winch controls isn't an easy thing to do, but I might think abut that, we'll see!

@ericpaul4575 Жыл бұрын

The loading was sketchy, but the hauling was more so. There was like no tongue weight. All the weight was behind the trailer wheels. The back ones were so overloaded they probably lost half their life on that trip. I am glad you made it to the shop safely.

@alwaysmatterinmotion Жыл бұрын

The unloading was worrying me too. We'd hate to lose you, Matt, or see you injured. It can take a little longer, but extra blocking, safety chains, or just walking the long way around the machine could save your life if something slipped or broke. That steel is completely unforgiving; stay safe.

@tomekfixes Жыл бұрын

Yeah I was wondering... Wouldn't be easier and much safer to load it backwards? Better weight distribution also.

@johnvaluk1401 Жыл бұрын

Looking forward to more of the grader rescue. Nice. Thanks again

@ronhaworth5471 Жыл бұрын

I remember seeing them back in the early 60s. Real workhorse!!

@bobw7066 Жыл бұрын

I have been in the earthmoving trade for almost sixty years and that the person who fitted the rear tyres did not have a clue, because grader rear wheels are chain driven there is no power divider between the wheels on each side, the tyres must be matched in diameter on the same side resulting in the chains inside the box fighting each other by one wheel trying to go further than the other because of the different diameter. Looking at your grader both of the leading front tyres appear to be much newer than the rear ones, put the newer ones on one side and the worn ones on the other side bearing in mind to keep the wheel diameter as close as you can on each side . From Australia

@SalvageWorkshop Жыл бұрын

Good to know Bob! That totally makes sense, and wouldn't be too hard to do! Thanks for letting me know, I appreciate that!

@jimrankin2583 Жыл бұрын

Actually all 4 drives on the old CAT graders are coupled rigidly together. There’s no differential in the center of the axle. That and the fact that they’ve got the majority of their weight over the drives is why they’ll pull through most anything without spinning out. So if you can get all 4 rear tires as nearly the same diameter that would be best. In dirt it doesn’t matter all that much.

@jamesgibson5876 Жыл бұрын

Yes it's like 4x4 .. the wheel diameters have to be equal or the tires will just fight eahoter and have to scrub to even turn

@andypi68 Жыл бұрын

Hey, you are amazing! Just one question: what about the OLD RED???

@RustyNail5856 Жыл бұрын

First of all I'm glad to see that you and dad working together, when you look back you will back at the fun times yall had together. i say this because i did not spend a lot of time at the end with my dad i now i wish i had, you think that you have more time , and then something happen that you don;t., and i miss him . i wish he was still here . i am glad to see that you got the big boy home. and that has a lot of extras on it , that is a very nice machine that you found there. i wish i cloud find some heavy equipment here in FL. i don't know how you do it. i would love to found one and fix it. that would be great. i would love it. great video, keep up the good videos and i will see you on the next one. take care.

@joetrippi1603 Жыл бұрын

Glad you got this one home to be able to work on it there

@josephkrug8579 Жыл бұрын

I love these videos...if you keep finding such large toys, you will need to soon find a bigger trailer to go with it :) And I doubt it would work well, but do you have a big enough compressor to blow air in one end of the frame to force the wasps and nest out the other end or out all the holes? Or maybe run a working large motor exhaust through a pipe that then fed through the frame for pressure.

@SalvageWorkshop Жыл бұрын

Lol... I'm already looking for a large Low Boy trailer and semi tractor to move all my big toys!

@yezok01 Жыл бұрын

I think it would have been much easier loading the grader the other way round. You have the heavy end hanging way past the axle which is safety issue putting a lifting force on the truck rear axle good thing highway traffic control never spotted you you would have been paying fines until eternity. The way you loaded was and is very dangerous!! If you would have gotten any sway at speed you and anyone close to you tow unit would probably be DEAD !!! Think before you do this stuff

@australiantruckspotting8883 Жыл бұрын

That’s a lovely old grader, definitely too good for scrap.

@Chad93oleblue Жыл бұрын

That dang winch has some TORQUE! When you hooked on the blade everything was stretching..the chain,the j hooks,the blade,the trailer everything was screaming for relief!

@keithmatthews1673 Жыл бұрын

As soon as the trailer arrived, half the viewers were shouting at the screen - its not big enough! Nice machine though the water ingress into the motor might prove tricky - but it will be interesting 😃

@SalvageWorkshop Жыл бұрын

And somehow it FIT!! I measured it before I went to get it!

@jimrankin2583 Жыл бұрын

I did the same thing with a 212 on a 24’ single wheel triple axle gooseneck trailer. I knew I had to load it back first to get the weight distributed correctly. Problem was it was parked so that was winching it uphill onto the trailer. Steep uphill. Hand winches…..Hot summer……afternoon sun……..no wind……South Georgia! I made it 4 hours drive home without incident though.

@dale5898 Жыл бұрын

Hi Mr. Salvage, I think your son is a machine. I thought maybe he was born in a foundry. With the two of you there is a lot of knowledge. Thank you guys for your hard work.

@bensymington5550 Жыл бұрын

You’ll get it running it’ll be a good piece of equipment for your farm

@rcamsc67 Жыл бұрын

I recently bought a backhoe that had been sitting outside with the exhaust pipe uncovered for 12-13 years with rain going straight in the engine. Had it running in 30 minutes. Gave it some fresh fuel, primed it up, new battery and engine runs great.

@scottgm321 Жыл бұрын

Big shout out to dad for all his help. May have to title this episode “The longest Yard.” Lol. An extra chain would have been handy to secure it while you backed off the winch to reposition. Glad everyone is safe.

@tomswindler64 Жыл бұрын

Your commitment to getting the job done is always impressive as hell.for a one man band you accomplish so much.having your dad help out on this one was what you needed.do you have people that interested in buying some of the machinery,or you just use it for your business. Great video as always 😎😎😎👍👍👍

@michelecrown2426 Жыл бұрын

Well, other than thinking you were crazy for loading that beast on that trailer, great save. I hope since you worked so hard to rescue it from what could have been it’s grave, it will treat you well on restoring it.

@davesvintageequipment5319 Жыл бұрын

Enjoy finding a new channel that loves old equipment as much as i do. I hope to see more of this critter in the future.

@bow-tiedengineer4453 Жыл бұрын

One of the other machine revial type channels I watch, Diesel creek, just did a video showing off his grader and trying out a different style, and it reminded my a bit of your videos. Now you get a grader. An amusing coincidence. Nice to see you saving more old iron.

@oddtechman Жыл бұрын

You sure have a challenge there Matt!!!! If it goes anything like what Matt, over at Diesel Creek, had with his Gallion grader "Christine".. we are in for a real treat lol. Thanks as always for sharing

@spikeharvey6464 Жыл бұрын

that is awesome i live not far from Decatur and actually work at an old asphalt company in Decatur that still runs a no.12 grader!

@pullimgsm Жыл бұрын

That is the same model grader my dad delivered to Watertown NY in the 60s. He drove it from Syracuse to Watertown. No truck was available. My brother and I took turns riding with him. Good memories.

@dustoff1472 Жыл бұрын

Congrats, you got a grader. Enjoying the channel. Tks for sharing.

@rwagjr Жыл бұрын

Awesome to see the appearance of 'Papa Salvage' on this video! You probably never imagined how much joy & inspiration your vids bring to people all around the world! I appreciate your work ethic & always positive attitude. Blessing to you & your family from Jerusalem. ב"הש

@t.l.robinson2162 Жыл бұрын

I happened upon your channel by accident. I am very glad that I did. You have very good content. I look forward to seeing the grader start and operate.

@frankeberhart265 Жыл бұрын

Great video! Looking for to seeing this big beauty roll again!

@milwsdl39 Жыл бұрын

Thanks!

@milwsdl39 Жыл бұрын

Awesome job another piece of history saved just think no DEF fluid

@garyfeltus9801 Жыл бұрын

Great old grader looks good for it's age. Hopefully the motor isn't going to be to bad. I believe you right on the injection pump. Lots of hoses to replace. I really hope you can get it running. Heck there might be another motor you could find. Great video.

@somerandomguy3868 Жыл бұрын

Looking forward to seeing what you do with this old pan

@phillipdickinson8557 Жыл бұрын

Matt I have watched you from back before big red and the scrap yard and rebuilding anvils and old tools made these three pieces of equipment your best videos yet and I can't wait for your next videos I have enjoyed them all.

@michellebryant5811 Жыл бұрын

Well done lads. That grader has fought you every inch of the way

@Sheddtycoon Жыл бұрын

Will love to see you get to working on the old Grader. Take care my friend.

@gregorythomas333 Жыл бұрын

My most favorite toy when I was a kid was my big Tonka Road Grader...it was huge...at least to a 5-6 year old :)

@SalvageWorkshop Жыл бұрын

I had the same toy and loved it just as much!

@CV-uy1jc Жыл бұрын

Great Video! Really looking forward to watching the restoration on this baby! I sure hope the engine is salvageable and doesn’t hold you back.

@petrhoward Жыл бұрын

Effective way of destroying wasps. 5 gallons of gasolene and a match. I worked on these graders when they were new! - Blade lift left and blade lift Right - one blade 2 controls.

@thomaschandler8036 10 ай бұрын

Nice old machine, love your videos. Keep up the good work.

@needaccount9597 Жыл бұрын

I have memories, you have learning to do. Those blade lift levers are a great idea.

@MrGeroth Жыл бұрын

Boy I can’t wait to see you get this running.

@primitiveman8150 Жыл бұрын

I still operate one of them today. The 12 e. Great old graders. The big problem is greasing seems to take all day. They opened up most of Australia in the early days.

@GiantRiderRob Жыл бұрын

Whoa just popped in after finishing an old vid and BANG! Road Grader time! WOOT!

@SalvageWorkshop Жыл бұрын

Thanks for stopping in Rob!

@horstszibulski19 Жыл бұрын

Wow what a job to get that thing onto the trailer, but the winch in your truck is a real beast! Thx for showing! 👍👍👍

@prophet1782 Жыл бұрын

Good to see. Hope you get it fixed and running. Good Luck.

@97-20-media Жыл бұрын

Good to see the motor grader at it's new home

@davidbohner692 Жыл бұрын

Another gem in the rough 👍🏻👍🏻👍🏻👍🏻👍🏻👏🏻👏🏻👏🏻👏🏻👏🏻⭐️⭐️⭐️⭐️⭐️✅✅✅✅✅

@Makete100 Жыл бұрын

You and your dad are amazing. Another great video.

@delwhylie4748 Жыл бұрын

Nice work loading and unloading, that truck has an impressive winch. Hope to see that grader running soon...

@bennyogden4524 Жыл бұрын

I have to admit man you work your ass off for everything you get man keep up the good work

@duginvirginia5737 Жыл бұрын

Looking forward to the future on this series. The lever that's above the parking brake, I believe, is the PTO engagement for those shafts that run to the front of the grader. It would have had a snowplow assembly on the front and those additional driveshafts would have operated the associated equipment / attachments.

@jimrankin2583 Жыл бұрын

Yes, it’s a shift to allow the use of the scarifier lift shaft to run a lift to raise and lower the snowplow when it and it’s lift box are fitted.

@douglasrdeaton Жыл бұрын

Awesome that's a great find.

@joeyjeny7725 Жыл бұрын

Find watching your videos very relaxing I wish I had the knowledge about agriculture machinery like you do, truly astonishing the project I've seen you get running well done and I will forever watch your channel god bless 🙌

@justina249 Жыл бұрын

Nice to see a cameo by the Chalmers loader. Sounds like the old girl is still doing well. Hope we can give the old Cat another shot at living.

@michaelb.5345 Жыл бұрын

Very smart work. Great video

@mdouglaswray Жыл бұрын

NICE grader!!! That big CAT motor will likely come back to life!

@b.abrackus6403 Жыл бұрын

I wouldn't put much money into this grader if l was doing it....they are a tough sell... trust me, l owned several very similar Cat graders. I do enjoy your videos very much 👍