Schluter®-Systems-No Access Plumbing Demonstration with KERDI-LINE

No video

Schluter®-Systems-No Access Plumbing Demonstration with KERDI-LINE

Рет қаралды 156,085

Schluter-Systems North America / Amérique du Nord

Күн бұрын

#schluterkerdidrain #schlutershowersystems #schlutersystems
When there is no access to the plumbing from below, KERDI-LINE is installed to the appropriate height and connected to the waste line prior to the installation of the shower base. Select this video to watch how it is done.
For any questions you may have about this video and the installation of Schluter®-Systems products please call our customer service line:
Canada: 1-800-667-8746
U.S.A: 1-800-472-4588
For further information please visit our website:
www.schluter.com
Subscribe to our channel: / schlutersystems1
Facebook: / schlutersystems

Пікірлер: 19

@fishclaw901 2 жыл бұрын

If you’re using a Kerdi shower pan I’d recommend putting it on before the channel body. The metal part of it is wider than the opening in the shower pan. Great videos though, overall made the installation a breeze!

@hopkinshome3799 2 жыл бұрын

I assume your All Set product can be used for the drain as you state it has to be unmodified thin set but All Set is modified.

@schlutersystems1 2 жыл бұрын

Hi Hopkins Home! Yes, you can use ALL-SET or any of our thin-sets or an unmodified thin-set to install the KERDI-DRAIN. 🙂🍊

@artofficialbrain 2 жыл бұрын

What if you are installing Ditra heat and kerdi-line on slab with no plumbing access? And I’m using dry pack mortar for my shower base. Would I position the drain 1/4” higher than the top of the dry pack mortar? Or since I have a tileable grate, should I just thinset a strip of Ditra on the drain grate? Thank you

@schlutersystems1 2 жыл бұрын

Hi there! Sometimes it's just easier to have a proper conversation. Mind giving our Customer Service team a call to discuss your project? 800-472-4588 (US) 800-667-8746 (CA) Thanks!

@chrisjohns38 2 жыл бұрын

why is the rubber coupling used instead of a hard fit with straight pipe cut to suit?

@schlutersystems1 2 жыл бұрын

Hi Chris, the KERDI-LINE is stainless steel and most pipes they connect to are PVC or ABS, so the coupler is needed to bridge between the two different materials. Thanks!

@ST-cy6we 3 жыл бұрын

3:23 Is using Kerdi-fix to adhere the drain housing to the foam still an approved method?

@schlutersystems1 3 жыл бұрын

It sure is!

@Sugarshane88 11 ай бұрын

Where is he getting that little extra bit of pipe

@schlutersystems1 11 ай бұрын

Hi Shane! That piece of pipe is the same as the plumbing below, so you would just measure and cut a piece from what you have for the rest of the project or purchase. Hope that helps!

@ChristopherJames4 Жыл бұрын

No way he doesn’t get thinset all over his wrist / forearm when he puts the primer / cement on the trap below the subfloor.

@BenElkind 4 жыл бұрын

What happens if I have a 2" sewer drain already cut flush with the subfloor?

@schlutersystems1 4 жыл бұрын

Hi Ben, Do you mind giving our Product Support team a call? US: 800-472-4588 CA: 800-667-8746 Thanks!

@bkoz319 4 жыл бұрын

is it in concrete?

@fishclaw901 2 жыл бұрын

My plumber always glues the pipe into the p trap which he shouldn’t, I usually have to cut the floor open than cut the pipe lower and put a coupling on lower down. The it has to be glued afterwards like in this video.

@telarroja 2 жыл бұрын

Use a cutting wheel drill attachment then glue a coupling and add an extention to appropriate size

@XCBen 3 ай бұрын

This is the way