Schneider Electric ATV12 VFD, local control, commissioning and parameter set up. English

Рет қаралды 31,997

Күн бұрын

Schneider Electric ATV12 VFD, local control, commissioning and parameter se up. Forgot to demonstrate how to factory rest, but please refer to manual below page 46. All you will need is in that page. For manuals, parts and related videos please see below.
ATV12 quick start guide: download.schneider-electric.c...
ATV12 user manual: download.schneider-electric.c...
ATV12 Drive: igselectronics.co.uk/products...
Direct contact on Linked in: / ingus-sudints-1b2a2517a
Website: igselectronics.co.uk/
eBay store: www.ebay.co.uk/str/igselectro...
Run a 3 phase motor on single phase power, basics: • Run a 3 phase motor on...
Single phase to 3 phase VFD drive home setup: • Single phase to 3 phas...
Single Phase / Tree Phase Inverter 3 Wire Control Station: igselectronics.co.uk/products...
Single Phase / Tree Phase Inverter 2 Wire Control Station: igselectronics.co.uk/products...
Multi frequency control Station: igselectronics.co.uk/products...
MOP/Electronic Control Station: igselectronics.co.uk/products...

Пікірлер: 16

@IGSElectronics 3 жыл бұрын

Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.

@glennlocke8226 3 жыл бұрын

Very grateful for this video. Just little slower & clearer would be great. Your European accent is a little hard to follow. Pretty sure I have set mine up properly however I had to watch it many times. So just a bit slower with less malarkey for the non electrical engineer like me. Thanks again.

@IGSElectronics 3 жыл бұрын

Working on it, Thank you.

@unacceptableminority7101 Ай бұрын

can this drive be run on 0 - 3.3v? Eg. putting it in 0-5v mode using Al1 and com and somehow making the drive run at 100% when it reaches 3.3 and hold all the way to 5v?

@yacineevil 2 жыл бұрын

Thanks that’s helpful

@amoMiFlia Жыл бұрын

Hola me prodrias guiar en lo siguiente, ese variador esta en una talanquera de peaje, en uno muestra falla E01, E02 en otro la E13 en otro el display parpadea en FCS, y no logro encontrar como una listado de fallas o errores

@jagmohansoni4840 3 жыл бұрын

Mera yah eliminator meri mere se iske galat button dab gaye h minut Tak ke bad apne aap stopHo jaati hai please request hai aapse ki mujhe bataen ki kaise theek hogi

@pannelachandrakala4367 Жыл бұрын

sir can i give dc supply from solar to vfd....then if i give dc supply to vfd ,how can i read dc voltage and current from vfd

@user-qj1pr1vn5u 5 ай бұрын

Bang sdh saya setting HSP posisi 60 ..rpm tetap tdk naik ..mohon pencerahan nnya

@konstruction_aps 2 жыл бұрын

Fantastic video. You mentioned that you are able to set a higher HZ in the vid. I have tried that but can not get my motor to spin up past 50 Hz. I want to go to 200 Hz. Do you have any clue to why not?. Best regards Thomas

@IGSElectronics 2 жыл бұрын

HI There. There is 2 types of frequency in your drive. One is base frequency that can only be 50 or 60 and other is run hz. Change your max frequency to hat ever you need and you should be good to go, believe i mention in video what is what.