Screw Jack assembly and parts in Creo Parametric (All parts included)
Рет қаралды 69,112
Күн бұрынScrew Jack assembly design in Creo Parametric.
In this tutorial, we will design each and every part individually for the screw Jack. Then, by using the bottom-up assembly design approach, we will assemble them to complete the assembly. So let's design the Screw Jack assembly and its parts in Creo Parametric.
Timestamp:
0:00 Intro
0:53 Body
6:12 Nut
11:38 Screw Spindle
18:12 Cup
21:47 Washer
24:30 Counter-Sunk Screw
28:30 Tommy Bar
32:30 Assembly
Join this channel to get access to perks:
/ @cadxtraining
Playlist:
• Part Design in Creo Pa...
• Complex part design in...
• Sheet metal Design in ...
• Surfacing in Creo Para...
• Plastic Design in Creo...
• Assembly Design in Cre...
• Detailing the drawing ...
• Gear design in Creo Pa...
@CADxTraining #CADxTraining #CADx
/ @cadxtraining
/ cadxtraining
t.me/CADxTraining
@Kreatorzone 3 жыл бұрын
Thank you CADX , Love ur work. U have been an inspiration for me to start my own channel.
@anvith01 3 жыл бұрын
Nice
@CADxTraining 3 жыл бұрын
Good to hear. Don't demotivate yourself by any means. Keep doing and keep growing. Make quality video always.
@Kreatorzone 3 жыл бұрын
@@CADxTraining THANK YOU SIR
@harshithalshi4510 Жыл бұрын
Very good explanation and teaching, thank you
@jishuguchhait1530 3 жыл бұрын
0:53 Body 6:12 Nut 11:38 Screw Spindle 18:12 Cup 21:47 Washer 24:30 Counter-Sunk Screw 28:30 Tommy Bar 32:30 Assembly
@VipulRoy69 2 жыл бұрын
Thank you so much sir. Please post this type of video
@praveensundaram4740 3 жыл бұрын
The way you teach worth more than applause ❤️🙏👍thanks a lot and keep doing .and my humble request is teach somthing big like v12 engine model, assembly and simulation.i hope you would consider this.thank you in advance
@CADxTraining 3 жыл бұрын
Currently I am doing the basic for beginners. Slowly I will move to advance. It will take some time.
@caseybahrabadi2185 7 ай бұрын
Excellent
@moin___3183 5 ай бұрын
These are lengthy process 😢😢❤❤
@swapnilpatil4238 2 жыл бұрын
Your teaching is Like, siri...... jitna kam utna dam
@notimetoplay7862 3 жыл бұрын
at washer and Screw my creo says Constraint invalid and i cant continue after it
@ROHITSHARMA-mq3rp 2 ай бұрын
HI Sir, in third part you made first revolve by selecting front plane but in second feature (hole)why did u select right plane, why u did not select front plane again 13:32 timing
@CADxTraining 2 ай бұрын
You can go with the front plane. That is also ok. But you will get a different orientation for the handle in the assembly.
@ramasundaram7432 2 жыл бұрын
How to download the CAD cero software,can you guide
@goginenirajesh8319 3 жыл бұрын
please upload a tutorial of top down assembly using skeleton modelling
@ROHITSHARMA-mq3rp 2 ай бұрын
Sir, I follow your design practice and try to sketch as you do but why my orientation of plane changes
@CADxTraining 2 ай бұрын
There are multiple reasons behind this. It's not easy to explain it here. You need to learn the whole sketching concept for this.
@MrGf1986 3 жыл бұрын
how do you keep the picture near the model tree?
@CADxTraining 3 жыл бұрын
Done by video editor. Not the part of the parametric.
@nejcpecar6303 2 жыл бұрын
CAN I GET STP DATA OF THE SCREW JACK?
@lakshminarayanan8838 3 ай бұрын
Sir, I can't able to change the hole dia in countersink for spindle sir .
@CADxTraining 3 ай бұрын
Check the unit of the part. I think you have taken the English unit.
@lakshminarayanan8838 3 ай бұрын
@@CADxTraining Ok thanks sir and your videos were very nice & clear too...
@akshaykumargs3317 3 жыл бұрын
When was available sir
@sambhavhaicorporations549 3 жыл бұрын
sir when i am taking line of 140 after taking centerline , my figure is not dividing in 70 ratio. How to resolve this?
@CADxTraining 3 жыл бұрын
Cancel it it and try one more time
@parthraval3883 7 ай бұрын
You should explain in detail and slowly which features, commands and steps you are using..... In this video i found myself having problems with this 3 things
@SRIKANTH-dc4wh Жыл бұрын
🙏
@ranjubala5732 3 жыл бұрын
Can you demonstrate how to generate raster image (TIFF) with custom dpi of a drawing in Creo and Autocad?
@CADxTraining 3 жыл бұрын
Can you tell me the actual reason behind this?
@ranjubala5732 3 жыл бұрын
@@CADxTraining Our customers demand *Product Assembly Drawing* in this format for approval purpose according to vehicle fitment.
@CADxTraining 3 жыл бұрын
You can use save as .Tiff to get the file. Have you tried it?
@ranjubala5732 3 жыл бұрын
@@CADxTraining It takes snapshot of drawing only. This option is seems to be useless.
@CADxTraining 3 жыл бұрын
That means you don't get enough resolution for that image. To get a high quality tiff image, there is another indirect way.
@crsh8572 2 жыл бұрын
where are you getting ypur blueprints from?
@CADxTraining 2 жыл бұрын
From engineering books
@crsh8572 2 жыл бұрын
@@CADxTraining interessting, thank you
@adityabodhak3055 10 ай бұрын
Sir when I tried to merg screw spindle then it merged but opposite merged please tell me what I can do.
@CADxTraining 10 ай бұрын
Go for flip option
@adityabodhak3055 10 ай бұрын
@@CADxTraining Sir,where is flip camaand located please Guide us.
@akashvandan 2 жыл бұрын
Dear Sir, I have a request for you , please make a video on creating car model using style tool. And also provide where we can get 2d drawings for practice and projects. thank you very much sir.
@mrchinna2259 10 ай бұрын
Which version of creo are you using sir
@CADxTraining 10 ай бұрын
Creo 6.0
@mrchinna2259 10 ай бұрын
@@CADxTraining thank you sir
@omkarsutar578 3 жыл бұрын
19:31 sir, why you don't use 8mm instead of parallel lines?
@CADxTraining 3 жыл бұрын
You can go with 8mm but you need to delete the parallel constant. But when you use 8 mm then the two lines will not be considered as parallel lines. You can even consider 8mm dimension and parallel constant by deleting 38mm dia. 8mm is not a critical dimension from assembly point of view so we can leave it or we may use it .
@omkarsutar578 3 жыл бұрын
@@CADxTraining It means not critical dimensions are less important. Thank you sir 👍🏻
@Izanumi 2 жыл бұрын
Which creo program is this?
@CADxTraining 2 жыл бұрын
Creo 6.0
@Izanumi 2 жыл бұрын
@@CADxTraining can we do this in 3.0
@Izanumi 2 жыл бұрын
Actually m super confused about the body part when I do that dimension of 70 it only streches upto half
@akshaykumargs3317 3 жыл бұрын
Tommy bar middle cutting sir
@akshaykumargs3317 3 жыл бұрын
Tommy bar who to doing sir
@akshaykumargs3317 3 жыл бұрын
Means extra drawings
@damodharanpc7060 3 жыл бұрын
Hi sir, can make a video, how to import EBOM table from csv file in creo
@CADxTraining 3 жыл бұрын
i didn't get your question. what do you mean by EBOM table?
@damodharanpc7060 3 жыл бұрын
Actually bill of material(BOM) in drawing is parametric. But sometimes we need to create BOM table manually and type values. If less number of parts we can type manually, but if more number of parts, i want to import data from csv file to BOM table
@CADxTraining 3 жыл бұрын
You mean to say, you want to copy data from csv table to the manual table in creo parametric?
@damodharanpc7060 3 жыл бұрын
@@CADxTraining yes
@CADxTraining 3 жыл бұрын
Yes you can easily convert a Bom table to a manual table.
@len3816 2 жыл бұрын
Can I have this drawing file please?
@CADxTraining 2 жыл бұрын
You can take snapshot of this drawing in in hd resolution from this video.
@riturajray5708 2 жыл бұрын
hey first i would like to thankyou because this really helped me. Second - i am facing some problem while drawing the washer part. Around 22:53 after getting the hole done you select sketch while being at the hole section and than you press sketch again and a new tab comes where you draw and that gets added right! i dont have that option, when i press sketch everything gets disabled for me. why is it so? and can you please suggest some other way to complete it! i am new to creo and this is my assignment so i dont know how to do it on my own. please it would be a great help.
@CADxTraining 2 жыл бұрын
That option is there in all the Creo release. Please check all the options available in your release.
@riturajray5708 2 жыл бұрын
@@CADxTraining thank you for your reply. I did check, I checked again and again it's not there. Else there's some issue with my system, ig it's not functioning well. Thank you very much for your reply. Also one req. Could you do a video on flange coupling!! I couldn't find a better screw jack on KZfaq other than your.
@Izanumi 2 жыл бұрын
CADX my spindle is not fitting when trying distance 10
@CADxTraining 2 жыл бұрын
Check both the parts. You will find something.
@Izanumi 2 жыл бұрын
@@CADxTraining something wrong with nut or a body
@laurentiudanceanu552 3 жыл бұрын
I dont find the cadx template
@CADxTraining 3 жыл бұрын
This is my template. You need to create your own template if you want.
@CADxTraining 3 жыл бұрын
This will help you. kzfaq.info/get/bejne/kM2cpZB6prjaiYk.html
@Izanumi 2 жыл бұрын
Sir can we convert this drawing onto 2d
@CADxTraining 2 жыл бұрын
Yes
@akshaykumargs3317 3 жыл бұрын
Sir send toomy bar drawing cutting crew Jack please how to do
@CADxTraining 3 жыл бұрын
You can watch this. kzfaq.info/get/bejne/i79jrM5n05O5j4k.html
@Muralis31 3 жыл бұрын
how to hide sub assembly files in a single view in drawing
@CADxTraining 3 жыл бұрын
Watch my video about filter in creo.
@scitech8087 Жыл бұрын
4.30 hours to complete
@akshaykumargs3317 3 жыл бұрын
Cross cutting
@akshaysarwade9543 3 жыл бұрын
Dear sir please provide pdf of drawings
@CADxTraining 3 жыл бұрын
You can take a snapshot from the video.
@xyz._.1234 3 жыл бұрын
Pls add drawing pdf link
@CADxTraining 3 жыл бұрын
You can take a snapshot in 1080 p resolution. All drawings are already given in the video.
@akshaykumargs3317 3 жыл бұрын
Can u send creo this drawing and how to login drawing
@CADxTraining 3 жыл бұрын
You can take a snapshot in 1080p resolution.
@akshaykumargs3317 3 жыл бұрын
Which one send me detiles sir please
@akshaykumargs3317 3 жыл бұрын
@@CADxTraining sir which one please send me where avilable
@CADxTraining 3 жыл бұрын
In the beginning of this video, you can take a snapshot in 1080p.
@akshaykumargs3317 3 жыл бұрын
Ok sir and thanks
@akshaykumargs3317 3 жыл бұрын
Will u sir that one most important
@akshaykumargs3317 3 жыл бұрын
Will u send air that drawing I mail u sir
@CADxTraining 3 жыл бұрын
You can take snapshot in 1080p resolution
@akshaykumargs3317 3 жыл бұрын
Not coming cutting cable drawing check mail sir
@akshaykumargs3317 3 жыл бұрын
Will u send Tommy bar drawing
@CADxTraining 3 жыл бұрын
Sorry about the drawing
@akshaykumargs3317 3 жыл бұрын
Assemby
@akshaykumargs3317 3 жыл бұрын
I send gmail sir
@akshaykumargs3317 3 жыл бұрын
Will u please
@CADxTraining 3 жыл бұрын
Check your mail
@akshaykumargs3317 3 жыл бұрын
Not coming sir can u please send me once sir it's most important
@akshaykumargs3317 3 жыл бұрын
I doing but not cutting once will u Plsssss
@akshaykumargs3317 3 жыл бұрын
Sir please sir I want if I doing I get my job please now no job for 1year
@akshaykumargs3317 3 жыл бұрын
Will u please
Creo sheet metal tutorials | creo sheet metal projects | Creo embossing | creo bend line | 3D models
CreoCAD Dynamics
Рет қаралды 1,1 М.