This video goes through all the features and step by step setup for the SCRIB3d ADVANCED 3d pen. You will be ready to start making after watching this.
Пікірлер: 31
@thevanquisher15192 жыл бұрын
Thanks a bunch! I tried to make a top hat for my first attempt but I couldn’t figure out how to stop it. A few months later, I watched the video and I can now stop it, I made a popsicle, and now can actually make 3d lines as shown, thanks!
@letdosomeexperimentstohave78153 жыл бұрын
Thx for this
@PantherU Жыл бұрын
Pretty great for welding multiple parts of a 3D print together.
@elissajmiller11 сағат бұрын
How do you make the filament stand up? It just falls straight down. We can’t make anything 3d.
@ilagalot57123 жыл бұрын
Thanks I just got my pen today
@Scrib3DPen3 жыл бұрын
thanks!
@cooldrew27253 жыл бұрын
Same
@staceymarksings85 ай бұрын
how do you change the filament?
@101yen2 жыл бұрын
hi, can this pen go beyond 180c? ABS usually melt at 240c as far as I know. My pen is topped at 180c
@Scrib3DPen2 жыл бұрын
There is a PLA setting and ABS setting, PLA tops out at 180, ABS setting tops out at 220C. ABS on a 3D pen is 200~220. 3D pens do not need to go up to 240C to extrude plastic, some printer also operate at 200~220 range.
@moonsprit Жыл бұрын
Trying to order this as a gift, what's the difference between yalls advanced pen and regular one
@Scrib3DPen Жыл бұрын
The Adv has more control, is more ergonomic and has better flow.
@FireflyX5L2 жыл бұрын
Can you press and hold rather than having it feed the filament out continuously?
@Scrib3DPen2 жыл бұрын
if you press the button it will start and if you press it again it will stop. holding the button and releasing it will not have an effect.
@SumProject182 жыл бұрын
@@Scrib3DPen this makes it impossible to do anything with it. These are trash
@billyeast68193 жыл бұрын
Constantly hitting the stop button on this pen . It looks ergonomic but in practice it is not
@Scrib3DPen3 жыл бұрын
you can double click for continue mode or you can hold down on the button and then release it. by holding down on the button that should help to prevent you from hitting the reverse button (I am assuming that is what you mean by the stop button as the forwards button is also the stop button when in continuous mode).
@karendean3925 ай бұрын
😅
@lizzie91213 жыл бұрын
Umm I got questions about scrib3d. It doesn’t go up straight it just melts down
@Scrib3DPen3 жыл бұрын
PLA takes 6 sec to harden ABS takes 3 sec to harden. Draw up stop the pen and hold for 3~6 sec before clicking the forward button again to continue. If you watch at around 2:50 were it details how to draw in the air.
@sherbet05033 жыл бұрын
It doesn’t stop where I want to do. How can I control it?
@hotgluehomegurl973 жыл бұрын
i think press the forward button again. I just got mine too. ill watch the video again
@Scrib3DPen3 жыл бұрын
click one to start the pen and once to stop the pen. Same button.
@emdee77443 жыл бұрын
Where can we buy this pen?
@Scrib3DPen3 жыл бұрын
you can find it on Amazon (www.amazon.com/dp/B08HM3X3D3?pd_rd_i=B08HM3X3D3&pd_rd_w=GNcBn&pf_rd_p=51cf0d17-50cf-4c89-b1a7-606703cfac11&pd_rd_wg=mrHm5&pf_rd_r=AANSQQXXZQ30Z4BRV7AB&pd_rd_r=dcb86a00-48ec-4e21-ab33-eed6f42b9151)
@xxtiamationxx35282 жыл бұрын
How do I change the filament?
@Scrib3DPen2 жыл бұрын
hold down on the reverse button for around 30 sec so the filament then start to reves ou of the pen. If you are still having issue please reach out to help@scrib3dpen.com
@xxtiamationxx35282 жыл бұрын
@@Scrib3DPen thank you
@marialcantar89523 жыл бұрын
How do I turn it off
@Scrib3DPen3 жыл бұрын
unplug it, if it's left plugged in and the motor is not on then it will go to sleep after 5min ie heater will turn off.