I'm installing one now. I can't believe it didn't come with installation instructions. Thank you for this video.

I recently had this installed with a new 7’9” door, and I’m very happy this far. Quiet, smooth, and the overhead clearance is great to have. I haven’t set up the Wi-Fi capabilities yet, the old-school part of me gets a little nervous when it comes to that, from a security standpoint.

Good install video! Using this and the official Chamberlain one I was able to get mine installed and working. Very happy with it now its all working (very quiet!) but had to go through some headaches I'll talk about here in case anyone else runs in to the same issues. 1 - The light was not paired to the opener out of the box! This was insanely annoying! Turns out this is very simple to fix (not documented anywhere from what I could see though), on the light there is a button next to the small green led light located on the side of the light that you can press and use to sync to the opener, just press the 'learn' button on the opener or control unit along with the sync button on the light and they should pair up! 2 - The single button remote was not paired to the opener out of the box. Also annoying as all documentation seemed to indicate it just works out of the box. I was unable to get this to sync to the opener by pressing 'learn' and holding the single button until the door opens. What got this working was after installing the MyQ app and adding our door opener, we were able to 'add' a remote by selecting the single button model in the app and following the instructions, for whatever reason this got us working. 3 - Error messages regarding lift/down unexpected/excess weight (4-1). This one is going to be specific to each person, but what worked for me was to tighten the set screws on the collar closer to the unit by 1/4 turn each. During install you're instructed to tighten the set screws on the garage door bar side by a specific amount but that same instruction is not specified for the set screws on the opener side. In other words make sure the set screws are nice and snug.

Very nice. I also switched my openers to this style. I didn’t use the lights but rather a smart switch and linked to my main ceiling lights, which also shut off via timer.

Awesome video with clear steps and tips. Does this unit come with hardware for installation to concrete or masonry, instead of wood/drywall/sheetrock?

Okay, your opener unit flexes slightly back and forth when opening/closing just like mine. I suppose that is okay then.

Great video... Have a safe and happy Thanksgiving to you and your family...

thanks

Thanks for going over the clearance dimensions. They should really list all the critical dimensions on the box so you can see what you need before you buy it.

Nice video and thank you for taking the time to make it. I am currently looking at new garage doors and wall mount openers; one for each door as you have. I am trying to choose a brand and wondered if you had thoughts on which brand is better? Liftmaster vs Chamberlain or another ? I gather Liftmaster have developed a model without a cable tension sensor but it is problematic.

Thank you for the set up instructions. Some of them go so fast I could not get it.

Don’t know if you r answering comments. If have a garage that the door is 2 feet out from the front of the house. At the house portion a support beam comes from front of house through the garage keeping me from being able to take the chain pull unit all the way above the garage door any ideas?

I having problems to make the light working whit the motion sensor any advice??

Thanks for the video. I just installed one of these units on one of my doors but I am struggling to get it into learn mode. I was hoping you could tell me what the lights look like when you double press the "learn" button. All it does is make my steady orange light flash. There's no red light like the instructions say there should be. Thanks for you help!

Where or how can I check the profile for my door?

Hi..where is the learn button? I need to train some universal openers? thanks

hi. can i use this opener for the double garage door ? thanks

Thanks - did I miss the part where you actually showed how the locks engage?

Installed mine. Door is balanced. Goes up fine. When attempting to go down, wire uncoils from drum. Looking for suggestions for a solution

I just installed same one but had it lose programing the other day (door would attempt to close and stop). I reprogrammed it and was fine again. Have you had this happen?

That body is moving clearly in the video, why? That doesn't seem ok nor correct.

Can’t get over this is $400+