Sculpfun S30 Pro Max 20w Output Laser.

Рет қаралды 21,653

Жыл бұрын

Laser cutter: affiliate.geekbuying.com/deep...
699GBP for SCULPFUN S30 Pro Max with the coupon: NNNUKS30
Great for engraving too of course but I use mine mainly for cutting.

Пікірлер: 64

@RetroSteamTech Жыл бұрын

That's a very nice bit of kit 👍👍 I like that Baker Fan, looking forward to the video. Cheers, Alan.

@SCULPFUNReal Жыл бұрын

Thank you so much for choosing Sculpfun!!

@rolanddube2169 Жыл бұрын

It looks like Mrs. Myfordboy will be having you make Christmas ornaments... 😀 Great video as always, I love your work!

@mastermaker666 Жыл бұрын

The ONE thing I keep hoping to see in a laser review video is trying to cut flooring laminate as it is an amazingly cheap and strong material(basically anything you could make out of comparable thickness or slightly thinner alu-plate you can make out of flooring laminate) usable for a whole host of different projects(tools/machine-chassis/storage etc...)

@myfordboy Жыл бұрын

I would try some if i had any.

@MattTester Жыл бұрын

Seems much more capable than the 15W unit I have, I will look into air assist. The smoke and the smell really puts me off using it though as I don't have much ventilation.

@IonFontxo Жыл бұрын

Same here. I made an enclosure with MDF following some videos I watched here. Nothing fancy, just functional with an extractor going out the window.

@sannyassi73 Ай бұрын

Without an enclosure or air assist I don't think I'd ever use my laser. My enclosure is built with cardboard/duck tape/hot glue and has held up for 8 Months so far. Due to it being cardboard it's easy to test prototype ideas- I've got a cardboard filter box as well built in. It does surprisingly well- no more smoke, no more smell. Sometimes I forget to turn the fan on and you can tell the difference within the first minute of a burn- the only thing that costed money was mostly just the fan, which I believe was about 30 USD- then a few hot glue sticks and half a roll of duck tape. I will be building an MDF box once I have the time using the cardboard setup I have now as a template. As for air assist, once you get even a cheap system setup you'll likely wonder how you ever worked without it before, it makes a huge difference!

@jonpardue Жыл бұрын

Looks like it cuts anything the K40 can handle, without the need for water cooling. Well done!

@myfordboy Жыл бұрын

I have a K40 but this one is better, larger bed area and more portable. It cuts better than the K40 smaller beam and kerf. Cuts faster.

@planckstudios Жыл бұрын

Looks great. Any luck w/ 12mm ply? curious to see those edges up close and how pronounced the kerf angle is on those deeper cuts

@myfordboy Жыл бұрын

I don't have any to try but see no problem cutting, maybe make a couple of passes.

@NoXs4u Жыл бұрын

First of all I find it remarkably funny that for the last 5+ years I bump into your videos for different subjects. It started when I wanted to know more about lathes. Then, later on I was researching diy aluminium casting. And now this laserthing. So thanks for sharing your interests and knowledge in (previous) videos. Learned a lot. My question for this video; did you use the two pin Molex "Emergency" connector on the Sculpfun PCB for hooking up the E-Stop button? If so, is it just a matter of replacing the jumper with a NC E-stop button? Thanks in advance!

@myfordboy Жыл бұрын

Looks like I am just one step ahead of you with interests! For the e button I used a regular NC button wired in series with the low voltage supply lead from the power supply. I did not cut the exsisting lead. This plugs into a matching socket wired to the button and I added a new lead with plug from button to the machine inlet. This way I can easily take out the machine from the enclosure if needed, nothing to unwire.

@dansam1395 Жыл бұрын

interesting you cut foam sheets. are they covered with paper on both sides? diode lasers unfortunately don't cut depron

@myfordboy Жыл бұрын

Paper both sides. Using different settings I am able to cut right though or just through the top paper.

@gcase08 Жыл бұрын

I just had to return this machine as it could not cut round circles. I loved the features, power and the programmable air assist but if it can't do a basic thing like cut round circles then all the great features really mean nothing.

@quetzalcoatlhermeticus8024 Жыл бұрын

Do you know why it doesn't cut circles?

@piotrdivineacoustics5754 Жыл бұрын

Hi, I have question about airpump. Can it be turned on manually or just via lightburn?

@myfordboy Жыл бұрын

You can turn it on in Lasergrbl or Lightburn. Using lasergrbl it is either on or off. With lightburn you can start and stop within an engraving. Not an issue with Lasergrbl though, just do one burn for the engraving, air off and a second for cutting, air on.

@alexanderhurley6738 Жыл бұрын

Does the SCULPFUN S30 Pro Max have a spot/cross hair for setting up?

@myfordboy Жыл бұрын

The laser will frame the size of your design with a low level spot so you can position your material before you run at full power. You can also centre the spot to the centre of your design.

@timmienorrie Жыл бұрын

Excellent review although a fume cabinet seems a must for these beasties.

@francistaylor1822 Жыл бұрын

Agreed. Personally I wont go near a laser with proper full fume filtration/extraction and proper eye shielding. Which is a pity as I really want one. I do like that he made the enclosure, I would suggest doing a DIY carbon filter like people use for the Voron 3d printer (nevermore max) as that would certainly help with the fumes. How do you know though that the viewport is blocking all the laser light?

@romantashevRT Жыл бұрын

Hi.. great informative video. Could you please share the stl for the extended screws?

@myfordboy Жыл бұрын

Sure, leave your email or email me.

@kevinrivas7600 4 ай бұрын

Hello, nice content. At what speed this machine can cut 6mm MDF ? Thanks!

@myfordboy 4 ай бұрын

Sorry I don't have this machine anymore and looks like I did not record the speed. The machine is good and I can recommend it. I have replaced it with an xTool P2 laser.

@jewijk Жыл бұрын

Like the thumbscrews for laser focus 👍

@IonFontxo Жыл бұрын

Thanks a lot. This is a great video. Just got this machine and I was wandering what power are you using? Cheers.

@myfordboy Жыл бұрын

For cutting I use max power and vary the speed according to the material. I have found for thicker ply which can vary in consistency it can be better to take 2 passes at a faster speed rather than a single pass at a slower speed.

@IonFontxo Жыл бұрын

@@myfordboy Thanks a lot. That makes a lot of sense. I'll give it a try later on.

@edcpielazteca2936 Жыл бұрын

Hola puedes enseñas mas fotos de tu caja que le fabricaste a tu laser tengl el mismo modelo y quiero una caja igual

@myfordboy Жыл бұрын

Full build was shown here kzfaq.info/get/bejne/frRhmcWbva2ncYU.html email me if you would like dimensions.

@marcyvanbeaulieu5109 6 ай бұрын

400 x 410 mm est un leurre puisque es réelles dimensions sont 363 x 370 se, à l'interne.

@robman80808 Жыл бұрын

Superb video, thanks! Do you have plans for your enclosure? It looks incredible.

@myfordboy Жыл бұрын

No plans but there is a video here. kzfaq.info/get/bejne/frRhmcWbva2ncYU.html I can sketch out the dimensions if you wish.

@robman80808 Жыл бұрын

@@myfordboy thanks. I just watched the video and it looks like I could work it out from that. Great woodworking skills, btw!

@jsa2001 Жыл бұрын

What's the cost in electricity to run the 20w laser.

@myfordboy Жыл бұрын

Machine power is quoted as 84w. Not expensive to run.

@peanutman314 Жыл бұрын

This can really cut through 3mm MDF in a single pass? All the other videos for this model do it in multiple passes.

@myfordboy Жыл бұрын

It certainly can cut in one pass at around 400 -450mm/min.

@jonnowak8578 Жыл бұрын

Awesome video! Just bought this laser. Any chance you’d be willing to share the 3D printer files for the screws?

@myfordboy Жыл бұрын

Yes, no problem.

@jonnowak8578 Жыл бұрын

@@myfordboy thank you again for sharing these! ❤

@yamsingcreative Жыл бұрын

Just taken delivery of this beast and you video was very helpful. Love your printed focus knob extensions - I don’t have the 3D print facility so any chance you could sell me a set? Also just out of curiosity, were you running all off those cut tests at 100% power? If not what were the power settings ?

@myfordboy Жыл бұрын

The wood cuts were all at 100%. The foamboard was cut at 1000mm and full power. score was 2500mm and half power. Happy to print some screws for you. I don't have any more of the M4 x 50mm socket head screws i used. You can source your own or i can buy more. email me myfordboy at g mail. com

@steveedwards6451 Жыл бұрын

I do have a 3d printer, and just ordered this machine,. is there a possibility you could send me the file for the Focus Knob Extensions? Also just curious, do you know of a file on Thingiverse or another site for some leg extensions for using another brand of rotary roller? Thanks

@brightsides6581 Жыл бұрын

Hi can you make a model of a building up/contracting house 🏠 which can be really viewed/understood by a common person who wants to build up a new home and you can help them by building a model house 🏠 bit by bit like rooms,bathrooms each and every room,attic,etc etc

@myfordboy Жыл бұрын

If you draw the part in 2D the machine can cut it out.

@GrandadIsAnOldMan Жыл бұрын

I would love one of those, but even if I could afford it, I simply don't have the space to set one up without doing a lot of tidying up. Tidying up is not one of my skills.

@francistaylor1822 Жыл бұрын

it is one of mine, but I (seriously) reckon I spend about 70% of my project time tiding up and/or organising.

@Stevon2012 Жыл бұрын

$844 dollars and limit switches are exposed? It just looks like a $300 laser to me, I understand that the wattage is doubled and the holy grail linear rails, but the linear rail is only on the X axis? Why doesn't it come with the Y axis too? There is also no cable management but zip ties. It just looks cheap to me... You would be money ahead to by a cheap laser and add the sculpfun laser head to it. It wouldn't cost near as much... I just bought a Comgrow 10watt, air assist kit, and an enclosure for $355 delivered to my door. I could spend 2-3 hundred dollars and add that laser head... It may be what I do. Good video regardless, thank you for sharing. Keep up the good work!

@iteerrex8166 Жыл бұрын

A word of caution about lasers. You MUST have eye protection and air ventilation. I’d say laboratory-grade glasses, especially if you’re a new user. If you think wood smoke is somewhat safe, think again. All plywood have tons of awful glue.

@be007 Жыл бұрын

how does the programming work ?

@myfordboy Жыл бұрын

I am using software from lasergrbl.com you can also use Lightburn. You import your design into this and then set the laser speed and power from it.

@SantiLiebana Жыл бұрын

3d stl files please¿

@myfordboy Жыл бұрын

For the screws? email me.

@brightsides6581 Жыл бұрын

Like civil engineer's does

@MegaBlackJoe Жыл бұрын

I hate videos without safety precautions for class 5 lasers.

@philiphoeft6100 Жыл бұрын

Do you think safety instructions might be in the box.

@kenton393 Жыл бұрын

p̷r̷o̷m̷o̷s̷m̷ 😝

@336mrk Жыл бұрын

Sculpfun has a rubbish and dishonest shipping service I ordered mine on the 5th December thinking I would get my machine shipped by DHL 16th December still waiting!!! AVOID AT ALL COSTS 👎🏼

@myfordboy Жыл бұрын

DHL have major shipping issues at the moment due to postal strikes and time of the year.