SeaDoo Engine Gateway

Рет қаралды 10,164

Жыл бұрын

If you like these videos, please subscribe. How to get your Garmin EchoMap UHD to display engine data on a SeaDoo Switch. Needs a NMEA 2000 network. This video will show how to install the NMEA 2000 network and the Yacht Devices Engine Gateway. SEE COMMENT BELOW ABOUT FUEL LEVEL. Check video on Yacht Deices Tank Adapter for fuel level. If this has helped, please like and subscribe.
Yacht Devices Engine Gateway: amzn.to/45pgszH
Adapter Cable: yachtdevicesus.com/collection...
Garmin NMEA 2000 Starter Kit: amzn.to/3pEyZYF
Garmin NMEA 2000 T Connector: amzn.to/3BnpXlb
MicroSD Card: amzn.to/42P56D6
YDEG.txt -Copy the text below and paste to your microSD card as the YDEG.txt file. Copy all to where it says # END OF FILE.
Current configuration of Yacht Devices Engine Gateway YED-04
Firmware: 1.36 05/5/23
www.yachtd.com/downloads/#yde...
If no data displayed then change CAN_SPEED to 250
ENGINE_CAN_SPEED=500
ENGINE_0 changed to 1 and ENGINE_1 changed to OFF
ENGINE_0=1
ENGINE_1=OFF
ENGINE_2=OFF
ENGINE_3=OFF
ENGINE_4=OFF
ENGINE_5=OFF
ENGINE_6=OFF
ENGINE_7=OFF
HOURS_OFFSET=0
If fuel rate and other data not available, change BRP_ROTAX from ON to HANDSHAKE
BRP_ROTAX=ON
SMARTCRAFT=OFF
VOLCANO=OFF
EDC2=OFF
MEFI4B=OFF
Reset when switching SMARTCRAFT or MEFI4B settings, use CALIBRATE_TRIM
TRIM_ZERO=28708
TRIM_STEP=128
EXHAUST_TEMP=ON
INTAKE_MANIFOLD_TEMP=OFF
NMEA_BATTERY=KEYSWITCH
BATTERY_0=0
BATTERY_1=1
BATTERY_2=OFF
BATTERY_3=OFF
BATTERY_4=OFF
BATTERY_5=OFF
BATTERY_6=OFF
BATTERY_7=OFF
NMEA_ALTERNATOR=KEYSWITCH
If no display, change to FUEL=DIESEL
FUEL=GASOLINE
FUEL_0=0,PORT
FUEL_1=0,STARBOARD
FUEL_2=OFF
FUEL_3=OFF
FUEL_4=OFF
FUEL_5=OFF
FUEL_6=OFF
FUEL_7=OFF
FUEL_8=OFF
FUEL_9=OFF
TANK_CAPACITY_0=DEFAULT
TANK_CAPACITY_1=DEFAULT
TANK_CAPACITY_2=DEFAULT
TANK_CAPACITY_3=DEFAULT
TANK_CAPACITY_4=DEFAULT
TANK_CAPACITY_5=DEFAULT
TANK_CAPACITY_6=DEFAULT
TANK_CAPACITY_7=DEFAULT
TANK_CAPACITY_8=DEFAULT
TANK_CAPACITY_9=DEFAULT
TANK_CALIBRATION_0=OFF
TANK_CALIBRATION_1=OFF
TANK_CALIBRATION_2=OFF
TANK_CALIBRATION_3=OFF
TANK_CALIBRATION_4=OFF
TANK_CALIBRATION_5=OFF
TANK_CALIBRATION_6=OFF
TANK_CALIBRATION_7=OFF
TANK_CALIBRATION_8=OFF
TANK_CALIBRATION_9=OFF
MDI_PROP_MESSAGE=ON
MDI_AUX_MASK=000000
MDI_SYS_FAULT_MASK=000000
ALERT_0=OFF
ALERT_1=OFF
ALERT_2=OFF
ALERT_3=OFF
ALERT_4=OFF
ALERT_5=OFF
ALERT_6=OFF
ALERT_7=OFF
ALERT_8=OFF
ALERT_9=OFF
ALERT_WARN1_MASK=000000
ALERT_WARN2_MASK=000000
ALERT_POWER_REDUCTION_MASK=000000
NMEA_ALERT_MASK=FFFFFF
TRANSMISSION_0=3
TRANSMISSION_1=4
TRANSMISSION_2=OFF
TRANSMISSION_3=OFF
TRANSMISSION_4=OFF
TRANSMISSION_5=OFF
TRANSMISSION_6=OFF
TRANSMISSION_7=OFF
TRANS_ALERT_0=OFF
TRANS_ALERT_1=OFF
TRANS_ALERT_2=OFF
TRANS_ALERT_3=OFF
TRANS_ALERT_4=OFF
TRANS_ALERT_5=OFF
TRANS_ALERT_6=OFF
TRANS_ALERT_7=OFF
TRANS_ALERT_8=OFF
TRANS_ALERT_9=OFF
TRANMISSION_ALERT_MASK=1F
WATER_DEPTH_OFFSET=OFF
WATER_SPEED_CORRECTION=OFF
WATER_TEMP_OFFSET=OFF
PASS_PGN=OFF
PASS_ADDR=AS_IS
J_PASS_PGN=OFF
J_PASS_ADDR=210
For ENGINE_0 or TRANSMISSION_0, data instance +1 will be used for ENGINE_1, etc. SUBSTITUTE_BOOST=OFF
SUBSTITUTE_FUEL_PRESSURE=OFF
SUBSTITUTE_OIL_PRESSURE=OFF
SUBSTITUTE_OIL_TEMP=OFF
SUBSTITUTE_CLNT_PRESSURE=OFF
SUBSTITUTE_CLNT_TEMP=OFF
SUBSTITUTE_TRANS_PRESSURE=OFF
SUBSTITUTE_TRANS_TEMP=OFF
End of file

Пікірлер: 69

@dozer8065 4 ай бұрын

As a sea doo tech im installing this on a customers boat, he sent us these videos, he wants it done and it can be done, ive had a blast doing this, these videos are top notch!

@letsrolldiyauto1532 4 ай бұрын

Thanks

@raypabs5374 5 ай бұрын

I love your Seadoo Switch videos. Went to the NYC boat show yesterday and your knowledge is reinforcing my desire to buy this pontoon. Thank you!

@letsrolldiyauto1532 5 ай бұрын

Thanks. I'm glad they help.

@isaacbeja4073 Жыл бұрын

Awesome job!

@letsrolldiyauto1532 Жыл бұрын

Thanks

@vincentfarrell3935 Жыл бұрын

The videos your making are great ! Keep it up! Where are you from can you come do this to my switch ?

@Drimplant Жыл бұрын

I'm in Merritt Island Florida.

@MrJenya19741529 11 ай бұрын

amazing video , clear , step by step instruction , old school !!! super ! my question is i have twin engine challenger 230 , how to set up two engines ?

@letsrolldiyauto1532 11 ай бұрын

Sorry, you'll need to check out the YachtDevices website for that information. But there are settings n the programming to allow for multiple engines. The device itself will do it, but I imagine you'd need a common diagnostic port that handles both engines. Then just plug it in and set the parameters for your set-up. Tech support at Yacht Devices is excellent in providing support for specific applications.

@wannabeRanger0321 Жыл бұрын

Really thankful for your videos! Even if they’re complicit in the draining of my bank account. You should get affiliate links! Can you point me in the direction of what I need to make it read the fuel tank?

@Drimplant Жыл бұрын

Yes. First, you can go to settings > My Vessel. Then for fuel select Flow. Enter 29 for the gallons and have a full tank. The flow rate, which is read by the CAN, will calculate and display the remaining fuel. While not 100% accurate, it is pretty close. When you refill the fuel tank, fill it full then in Settings > My Vessel > Fuel, select Refill and it will reset the amount back to the full 29 gallons. To have the fuel gauge actually read, Yacht Devices makes a fuel tank module. It would require another NMEA 2000 t-connector and attachment to the fuel sensor and a 12 vdc reference. I have the wiring schematics and will be looking at the best place to tap into the fuel sensor. The sensor is part of the fuel pump and not the easiest to get to. Wiring does go to the console and I know the pins used. I’ll have to see how easy it is to get to it. Chump Zillow on the Facebook Switch group is looking into it also. We are communicating to get it done. It is another $250, though. When I get it done, I’ll do another video on it.

@hammerweld-jp9qf 11 ай бұрын

The Amazon Link is for style : (Raymarine Seatalk Ng Compatible )or should I be purchasing style: ( NMEA 2000 (DEVICENET) MICRO MALE). Awesome video. Thanks

@GatorDoc1987 10 ай бұрын

Frank, if my previous request is not a good idea secondary to variability. Perhaps I can drop by your place in Merritt Island and give it a shot if I can’t get it working. I bought a 2023 18 foot 230 hp Sea-Doo switch. My home is in Vero beach, but I keep the boat in Leesburg Florida.

@letsrolldiyauto1532 10 ай бұрын

You can do that. I won't be available until after the 29th, but any day then is fine.

@GatorDoc1987 10 ай бұрын

Frank, I have watched all of your videos on the Sea-Doo switch. They have been really helpful and I thank you for that. I’m not much of a computer guy, but I am otherwise fairly handy. Do you have any interest in creating a micro SD card with the appropriate verbage on it and I could compensate you for your time and inconvenience.

@letsrolldiyauto1532 10 ай бұрын

No compensation necessary.

@georgefreiberger5282 Жыл бұрын

Frank - Great video can you add the link to the Fuse /Wire RJ11 Directwire Radar Mount kit

@letsrolldiyauto1532 Жыл бұрын

amzn.to/445Vi8d

@letsrolldiyauto1532 Жыл бұрын

Note: The fuel level is only calculated from the fuel flow rate and the amount of gas you input. It is not reading the fuel sensor. When you fill up your tank, you have to go into the settings and re-input the gallons. The fuel sensor on the Switch is not connected to the CAN. There is another device by Yacht Devices that can be installed to read the fuel sensor. This device is for another video.

@anthonys7534 Жыл бұрын

The Yamaha jet boat community would love to have the NMEA2000 connectivity, however no one has been able to crack the code yet

@chriskirchoff7738 11 ай бұрын

Didn't see in install video of how it gets connected to the Switch engine?

@letsrolldiyauto1532 11 ай бұрын

@@chriskirchoff7738 The Engine Gateway connects to the CAN bus. The end of this is plugged into a dum my port on the coolant tank.

@MoniandFredsillyrianGaming 6 күн бұрын

@@letsrolldiyauto1532where is the engine gateway port located

@letsrolldiyauto1532 2 күн бұрын

@@MoniandFredsillyrianGaming It connects to the CAN Bus. On the video I show where on the coolant tank the end of the CAN Bus line is located.

@timgawlick4100 11 ай бұрын

Question. How long does the motor have to be running in the water. Before you get Diles on your gauges or the gauges start to work. I’ve hooked mine up and tried it on land. Put the boat in the water on the trailer and fire the motor up in the water. And my gauges still do not seem to want to work. I reprogrammed the SD card one more time figured I might’ve got something wrong. But I’m still trying to get it to work.

@letsrolldiyauto1532 11 ай бұрын

It does not have to be in the water. Check the lights on the engine gateway device. There should be two green flashes. One green says the device is working, the second says it’s communicating with the network. If you don’t have that, reprogram and check all the connections and make sure your NMEA 2000 is set up correctly with the terminators on each end. And make sure you have the network powered. If you have that, Go to the Garmin settings. Make sure the correct engine is selected. You may need to change from 0 to 1 depending upon how you programmed the device. Make sure your device appears in the NMEA 2000 devices on the Garmin. Go for the auto gauge setup.

@kennedycorp 10 ай бұрын

Thanks for your tutorial Frank. I've followed your instructions and used your file but it isn't working quite right. I get RPM, Trim, F/N/R, Voltage, Engine Temp Info. But I don't get boost info or fuel flow. When I go to the settings to enter in the fuel tank capacity I have no options in that screen other then the "Remaining Fuel" toggle which is set to "Fuel Flow". Any ideas? I've tried resetting the Garmin to factory defaults but I can't seem to get the missing info to display.

@letsrolldiyauto1532 10 ай бұрын

Boost doesn’t work for me, either. I assumed it was because I didn’t have the 230 supercharged engine. For fuel flow, make sure you have the correct tank selected on the Garmin and set to fuel flow. This solution should be in the Garmin settings

@Rainor2020 Жыл бұрын

Very Informative Channel ! Nice work! Probably should cut your zip-ties flush so you do not get cut in the future when poking around the engine. 😛

@letsrolldiyauto1532 Жыл бұрын

I do cut them. Just didn't before taping was done. Thanks

@mannyleggio3013 Ай бұрын

Hey Frank. Thank you for all the videos. Awesome. Question, do I need to download the firmware first, then edit it, or just create the txt file and copy to the SD card and install it on the device?

@letsrolldiyauto1532 Ай бұрын

If there's a firmware update, then download the firmware. If not then just copy the txt file to the SD card and put it in the device.

@mannyleggio3013 Ай бұрын

@@letsrolldiyauto1532thank you so very much. You’re the best.

@johnbuchan1161 10 ай бұрын

I cannot get the yacht devices to work with the engine even though I’ve check the continuity of the harness wiring to the yacht device and observed the CAN H and L signals on the connector pins

@letsrolldiyauto1532 10 ай бұрын

Make sure you are seeing two green flashes on the yacht Devices LED. One green flash is properly connected to the CAN, the other is properly connected to the NMEA2000 network. If you are getting two green flashes, then check the settings on the Garmin. Are you using the programming I provided in the description section? If yes, (and you re getting the two green flashes) then make sure you select the correct engine in the Garmin.

@wannabeRanger0321 14 күн бұрын

What’s the easiest way to feed the wire to the engine? Do I need to pull up decking? Looks like the pass through goes through the outer toon

@letsrolldiyauto1532 13 күн бұрын

You do need to remove the deck under the captain's chair, as shown on the video.

@sweeperb4938 Жыл бұрын

Do you know how to get the water and air temp to work on the garmin

@letsrolldiyauto1532 Жыл бұрын

You'd need to add the appropriate sensors to the NMEA 2000 network. You could also add a Garmin SiriusXM receiver. But these are expensive and require a subscription. Google Garmin SiriusXM.

@scotthutchins6035 Жыл бұрын

Great video so where do I start to copy? ENGINE_0 changed to 1 and ENGINE_1 changed to OFF all the way through #End of file? Thank-you

@Drimplant Жыл бұрын

Start with # current….. to the # end.

@scotthutchins6035 Жыл бұрын

@@Drimplant ok thank you I believe my head lights will be here today :) and waiting on the equipment to do the gateway.

@georgefreiberger5282 3 ай бұрын

Frank - QQ - I have the ski module like you could you show how you connected everything? Pictures or video would be great. Thanks for you consideration.

@letsrolldiyauto1532 3 ай бұрын

If you have subscribed, just look at my videos. I have one on the Ski Module that shows how to install it. kzfaq.info/get/bejne/jcejhqti2bKrqWw.htmlsi=xkIxuXi8pN81EXAf

@georgefreiberger5282 3 ай бұрын

Yep saw that just didnt know how to connect the engine gateway and the ski module as dont they use the same port?

@Drimplant 3 ай бұрын

@@georgefreiberger5282it doesn’t. It just adds to the CAN bus and will spread as an option on the console.

@kevinperryman4322 Жыл бұрын

This is great info. I've still got a burning question... where does the adapter/engine gateway plug in on the actual engine? Can you provide a diagram/picture/crayon drawing of where the plug is? Thanks!!!

@letsrolldiyauto1532 Жыл бұрын

Look at the coolant reservoir tank. Facing you towards the bottom is a plug. This is the end of the CAN BUS plug. it is in the dummy port on the coolant reservoir tank. Plug into this plug and then the other free end goes back there. You just add to this chain.

@kevinperryman4322 Жыл бұрын

@@letsrolldiyauto1532 Frank! Awesome info. Your opinion, the fuel adaptor worth it from Yacht Devices?

@letsrolldiyauto1532 Жыл бұрын

@@kevinperryman4322 No. It works, but the Sea Doo tank has a stepped fuel gauge not a continuous or variable resistance type. So it will read the same fuel amount until the tank level drops to the next step. Then it will display that amount. Other than telling gallons, it will be identical to the step gauge on the dash. I have my settings on the Garmin to display remaining fuel based upon fuel flow. While I have the tank adapter installed, I rarely use it.

@JohnBraman413 Жыл бұрын

what's the link for that fuse holder wire?

@letsrolldiyauto1532 Жыл бұрын

amzn.to/3MROVQf

@servicemaster2014 Ай бұрын

In getting to the final set up of the Engine gateway for my 2023 21' 230 hp supercharger I have found the Bi-color LED on the Device to blink red rather than green. However; when i turn the garmin on, the device light flashes light green then back to red then back to green then back to red and so forth. I believe I have set the wiring up exactly as you showed on the video. Just wondering if you would have a solution. Also I was wondering if I set up the SD card correctly by copying and pasting the text as follows: BRP_ROTAX=ON ENGINE_CAN_SPEED=500 ENGINE_0=1 ENGINE_1=OFF FUEL=GASOLINE

@letsrolldiyauto1532 Ай бұрын

Copy and paste the code I provided below the comments. Re-flash the Engine Gateway. Make sure your NMEA2000 network is powered. Did you use the adapter cable? The first color flash indicates the Engine Gateway. Green indicates that the data from the engine has been received by the Engine Gateway. The second flash indicates the condition of the NMEA2000 network. A red flash indicates that no data is sent or received to the network. I'm going to assume that the red flash is the second flash. So you need to check the NMEA2000 network for proper installation and that it is powered. If you connected everything as in my video, then you'll need to make sure the ignition is ON so that the network is powered. Double check with a meter that the network is indeed getting power.

@servicemaster2014 28 күн бұрын

@@letsrolldiyauto1532 Hi Frank, thank you for your quick response!! I have copied & pasted the code in it's entirety that you provided below the comments to the SD card starting with the Bold words: "If no data displayed then change CAN_SPEED to 250" and ending with the last code just prior to "End of File". Should I have copied the code text only rather than copying the bold statements as well? I then checked with my meter the voltage coming out of the red wire that I had plugged in to the lower left corner of the fuse box and then to the yellow NMEA 2000 cable. I checked the voltage inside of the red cable where I could pull apart the small black twist apart fuse holder. The meter showed 12 volts with the ignition on and showed no voltage with the ignition off. I then re-flashed the SD card to the device with the ignition on. Device blinked red. I then turned on the Garmin. The device showed 2 blinking green lights, 5 seconds apart showed 2 blinking red lights then repeating itself. I did connect the adapter with the female end of the adapter to the mail end that I removed from the dummy port on the front of the coolant tank which left a male end that I put back to the dummy port. Obviously I connected the other end of the adapter to the in line connection end of the device which left an unused male end. Honestly I couldn't see any other way it would connect. I did try to add a photo of how everything is connected in the engine compartment for you to view but my computer would not allow me to do so. Is there a way I can send the photo via text message or email? You could DM me at 435-630-6155. Thank you in advance.

@letsrolldiyauto1532 28 күн бұрын

@@servicemaster2014 On your NMEA backbone, each end - that is in-line with the length of the backbone - need terminators. Devices do not get plugged into these ends. Only the port(s) coming out at 90 degrees from the backbone should have devices connected. In the basic one device network, there should be a terminator at one end, then a power connector on one 90 degree port, the device at another 90 degree port and then a terminator at the other end. Are you set up this way?

@servicemaster2014 28 күн бұрын

Yes, I have set up the back bone precisely the way you described with terminators in line on both the top end and bottom end. Yellow power cable to 90 in center of back bone. Top 90 cable to Garmin. Bottom 90 cable to device.

@depdoc 28 күн бұрын

I’d suggest contacting Yacht Devices support. It’s possible your device is defective.

@terrywitte9109 Жыл бұрын

Which connector or where is the connector in the engine compartment?

@letsrolldiyauto1532 Жыл бұрын

@terrywitte9109 Жыл бұрын

@@letsrolldiyauto1532 do I leave the card in after activation or remove it ?

@letsrolldiyauto1532 Жыл бұрын

@@terrywitte9109 Remove it and place the adhesive covering over the slot (included with the Engine Gateway).

@MrDougAnton 2 күн бұрын

Where are you? Can I pay you to do this on my boat. I am in North New Jersey.

@letsrolldiyauto1532 2 күн бұрын

Well, I'm in Florida. And DIYer. If you need it added and do not want to tackle it yourself, I would imagine any marine electronics shop would have a technician who could do this for you.