I’ve always thought you sound country AF but when you listen to what you’re talking about you’re a pretty intelligent and mechanically inclined guy. Thanks for that content.

Thanks for sharing this. It’s a real time saver - would have taken a long time to figure this out thru trial and error. Makes sense to have overlapping gears between ranges. Also makes me wonder why every OEM doesn’t do this.

Good info, when I go out on the road from my field there is a big hill, so I always start in 9th, never had a problem. Someone at New Holland knew what they were doing.

Not read all the comments. You are correct , it gives you a low gear to start off in that range. The reason for this is the 1-4 gears are synchronized, and the range gears l-m-h are not, so if starting off with a heavy load in 4 gear medium range, it would be difficult to shift up the range to high due to no synchro. So having a lower 1st gear you can start in high range, and work your way 1-2-3-4 that are synchronised.and don't have to touch the range gears.

9th gear gives enough low take off gear on road transport without bog down with pulling a load. And 8th gear gives you plenty enough field transport speed before it throws you out of your seat. I have cut a pretty decent smooth field in 8th gear where I had to also keep rpms up to do a clean cut and at times I had to drop down to 7th to have better control when bouncing gets a little to rough. I have a 2018 T6.180 6cyl. with 16x16 Electro Command also and they seem to be the same, and I don't particularly like trying to push that lever up to high range when I'm trying to get out of the way of traffic that might be coming up on me around a blind curve out of a field, that's when it makes sense to take off in the 9th gear in the high range and then I can toggle or run auto shift all the way up to 16th gear without any sweat of bog down.

Moving round bales, you can stay in high range coming and going from field to road and vice versa without lugging.

This is a very informative video. Great video!!!!

Great video, very informative! Your theory makes sense.

Good video I personally got a TN75. There actually is a diagram on the inside of my right fender wich shows exactly what you are explaining in this video.

Your right about the low gear in C range!

power command is just a god sent XD

I operate a T5.115 at my workplace. One thing I don't like is the steering wheel/display tilt has a small pedal between the clutch and the brake pedals.

You need to have good working gears equally spread out in all three ranges , its not a car its a tractor

have a tl90 dual command , having 1 st high so low is very handy when pulling off with a 2000 gallon slurry tanker

Deere had this on the 4430 quad range it was designed this way to prevent clutch slippage when pulling heavy loads and needing to upshift to get to faster speeds

yeah, every tractor, or vehicle in general for that matter tyhat has multiple ranges are going to work out this way...

it's so you can keep good gears no matter what range your in like I buckrake in M4 on a 24 speed 6640 but if I hit a big lump I can drop it in to M2 easily and still keep going but I've have to stop I had to change range

This goes right back to the Ford 5000 series 4th Low range slightly faster than 1st High Range. Which was 5th .

Fiat build this transmissions from the 70's. It was designed for the Fiat 80 series. Later on they used it for the 90 and 94 series. Basically the TN TL and the older 35 series are old fiatagri 90 series tractors. With a new blue coat. 😉

Yep, our TS100 is the same setup with the dual command... probably one of the reasons why I like to use it a lot due to the shifting for mowing and raking. We just got a TS6.130 with a 16x8... sadly, it isn't as nice as the 24x24 :( Massey has a similar gearing design with the Dyna-4s and 6s, especially with Ranges 2 and 3; the higher gears in range 2 somewhat match the lower gears in range 3 for better field operation. You can thank Jeff Reymond for me discovering your channel. I'll definitely be checking out your other vids.

Quite interesting, good video

On my dyna-4 Massey 5713SL i'm forced to work slower than i could sometimes unless i want to change ranges every other minute. Wouldn't have to if ranges overlapped a little and i just could stay in the higher range and only cycle between 4 powershifts. Then again, not overlapping is superior in transport. I guess the most important is to be aware of these differences and to know what you want before you buy a tractor. None of the tractors is perfect for everything.

I just sold a 2010 Claas Arion 510 because i bought it for repair and sell, had accident with radiator so full engine rebuild, it was the best tractor i have ever driven, leave the New Holland for dead, the reason i came here is because my next project when i buy it is a newish New Holland with FEL which broke in half, the tractor is sitting in a yard with the engine on the ground with the back half and everything else in front of the engine in pieces, I have not yet found out why.

Where can I get my T4.90 Newholland fixed. It's in DEF computer shut down.

Looking for a how to video on replacing the 4w-n-2w shifter arm on a boomer 40

I got a little TC35 and finding the gear for moving around the yard quickly Is kinda a pain. Field stuff is pretty decent but I suspect your theory about gearing is true.

The fergy 47 is mixed up also

a thief would have to go to school to steal that thing

I have a New Holland TL 100A tractor. My problem is----the tractor always starts off with a JERK. (and I don't mean the driver!!!!) It has the gears and range that you show, plus a clutch, plus a forward and reverse lever on the left of the steering wheel. I got the tractor used, and don't think this jerk-starting is normal. Could it be the type fluid I am using?? Is there another problem I don't know about?

Amigos me puede decir el manejo correcto de un tractor new Holland m 135 power shift

I have a 2009 T6010 when I put it in 4WD it makes noises, anyone know what could be the issue?

Hello.I changed the hydraulic filters to the new holland td5.115 tractor and now it does not work anymore.It works first.Do you have any idea why?

I see a 7710 in your shop. Care to give a video and review on that oldie but goodie?

Mein Traktor arbeitet nicht Geschwindigkeit (A) habe keine Ahnung. können Sie mir helfen

Tm 120 range command Ford newholland four wheel drive not working ,what could be the problem

any advice for my FNH 1997 7740 SLE,? - It is stuck in forward. the shuttle wont go back into neutral.

looking get answer why my New Holland T1510 wont move forward after getting warmed up and or move forward with load

I suppose this works on 17x17 electrocommand. Because on low group or what i would say in english has 8 gears. So would it not work the Sam as the 16x16 electrocommand. I can maybe try it on the ts135a tomorrow tho.

RR's do that . Options.

Which models are available with terralock functions??

Are you still a NH man, or are you switching to Massey??

error code f41 tm165 tractor?

Shut that thing off!! Can't hear you!