SEGWAY NINEBOT G30 MAX REAR MOTOR WHEEL BEARING REPLACE | NINEBOT G30 MAX ЗАМЕНА ПОДШИПНИКОВ

Рет қаралды 71,604

2 жыл бұрын

SEGWAY NINEBOT G30 MAX REAR MOTOR WHEEL BEARING REPLACE | SEGWAY NINEBOT G30 MAX ЗАМЕНА ЗАДНИХ ПОДШИПНИКОВ
#segwayninebot #segways #g30 #ninebotmax #ninebotg30max #bearing #bearingreplace #electricscooter #escooters #scooterrepair #ремонтэлектросамокатов #электросамокаты #самокат #самокаты
Как снять заднее колесо на Ninebot KickScooter Max / How to remove the rear wheel.
Ninebot Max G30 Scooter - Squeaking, grinding, noise rear wheel bearing replacement/upgrade.
Bearings: 6003 RS
Подшипники: 6003 RS
If you like it, please support by buying the EP at www.northboundsound.bandcamp.com
More music and info also at: northboundsound www.soundcloud.com/northboundsound

Пікірлер: 119

@Wavelover33 Жыл бұрын

Just in case anyone does this - when you take out the main motor hub don’t get your fingers in the gap that opens as your doing this. There are extremely strong magnets that will “suck” it back in and trap your ur fingers with a lot of force

@vfxcristi4no 5 ай бұрын

just had this happen to me, be careful lmao

@Wavelover33 4 ай бұрын

@@vfxcristi4noha! I had to get my wife to pry it open. Crazy force in there!

@AlonAbraham1 Жыл бұрын

Thank you very much for this video

@RMFUNTIK Жыл бұрын

you are welcome!

@phylosophersstoned43 2 жыл бұрын

awesome. watched this video in advance before i need to change one day

@RMFUNTIK 2 жыл бұрын

Glad it was helpful!

@truthseeker6804 Жыл бұрын

have you needed to change?

@phylosophersstoned43 Жыл бұрын

@@truthseeker6804 got hit by a car and the tire is always deflating so I might have to soon

@truthseeker6804 Жыл бұрын

@@phylosophersstoned43 what? sorry about that. hope you are ok?

@vidared93 11 ай бұрын

Excelente

@firasal-taie8267 2 жыл бұрын

Thanks

@RMFUNTIK 2 жыл бұрын

your Welcome

@afzalimustafa8400 Жыл бұрын

Super

@RMFUNTIK Жыл бұрын

Thank you

@fireemblemistrash75 4 ай бұрын

It is customary to have 3 liters of hard liquor when working on the later models of this scooter. You CANNOT disconnect the rear wheel as easily due to the brown yellow and blue cable being screwed, meaning now you have to remove the battery just to get enough room for a tool

@RMFUNTIK 4 ай бұрын

It's getting harder and harder to fix something...

@meowchin Жыл бұрын

What about the radial seals? Are there replacements available?

@RMFUNTIK Жыл бұрын

don't know, but you don't need to replace them, they are in good condition and you can grease them inside + the bearings have a good seal.

@andrews3902 5 ай бұрын

Great tutorial. Question - is it necessary to you use lithium grease?

@RMFUNTIK 5 ай бұрын

nop.. you can use any other grease for rubber bushings

@ionutpintea9775 3 ай бұрын

Great video! Was the scooter going like it was breaking or what was it that told you it was the bearings?

@RMFUNTIK 3 ай бұрын

client wanted to change them just for maintenance :) they where fine, but you know, scooter was had 4000km on it.

@semperfi69 Жыл бұрын

Hello Could you please tell me the size of the torx screws of the bottom plate that give access to battery, motherboard etc please? Thanks

@RMFUNTIK Жыл бұрын

i don't remember, a guess t10 with a hole. just buy your self a cheap set.. they cost like 5 dollars.

@ssilk Жыл бұрын

Hi! Super Anleitung! Frage: Was ist denn das für ein rotes Fett, was du da reinschmierst? Irgendwas spezielles, oder einfach nur "Fett"?

@RMFUNTIK Жыл бұрын

i don't speak german, but i understand, you can use any grease you like... i'm using this one because i have it at moment, u can use even wd40 for sliding the bearings and some silicon or lithium base grease for gasket

@firster8 Жыл бұрын

Etwas spät aber im Deutschen: Lithiumseifenfett

@marylinecourtemanche2782 7 ай бұрын

witch quit of tools needed for the bearing operation? ty

@RMFUNTIK 7 ай бұрын

all shown in the video.

@alejandropena3594 Жыл бұрын

Hello friend, do you know what are the measurements of the front wheel bearings of the Segway f40e scooter? Thanks 👍

@RMFUNTIK Жыл бұрын

sorry no, take it apart and read whats on bearing written, there should be a numer 6001/6002 or 6003 rs

@chinolopez572 Жыл бұрын

My scooter do not run over that 17 miles. What do you think is wrong with it.? I replaced the trouble speed already

@RMFUNTIK Жыл бұрын

needs diagnosis

@easytitak2225 2 жыл бұрын

hey my back tire somehow blocked and it’s not start now, kind jammed, its rotate but stucking… do you think this is the same problem

@RMFUNTIK 2 жыл бұрын

i guess it's electronics.

@reflektion1791 Жыл бұрын

Can a second external battery be connected to the front of the ninebot e45d? So I had one internal and two external batteries? how can i connect together ?

@RMFUNTIK Жыл бұрын

Yes if you can do a custom firmware to unlock charging while driving.

@Alex_Verso Жыл бұрын

А можно ли достать-купить оригинальное 9 мотор колесо (более скоростное) и поставить за место 6 , и прошить что он ехал под 40 км в час?

@RMFUNTIK Жыл бұрын

незнаю

@ivanmeister195 Жыл бұрын

By a New Wheel with Motor its Easier !!!!!

@badlands5527 Жыл бұрын

This is way cheaper

@TheArachnoBot 11 ай бұрын

A bearing costs only a couple euros

@mrbeanz6451 Жыл бұрын

RS v RZ BEARINGS does it make a difference? One on my scooter which is a copy of this have 6202RZ bearings

@RMFUNTIK Жыл бұрын

RZ: The bearing side has a low friction seal lined with steel plate synthetic rubber (non-contact type); RS: The bearing side has a contact seal lined with synthetic rubber or polyurethane (contact type)

@mrbeanz6451 Жыл бұрын

@@RMFUNTIK I have brought ZZ bearings to replace the RZ as the RZ Dont appear to be widely available as the RS/ RZ ...hopefully they will last

@RMFUNTIK Жыл бұрын

RZ bearings are not sealed (water, dust proof)..

@AlexPlay98 Жыл бұрын

А герметиком разве не нужно наносить на крышку аккумулятора,когда обратно ставишь?

@RMFUNTIK Жыл бұрын

зависит, от того будешь ли ты ездить в мокрую погоду или нет, у самоката рейтинг Ip54. + там штатная прослойка хорошая.

@jndelarue3832 Жыл бұрын

👍 juste le joint d'étanchéité à la pâte entre les 2 parti qui n'a pas été fait..

@RMFUNTIK Жыл бұрын

the is no seal in original.

@tom9506 Жыл бұрын

hello friend I got an important question, from minute 14:35 onwards, is it not necessary to apply sealant such as Hylomar to the edges of the cap so that dirt does not get into the housing? I read in a forum that you should definitely do this. Do I have to? :) Thx for making this video!

@RMFUNTIK Жыл бұрын

yes you can put some sealant it won't be bad :) but the main water and dirt leak is from bad bearing seal

@jeffbrown8051 9 ай бұрын

I want to so this nyself. Is it diffucult to make the bearing press?

@RMFUNTIK 9 ай бұрын

you can hammer it, find a socket with the same diamentr as the outer ring of the bearing.. nop.. just some socket heads and threaded steel pin

@anshulkhatri6231 2 жыл бұрын

Hi, my back tire is kind off jammed and the scooter died while i was riding it, but there was one cell battery left. What do you think is the issue ? Btw, nice video.

@RMFUNTIK 2 жыл бұрын

what do you mean by off jammed?

@anshulkhatri6231 2 жыл бұрын

Like it rotates but with some thing like its in gear.... ? Or stuck to it .

@RMFUNTIK 2 жыл бұрын

@@anshulkhatri6231 hmmm... maybe something wrong with your motherboard? never seen that trouble with g30..

@anshulkhatri6231 2 жыл бұрын

Weird part is, there was battery left ... And stopped and then the tire is locked ... Not completely but it move with more effort. And the scooter does not turn on either. Also, I put it on charge last night thinking that the battery was down, but it did not turn on while i put it on charge. I checked today morning and its still not turning on. So, if its motherboard then just replace it? I am in Canada... Do you have any recommendations?

@RMFUNTIK 2 жыл бұрын

@@anshulkhatri6231 nope it not motherboard, guess it's BMS, check the voltage on the battery pack it should be 37-42v

@adriancovi Жыл бұрын

Hi friend, thanks for the nice video! I need some support that I'm looking for a long time, hopefully you can help me. Do you know the correct code of each hall sensor inside the motor? I'm struggling to find it and I'm having problems to run my G30 due to that. It would be very very helpful. I almost could read it at 5'02" in 4k resolution...

@RMFUNTIK Жыл бұрын

www.falconpev.com.sg/collections/spare-parts/products/motor-hall-sensor-single-piece try here

@adriancovi Жыл бұрын

@@RMFUNTIK Thank you very much for replying me, I'll give a try with the sensors in the link! But my concern still is that it seems that in the G30 motor, the central Hall Sensor is different than the other two. That means two types of hall sensor and my guess is that this is my problem now, I'm using the same Hall sensor in the all three positions...

@RMFUNTIK Жыл бұрын

@@adriancovi www.scooterhacking.org/forum/viewtopic.php?t=174

@Alex_Verso Жыл бұрын

Скажите а такой самокат как на видео с 6м моторколесом вы прошиваете? И сколько из него можно выжать км в час?

@RMFUNTIK Жыл бұрын

если не заблокирован, то да.

@DimaVolcok2255 Жыл бұрын

xiaodash 36км на ровной а если горка то под 45

@user-GS999 4 ай бұрын

чувачек если не наживил то так болты не закручивают может выйти осечка а солидола не жалеешь опыт слабенький но молодец что собрал

@RMFUNTIK 4 ай бұрын

если у тебя руки кривые, то да, возможно! молодец, что посмотрел как делают профи!

@user-GS999 4 ай бұрын

Если одел перчатки то это не знак профи а проблемка

@selcukkonar1301 11 ай бұрын

Hi super video👍 meine Frage woran hast du gemerkt das die lager im hinterrad kaputt sind? Meiner macht nimmlich Geräusche und fährt ganz schwer auf 6 kmh und das wars

@RMFUNTIK 11 ай бұрын

well, the scooter was about to hit 2000km, so i did change them, they where normal, but i decide to change them, because front bearings was kaput.

@selcukkonar1301 11 ай бұрын

@@RMFUNTIK OK danke für die Info 👍

@RMFUNTIK 11 ай бұрын

@@selcukkonar1301 bitte schön

@timborgmeier2862 5 ай бұрын

Ich hab es so ähnlich nach dem Lagerwechsel macht meiner Geräusche und kommt nur auf 10kmh und weiß nicht woran es liegt. Was war es bei dir?

@timborgmeier2862 5 ай бұрын

Oder hat jemand ne Idee was ich falsch gemacht habe

@Thevariablegamer Жыл бұрын

Would these bearing work the the Segway f30?

@Thevariablegamer Жыл бұрын

And is the WD-40 lithium grease okay to use?

@RMFUNTIK Жыл бұрын

don't know f30, never been in my repair shop

@RMFUNTIK Жыл бұрын

@@Thevariablegamer wd40 is not lithium grease..

@Thevariablegamer Жыл бұрын

No wd40 makes lithium grease

@Thevariablegamer Жыл бұрын

Would it be fine to use it?

@CALIFORNIA650. 10 ай бұрын

Can you remove the shaft from the motor?

@RMFUNTIK 10 ай бұрын

With a press, I guess yes.

@GARIK-nx9mp3tf3y Жыл бұрын

какой нужен подшипник на самокат digma allroad max

@RMFUNTIK Жыл бұрын

сними крышку, там будет написано на нем.

@GARIK-nx9mp3tf3y Жыл бұрын

@@RMFUNTIK ясно спасибо

@pixelfullhd 2 жыл бұрын

А почему именно литиевую смазку использовали?

@RMFUNTIK 2 жыл бұрын

ты можешь просто wd смазать.. разницы нет.. я просто набил ее туда, чтобы вода не проникала.

@pixelfullhd 2 жыл бұрын

@@RMFUNTIK понял, спасибо

@pixelfullhd 2 жыл бұрын

@@RMFUNTIK а подшипники оба 6003?

@RMFUNTIK 2 жыл бұрын

@@pixelfullhd зад да.

@FixLife 11 ай бұрын

кто знает где заказать крышку моторколеса? и желательно с гравировкой 250ватт или менее, ну вы поняли))

@FixLife 11 ай бұрын

kzfaq.info/get/bejne/arl-ZLCSlbbTo6s.html

@RMFUNTIK 11 ай бұрын

отдельно вроде как не продается.

@jmginthent651 Жыл бұрын

Off topic but does anyone know how to remove the yellow stripes from the rims ? I have tried a heat gun and also acetone but they seem to be painted / stuck on pretty good ? id like to jiust have the matt black rims with no colour ...

@RMFUNTIK Жыл бұрын

they are painted..

@ivanbilandzic6571 4 ай бұрын

Hau meni km is on dis motor?

@RMFUNTIK 4 ай бұрын

1000

@Alex_Verso Жыл бұрын

14:36 хорошо видно что с завода нанесён голубой герметик, (для гидроизаляции мотора) при разборе мотора вы его повредили! И при сборки не убрали заводской герметик и не нанесли новый! А при езде в дождь или снег - слякоть как раз на заднее мотор-колесо летит вся грязь и вода! Это же явный косяк при сборе мотора? Или я дурак просто.....

@RMFUNTIK Жыл бұрын

Где ты там увидел голубой герметик? Нету там герметика вообще. И основная причина воды в мотор, хреновые подшипники... А не крышка мотора. Я уже в 200 раз всем говорю, знаешь сколько моторов я уже перебрал? Не один мотор не был ржавый из-за крышки, только из-за того что подшипники оригинальнфе были дерьмовые.