Seller Sold Me The WORST Quad I Have Seen (I Regret Buying This)

Рет қаралды 192,587

Жыл бұрын

I fix up a Honda 400ex big bore quad in one of the worst conditions have seen. #Honda, #BAD, #BigBore,
►SUBSCRIBE: / @2vintage
►MY SECOND CHANNEL: • New Polaris ATV Snow P...
► ADD ME ON ALL SOCIAL MEDIA ◄
► FACEBOOK: / 2vintageyoutube
► INSTAGRAM: 2_vintage_ / 2_vintage_
► SNAPCHAT the2vintage
► EMAIL FOR BUSINESS INQUIRIES ONLY: 2vintagetooo@gmail.com
Thanks for watching and subscribing!
New videos every week!
The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. 2vintage( Joe Weber, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL 2vintage( Joe Weber) CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.
2vintage (Joe Weber) makes no representation about the sufficiency of any safety precautions and equipment used in this video.

Пікірлер: 518

@jonathanjo4273 Жыл бұрын

This bike was completely junk

@brandonbellacima66 Жыл бұрын

You should really invest in buying a press for doing bearings. ever since i bought mine its a game changer. makes life so much easier

@kenjohnson5498 Жыл бұрын

The blooper on the pipe flange was awesome, the fact you leave your mistakes and even point them out in the videos shows your integrity.

@Leon-hg6ih Жыл бұрын

I'll give you your money back for it

@jeeperzcreeperzz Жыл бұрын

The question is what are you going to do with all of these amazing machines that you are hoarding and never ride except for 1 video. Its kinda sad that all of these dont get used when Someone else could be enjoying them

@Timbo5553 Жыл бұрын

Get yourself a decent 1/2 impact wrench always see you struggling with most stuff save yourself the time and effort 🤷🏾‍♂️

@fj5gtx770 Жыл бұрын

I think welding on a standard plain steel nut will work much better than trying to get a nylon lock nut.

@slipknotfreak744 Жыл бұрын

When tightening the nuts on the axel you used a channel lock. Flip your channel lock upside down so that you’re tightening towards the bottom of the tool not the top. The teeth bite in the opposite direction so it will hold a little better. Same with a pipe wrench.

@caperperformance4849 Жыл бұрын

Theres sepecial wrenches and torque specs for the rear axle. Its going go come loose with what you did

@leekarpinski4038 Жыл бұрын

Yes yes yes

@hoosierway Жыл бұрын

This quad is a true testiment to what you do for the "toy" community. You never gave up (except the exhaust bolt) on anything that reared its ugly head. This is why your fans love you. Fantastic job on this. I wouldn't mind having this quad after you have it finished.

@jesterr7133 Жыл бұрын

Lol. I had a 150cc Coolster ATV that I was working on for a friend of mine. It came in for a carb cleaning, but it ended up with a new battery, carb, starter, starter solenoid, shift knob, and battery cable by the time it was done. Everything but the solenoid was trash. I just replaced the solenoid so he wouldn't have to worry about it. I ended up having almost three months by the time I waited on parts and did all of the electrical troubleshooting. Sometimes these things just snowball.

@jessie8143 Жыл бұрын

When you're checking ring gap, use the piston to push the ring into the cylinder so you can assure that the ring is sitting evenly in the cylinder, otherwise you can get a false reading with the feeler gauge.

@Tyler-jy3sn Жыл бұрын

A good tip for getting stuck bolts out is to place a punch or a screwdriver on the end of the bolt (or a nut) and give it two or three hard taps with a hammer, it works better than what you would think

@boebradley867 Жыл бұрын

Come on man! I have bought them in parts with motor, no motor, sitting for 20 years and you

@ezio8591 Жыл бұрын

Everything is possible if you're willing to roll up your sleeves, work hard, sweat and bleed for your goals and always be willing to learn, this is proof, all youngins take note. Job well done

@roryk.3568 Жыл бұрын

I'm thinking the back fire might be a lean topend with that main jet. Nice job, I had one worse condition, hard to believe. Yours fired same as mine, about the 5th crank. Haven't touched the carb yet. Little lean, colder weather does that. Poppy just like yours. 👍

@jakenoel4659 Жыл бұрын

11:15

@jamesbeckwith780 Жыл бұрын

Carbs lean stock 400 jetting for a 440 kits to lean. Bigger pilot the a/f screw won’t have to be turned out at 3 1/2 turns bigger main will help with back firing when off the throttle. Good job saving that thing. Great vid.

@arcticmsrock Жыл бұрын

These are 20 years old now. Is there a market for collectors on these? With as much work as you had done should have just powdercoated frame when you had it all apart and really brought it back to life.