Setting up a Home On-Tap Carbonation System -Complete and Unabridged

Рет қаралды 125,531

Күн бұрын

PSA: Doing any of these steps incorrectly or with the wrong parts could result in a horrible flooding of your house- follow the instructions at your own risk.
This is a super long video going into setting up seltzer on tap in excruciating detail.
0:00:00 Introduction and sources
0:00:36 The carbonator
0:02:24 Never run pump dry
0:02:44 Water filters
0:03:44 Carbonator parts close-up
0:04:31 No copper or brass!
0:05:55 Flare fittings
0:07:38 Don't use Teflon with flare
0:08:11 Notes on CO2 regulators soda vs. beer
*NOTE: at 10:11 I mention the CGA130, I meant to sat CGA320*
0:10:35 CO2 Tanks
0:11:51 Hoses to buy --Don't use PVC!
0:13:28 Hose discussion becomes rant
0:13:51 Hose clamps --Oetiker clamps
0:15:31 Removing an Oetiker clamp
0:16:02 Seltzer taps --how they work
0:18:34 Tower-style chrome valve
0:19:43 Cold plates
0:20:46 Importance of using 2 cold-plate circuits
0:22:39 Need a condensate pump for melt water
0:23:27 Going under the sink
0:23:38 Use 1/4 turn valves
0:23:53 Changing the water filter
0:28:20 Purging the air from the filter
0:30:26 Purging the carbonator. Important!
0:32:22 Turning on the gas and not getting fooled by your gauge.
0:35:18 Filling the carbonator with pure CO2
0:36:28 Plugging in the carbonator
0:38:22 First glass of seltzer
Sources:
markpowers-and-company.com/en/
foxxequipment.com/
www.mcmaster.com/
Parts list from Mark Powers with prices as of May 2020 (ask for Tim). I’d get extras of the cheap fittings. Trust me. Amount of hose will depend on your install. Try to keep the length of hose AFTER your cold plate as short as possible.
QTY Item PN Price
1 McCann Big Mac Carbonator E400397 $538 new $250 refurb
or
1 Little Mac (small version of above) 43-6002 $417
1 8x12 inch 3 circuit cold plate 8x12-3 $112 (special order)
(should come with 5/16 flare to ¼ hose adapters) Or
1 8x12 inch 2 circuit cold plate 8x12-2 $78
1 160 PSI TapRite Regulator 5741-PMHP $58
1 Cage Guard 18-0198 $2.27
2 20 Pound CO2 Tanks CO2-BLKH
1 CO2 Tank Washer CO2-27 $0.09
~30 Arrow Bev-Seal Hose 175-04500-00 $0.26/ft
~15 12.3mm Oetiker Clamps 12.3-706R $0.16
3 ¼ Flare swivel nut 01-0222 $0.50
3 ¼ stem for ¼ flare 01-0221 $0.77
3 White washer for ¼ flare W-20 $0.07
1 3/8 Flare swivel nut 01-0232 $0.79
1 ¼ stem for 3/8 flare 01-0231 $0.58
1 3/8 flare cap 01-0212/01
2 Black 3/8 flare washers NY-45-6 $0.11
1 Becker hand seltzer valve 20-2231-90 $39
Or, from Foxx Equipment
1 Ibis 1-Faucet Tower 12C03-208
Optional:
1 Red Handled Oetiker Pliers 1099-RED $37
1 Tubing Cutter 23680 $16
Or
1 Pocket tubing snip 100-008 $9
You will also need a water filter, condensate pump, and an ice box or ice machine as well as some random parts from your local big box store.

Пікірлер: 333

@MrBTOdell 3 жыл бұрын

This is the kind of content that KZfaq was made for.

@PatrickSalisMEDIA 21 күн бұрын

YOU DID AN AMAZING TUTORIAL. The information provided and your "How To" demonstration is unmatched... THANK YOU.

@zapsnyder 4 ай бұрын

This is exactly what i was looking for. No oversimplification, no details glossed over, just raw instruction. Thank you so much for this.

@michaelvanbogaert7888 3 жыл бұрын

YES! The pinnacle of custom meets practical! I've been trying to piece together a durable system for hours and this answered all my questions in a fraction of that. Thank you!

@linguistisch 3 жыл бұрын

I can't begin to tell you how helpful this video has been. I've read up on similar projects and had a good idea, but all of your small tips and experience are invaluable.

@robeckel4965 9 ай бұрын

I love it when people on KZfaq actually know what they're talking about. Thank you! This is gold.

@TechVolleyball 2 жыл бұрын

I’ve had to come back to this video several times. He explains everything perfect. You’ve saved me many service calls. Thanks dude

@GregorHalenda-Saku-Moto 4 жыл бұрын

I have been enamored of your system ever since that party at your apartment in 08 - I think it's finally time. Thanks man.

@SooperToober Жыл бұрын

You are the Seltzer Master Dave! Wow! So thorough and brilliant- thanks for sharing your experience and knowledge so freely

@mikepondiscio9916 3 жыл бұрын

This is a great video with thorough information. Your experience shows through! You have saved me a LOT of money and wasted time building this by trial and error. THANK YOU!!!

@KiyoshiProductions 3 жыл бұрын

man this helps so much, I was given an older coke drop in fountain dispenser but i was missing quite a few parts, this really helped me look in the right direction for fixing it back up again! thanks!

@user-vn3ml7xr2x 9 ай бұрын

Without a doubt, this is the best video about soda water out there. Super detailed, lots of helpful tips, and with a level of enthusiasm that keeps everything entertaining. Thank you!

@chefdhorrocks 3 жыл бұрын

Thank you David for this video. I followed your instructions and now have a seltzer tap for our product development lab. We've been using canned water for years, easily spending $100 a week on cans at times. With this, we'll save money, reduce waste and be able plus up the carb levels for superior products.

@justinherman9443 4 жыл бұрын

Bev-Seal Hose beats the pants off of any vinyl hose I have ever owned. Thank you for showing me this. It just came in the mail today and WOW without a doubt, an upgrade.

@grahammoore5658 2 жыл бұрын

Hi Justin, where did you source your hose from? Having some trouble finding it here in Canada, or even places shipping it here. Any help would be appreciated, thanks.

@justinherman9443 2 жыл бұрын

@@grahammoore5658 I got mine from Mark powers company. markpowers-and-company.com/en/ RAIDED BEV-SEAL ULTRA BARRIER HOSE, .265 ID X .420 OD, NSF, 500' ROLL

@grahammoore5658 2 жыл бұрын

@@justinherman9443 Thank you.

@fubar3571 3 жыл бұрын

Thank you so much for the detailed walkthrough, Dave! I completed my setup after watching your video many times. We are now getting ice cold super sharp carbonation on demand at all times, what a dream! Mark Powers seems to be on a hiatus, so I used Soda Dispenser Depot for all parts - one thing the video didn't list is the carbonator procon pump has a 3 1/4" flare with a 1/4" barbed fitting for tubing. Also note you can buy a 3 1/4" cap from them (don't forget the washer) for the extra water outlet. I ended up using a cooler bag with large Cooler Shock ice packs under my sink for the cold plate and it's working like a charm, and I don't have to worry about drainage, just the work of swapping ice packs every day or two. As a final addition I bought a krome dispense C503 tower from Soda Dispenser Depot as well, and drilled my sink for it. Thanks again for helping me put this thing together.

@cheffanxx 4 жыл бұрын

I've heard you talk about this on the podcast at least 100 times and usually get lost. This video is great

@dyardsale5475 2 жыл бұрын

What a great video. Much more complex than the setup I am building, but still wanted to see Dave's.

2 жыл бұрын

What a great video. It was so helpful. These videos need to be recommended by YT.

@kegmannet 2 жыл бұрын

Fantastic job Dave. Great sequence on how to prime the system.

@yevmeister8552 3 жыл бұрын

Thank you, i just picked that darn thing from the junkyard for $2 dollars. I have been home brewing for over 15 years . Excited to test out this thingy

@paulbunyun4479 2 жыл бұрын

lol, for 2.00 in a junk yard

@b-gill9224 3 жыл бұрын

This video is wonderful. Thank you so much for putting this together. You've inspired me to do my own!

@EnergeticWaves 3 ай бұрын

watched this several times, making notes now finally, but this is the best video with regard to setting this stuff up that I have seen yet.

@lordratner 4 жыл бұрын

Thank you! This is incredibly helpful. Hope you're working on your next crazy idea. My Spinzall needs friends.

@randomeer7831 2 жыл бұрын

You earned my subscription, and I wish you the best of luck with your channel, and the best wishes for this new year! Lovin your vid’s!

@Geigenbert 4 жыл бұрын

I just love you Dave!

@scottettinger9231 2 жыл бұрын

Just finished my seltzer system and it works great! I wouldn't have had the ambition without this step-by-step well detailed video. instead of the cold plate, I bought a $43 6-can capacity mini fridge & some 1/4" stainless steel tubing formed into a coil. I drilled 2 holes in the side and used Great Stuff to seal it up after the tubes were fed through. We'll see how it works in the summer. Thanks Dave!

@sdcnzl 2 жыл бұрын

How has this setup been working for you?

@scottettinger9231 2 жыл бұрын

@@sdcnzl not as well as I hoped. The carbonation was weaker than I wanted, not as cold as I hoped, and I had the wrong dispenser that gave metallic taste after a while. I'm almost done doing it a different way. Split the pu.p and holding tank on the carbonator. Putting the tank in my fridge with an appropriate dispenser. Now the seltzer doesn't have to travel 30 feet to my dispenser. Hope it works better

@Bottleworksnet Жыл бұрын

Those super mini "fridges" don't use refrigerant and a compressor. They can't cool like a real fridge.

@Badge124 3 жыл бұрын

Awesome video! Very detailed and informative. Thank you!

@ABWSKITCHEN 3 жыл бұрын

I made my first 10 months ago, I learned basically by myself, your video is great, I will definitely make a similar video for my cooking channel.

@finieclimber Жыл бұрын

Great tutorial will be using it as my guide shortly. I was looking for that belch at the end to sell the carbonation.

@pwphoenix02 Жыл бұрын

Awesome video, looking into doing my first system in the next month or so, already got a big boy.

@beefsupreme64 Жыл бұрын

Easily the most informative video on this topic

@2010mistersoftee 3 жыл бұрын

Dave, Thank you, your system work perfect!!

@wh865 Жыл бұрын

Excellent presentation and knowledge!!! Thank you!!!!

@janitziolazcano2226 3 жыл бұрын

Wonderful video, thank you so much for creating it.

@charlescates6803 3 жыл бұрын

This is one of the best instructional videos I've ever watched. I'll definitely set up one of these. Thanks!

@EnergeticWaves 3 ай бұрын

Been a month but am minutes away from starting this system based on your video!

@tyuade3456 4 жыл бұрын

You the man, Dave!

@gargfunk 2 жыл бұрын

Really good video. Explains everything I had questions about. In figuring out how to put a complete system together, I have a few questions: 1) Any reason not to put the McCann in a mini fridge and skip the cold plate? 2) If an Ibis 1-Faucet Tower is not an option, what does the Becker hand valve install into? I see a selection of Draft Beer Towers but nothing to tell me what the Becker is compatible with, or how to tell that.

@FrustratedBaboon 3 жыл бұрын

Super video and excellent advice for just CO2 drink that pleases us.

@jennischmidt6405 3 жыл бұрын

This was an amazing tutorial, thanks for the info dump! I’d love to get a tour of your kitchen it looks like you’ve got an amazing setup!

@jeromepanal6962 Жыл бұрын

SUPER BIG help... More power to you sir

@marcusphilipus6896 Жыл бұрын

Thank you very much. You are a Guru ! I have learned so much from this video it's not only science but it's an art lol thank you again . Now i just have to look up the links on the parts ill need to replace specially the hose (although it says it's food grade and i don't have any smell or aftertaste, but I'm getting the one you recommended

@wheelparty 10 ай бұрын

There are a quite a few ways to carbonate water at home, but this using a compressor is by far the easiest I've found because you don't have to shake the water to solubilize the CO2.

@anthonydellaragione81 5 ай бұрын

You video is great so much more knowledge then the rest !

@EnergeticWaves 11 ай бұрын

amazing the creativity of people!

@Subgunman Жыл бұрын

I have always dealt with Foxx for all of my needs. I was doing all types of repairs on soda, and beer systems and still purchase any supplies I need for my personal systems since changing jobs many years ago. Before I moved to he EU I ordered the 220volt motor and sensor for this same McCans carbonator. Works great, too bad Coke and like products post mix syrups are too expensive in the EU, main reason is that they only use cane sugar in syrups. High fructose corn syrups are illegal here. They still use the Stainless steel kegs here for syrups. Thank goodness I have all the fittings needed. That hose used for carbonated beverages (double wall hose) must not be exposed to UV light. It will degrade and could rupture creating a real mess. I prefer the double sided clamps, they make for a better seal. I would recommend adding a stainless steel shutoff valve on the output of the carbonator should a line break. It’s also good to shut off the electric, CO2 and water if you are going out of town. Better safe than sorry, nothing worse than coming home to a flooded kitchen. As for those quarter turn valves, you need to work them a few times every three months. They will freeze up with mineral buildups (yes even with soft water they will clog ) and will become inoperative or extremely hard to operate. Interesting build up of a water manifold under his sink. Here in the EU plumbing supply houses have manifolds with up to 8 ports. Only issue is they use 1/2” British Straight Thread compared to our 1/2” tapered thread.

@2DButt 2 жыл бұрын

You're a legend Dave

@justinherman9443 4 жыл бұрын

Dave is awesome.

@Mar-sr5uf Жыл бұрын

FANTASTIC VIDEO!

@lorenzo42p 3 жыл бұрын

love this guy, great video, thank you. I learned a few things I haven't seen elsewhere on the internet. I was tempted to buy a big mac carbonator, but I wanted something I could fit the tank right in my kitchen fridge. I got a 1.5 gallon 6 liter torpedo soda keg. I got a special lid to put on the keg which has the water inlet and the float and spray nozzle. my ro filtered water is only 35 psi, so I have a diaphragm booster pump ordered which should fix that problem for me, cuz I want high carbonation. I was tempted to get a cold plate, but much better to just put the whole keg right in the fridge. I'm still looking for a soda tap/dispenser valve. difficult to find one I like. I'd love to have a proper soda fountain dispenser, but no idea how to connect to one of those heads without buying the whole fountain, which is far outside my soda budget.

@TommyShlong 3 жыл бұрын

Pete - Yours sounds like a good idea. What brand and model booster pump did you buy and from what site? Also, what psi are you looking to use?

@moonolyth 3 жыл бұрын

OK, sir yes indeed I promise I will use that particular hose, wheres my Momy help! All kidding aside, great info !!! just found one of these machines on Facebook for $100. after viewing your vid, you are the man! I need not look any further, but I'll probably have to go with the mobile party outfit as there is more cost than I can justify at the moment... good to know how to do it right though and no wasted time being educated!

@kylebeckstrom3867 3 жыл бұрын

Awesome video bro thank you!!

@karsyz 7 күн бұрын

Solid vid and super helpful! Thanks!

@sheepraider2196 Жыл бұрын

Really nice video my friend :) I learned a lot!

@chris415-a 10 ай бұрын

very informative, thank you for making

@Dominikmj 3 жыл бұрын

Absolutely awesome! However - it would be amazing to get some information how to carbonate (large volumes) of flavored sodas (not a fan of post-mixing) - in a bar setting...

@Depression2010 3 жыл бұрын

Great Video Wonderful Job! A person would really need or want to have this at home before it is economically feasible. My wife is drinking about a case a month at $15. Even if she drank 2 cases, it would take some serious consideration. It is not like it is free or no work, once you have the setup. How many liters or gallons of carbonated water can you get from 20# CO2?

@gregtruchot8826 8 ай бұрын

Awesome! Great video!

@ivanpap634 3 жыл бұрын

Great video!

@dfjpr Жыл бұрын

very impressed, that's amazing

@2010mistersoftee 3 жыл бұрын

Would like to see and hear some more information about syrup pumps and their hook ups

@wsalizb12 3 жыл бұрын

This is brilliant

@leeh0795 3 жыл бұрын

Dave put this all in a box and sell it.

@paulbunyun4479 2 жыл бұрын

go to restaurant dumpster and find one

@stewartbruce2409 3 жыл бұрын

Dear Dave, I totally enjoyed your video on the operation on the E400397, as I found one in the trash on last nights walk. Plugged it in and was pumping water out of tank. I don't drink carbonated beverages, but thought I could re purpose it for. something. Any ideas? Thank you for an excellent job explaining what my new find is used for. All the best from New Rochelle N.Y.

@danielalworth7187 Жыл бұрын

Thanks for making this!!! youre a riot too

@midfutballr 3 жыл бұрын

Thanks for posting

@mattronan2746 3 жыл бұрын

Would love to see a similar video that cuts out the Big Mac and the cold plate and that carbonates directly into a keg or just a plastic bottle.

@seanmaxwell5231 Жыл бұрын

That man loves the Seltzer

@grahammoore5658 2 жыл бұрын

Hi Dave, Great video! I have everything together but can not seem to find a PE core hose. Any recommendations on where I can source the hose from? Thanks.

@janettelanuiki 2 жыл бұрын

Ok professor(journeyman plumber here) I loved the video but wanted to clear up a psig (water pressure to the home) thing.We install PRV’s ( pressure regulator valves mostly brass )valves all the time! They regulate those whom are getting high water pressure100+lbs down under a “normal range” of pressure.Watts PRV’s are 3/4”to 2” in size(most are on 1” water mains for residential applications) The pressure regulator are at 90lbs on the high end to 45lbs on the low end.

@Bottleworksnet Жыл бұрын

You completely missed that he said. Go back and try again, journeyman...

@seanmacdonald8476 2 жыл бұрын

Thanks for the vid! I will be following a lot of your advice on my first home system here shortly. It appears Mark Powers is out of business, any new recs besides foxx? Also out of curiousity.. what keeps the lines from freezing inside your ice maker? And even the loops in the cold plate itself? I'm thinking of just isolating the tank in a fridge for my setup but still curious of the cold plate thanks!

@richmather8436 2 жыл бұрын

Hey Dave, this is great! Do you have any thoughts on using a different flow control faucet like a Perlick 630ss?

@kidhack4141 9 ай бұрын

This is awesome. I'm not sure I have the patience.

@thelordofspyro 3 жыл бұрын

Oh, i like this dude... And his carbonator XD

@rsprsp2404 2 жыл бұрын

Great video David. I agree with the person who recommended you package all the products together and sell it as a package deal on say Amazon. I would buy it right now, as I personally like buying new versus risking buying someone's old used possibly poorly maintained restaurant equipment that may fail and flood the house down the road. I have a sink/drain along with an ice maker and Culligan's Aquasential tankless RO drinking water filtration system that provides over 600 gallons per day of RO water at an outlet flow rate of 0.42 gpm with a recovery rating of 69.6%. Specs say the unit has a daily production rate of 757.2 gallons per day. I would very much like to feed your recommended carbonation setup with filtered water from this system into a cold plate in bottom of icemaker to chill the water and then feed it into the carbonator. What do you think?

@airlar4857 Жыл бұрын

Seltzer perfection! 🏆

@gustavocarranza369 Жыл бұрын

Great video! It has been so helpful. I have a question, hope you can help me. What’s the “efficiency” of that system? I mean how many liters of water you can carbonate from each lb of CO2. Thank you!!!

@pumpkingod Жыл бұрын

Awesome video, but if I wanted to combine the faucets for chilled water and carbonated water, what type should I get? Or perhaps also hot water, since I also have an undersink boiler? You mentioned that the valve type was important for carbonated water, and of course I’d need the fittings to all be stainless

@nicoladellino8124 3 жыл бұрын

Nice video bro, tnx.

@bens3883 2 жыл бұрын

Hi Dave, very informative video. Great job! Quick question, maybe with a long answer. What would be the roadblocks I would run into putting the whole system in my utility room and just running the carbonated water line to my kitchen. It’s about 30 ft.

@chrishundt8839 2 жыл бұрын

I did something like this, with the system in my basement running up to my kitchen. The obvious thing happens: the water sitting in the house after the cold plate gets warm and foams coming out (losing carbonation). After that water has been dispensed the water that was sitting in the cold plate is better, although it is still slightly warmed from passing through the hose on the way. It works fine for me, I either throw away the room-temperature water or let it mix with the cold water that follows, depending on how cold/fizzy I want my drink. With 30 feet of 1/4-inch hose you will get about 10oz of warm water each time you dispense. You can insulate the hose if you want the water in the hose to warm up slower.

@waituntilthebeep 3 жыл бұрын

I did this exact same thing and put a bar tap on the counter with all my mixes. I am on a well so I have an RO with 6 gallons worth of storage tanks. Killer replacement for the old sodastream rig. If you buy your tank, take it tona fire extinguisher shop for refills... you get to keep your expensive tank and don't get some beat to shit rental

@paulbunyun4479 2 жыл бұрын

if you have RO water your hosed..you CAN'T carbonate RO water..fire extinguisher shop..lol i get it but is that food grade..the tank they used to fill those extinguishers are probably filthy on the inside loaded with crappy oil ect

@divingfe 18 күн бұрын

@@paulbunyun4479 OF COURSE you can use R/O H2O !!. My setup adds back some minerals, after the R/O filtration. I then boil the water to de-aerate it (holds more CO2 that way. let it cool, bottle it, get it slushy-cold in the fridge, Then I CO2 infuse it at about 60psi, while agitating the bottle until no more CO2 will go into the bottle. Then I re-frigerate it until I want to use it. All works like a no-sweat system, and very inexpensive. P.S. I suspect that ALL CO@ is food grade. That way, all the suppliers don't have to keep track of separate systems.

@Joncon00 3 жыл бұрын

Thanks for this great info. I am stuck not where I just turned on the water supply to the setup and the vent on the backflow preventer is pouring water out. There is no C02 and the tank was empty. I assume the procon pump allows water to pass without being on and that the issue is with the backflow preventer itself?

@paulbunyun4479 2 жыл бұрын

correct replace it

@excelsiorfarms7598 2 жыл бұрын

Dave... I know it is a lot of holes in the side of a mini fridge for hose and electric, but can't I install this inside the fridge and forget the chilling plate? Be quieter too?

@cobalt01snet 2 жыл бұрын

Dave A: what is the correct water pressure in the bigmac carbonator, I have a 8 port soda system at home but it seems to have a head on the soda the seem to eat up the carbonation, the only think I can think of is carbonator water pressure to high, I have a water regulator after the filter before the corroborator, it splits to the corroborator and the water port of the soda dispenser, thank you for reading, Tj

@danieltrojahn5749 2 жыл бұрын

Hello, thanks for this video., I have one quick question. My co2 tank has 3 guages on it, one goes to the carbonater and one goes to the pumps. what should each of those read. One of them is at 100 psi and it looks like the other is at zero, or over 100. there is also a guage on the ;pumps that is on 18. any help is appreciated

@mikekortbawi3422 Жыл бұрын

Thanks for the great video. Can you have a water chiller feed into the Big Mac instead of coming out of the Big Mac into a cold plate?

@francoisdore8673 2 жыл бұрын

Can you show how to replenish the sodastream bottle I have the 10lbs bottle but not able to replenish full the sodastream bottle and I don't know if I have to inverse the tank ?

@dorofino 3 ай бұрын

Great video! Thank you. One thing I'm not clear on is whether you are carbonating tap water at room temperature or using cold water from the cold plate. I understand that you need to carbonate cold water. What's your PSI setting for carbonating warm tap water.

@hasger1941 3 ай бұрын

hello thank you for sharing, wondering whether the gas inlet on these has a tube to bottom of the tank or feeds from above water level? we tried to build one though not getting much carbonation, we feed from top without a carb stone... TIA

@182nitesh 2 жыл бұрын

Hey Arnold I working on a small project and I have tried using plastic bottle for my carbonated drink but for some reason everytime drinks go flat after sometime - I would really appreciate if we can connect to discuss more in detail.

@MrMexc 3 жыл бұрын

i feel like getting a master's degree in physics is easier than doing everything in this video

@roycerepairs Жыл бұрын

Would this setup work?: city water-->mccann's pump-->[water pressure tank-->bigmac]-->flow control valve. [] means in fridge... purpose of the water pressure tank would be so I can have more cold seltzer available at all times and so it has time to sit and cool down in the fridge for optimal co2 infusion.

@miscaccount4760 3 жыл бұрын

Thank you for the video! Does the inside of the tank ever rust or go bad in any way? I have one that's been in storage for a couple years (not temp controlled at all so it got really hot at times) that I was going to start using but how do I kno that there's no rust, mold or anything inside the tank? Any enclosed container that once held water could get gross over time couldn't it?

@jeannihoul8914 3 жыл бұрын

Just spoke with Dave, and he says it should be fine, just run some cycles of water through it to kind of flush it out and you should be fine!

@paulbunyun4479 2 жыл бұрын

remove the float probe and look in the tank with a flashlight

@geeksnetmask Жыл бұрын

thanks legend Dave. how much fast is this setup for restaurant i mean how many liters can this machine produce in an hour for example?

@mway5050 2 жыл бұрын

Luis- I’m having a difficult time finding a seltzer tower with a compensator. Foxx is for the trade. Can you help? Also I was good to set my system up without the chiller, can’t I just add ice from my freezer directly into my cup? No room in the kitchen!

@ubershmekel 2 жыл бұрын

For anyone else having trouble finding the tap model. The search term I used was "flow control faucet" and it seems to find relevant results.

@Danfrd 3 жыл бұрын

Hey Dave! What is the best pump/carbonator setup for premixed root beer in a busy restaurant? 100 gallon setup using 2 to 3 beer taps

@paulbunyun4479 2 жыл бұрын

you don't need a carbonator for premix..just co2 to push the product out, thanks

@paulcataldo9895 Жыл бұрын

This video helped me a great deal getting a beverage trailer up and running for higher volume events. Ive been running since May with the McCann Set up and recently it appears that the carbonated water is freezing in the cold plate in one of my bins. I have a 2 tap system. Anyone have any ideas about this? Water runs with no ice but after the bin is filled with ice, water stops so my only conclusion is the cold plate is freezing up.. Crazy

@alex.velasco5338 2 ай бұрын

I took care of your help, how can I contact you.