How to Build 100W + 100W Stereo Amplifier Using TL084 IC With C5200 & A1943 Transistor

Рет қаралды 42,463

3 жыл бұрын

The video Build 100W + 100W stereo amplifier uses TL084 IC with C5200 & A1943 transistor powerful and low noise level.
➤ How to Build 100W + 100W Stereo Amplifier Using TL084 IC With C5200 & A1943 Transistor
➤ Copyright © by Share Tech Creative
➤ Follow me: / sharetechcreative…
➤ Follow Facebook: bit.ly/3eEHjNb
➤ 📺 Thanks for watching!
➤Schematic diagram:
photos.app.goo.gl/owNKrjTCipD...
➤ Parts Required:
Transistor:
- 2SC5200 x 2
- 2SA1943 x 2
- TIP 41 x 2
- TIP 42 x 2
- TL084 IC
Capacitor:
- 33p x 2
- 0.1uF x 2
- 0.22uF x 2
- 0.33uF/50v x 2
- 47uF/16v x 2
- 47uF/50v x 2
Resistors:
- 10R/5W x 2
- 220R/1W x 4
- 33R x 2
- 1K x 2
- 1K5 x 2
- 2K7 x 2
- 3K3 x 2
- 5K6 x 2
- 15K x 6
- 33K x 2
- 100K x 2
- 50k x 2 potentiometer
- Aluminum heatsink
- Mica pads x 4
- Diode 4007 x 4
- Diode Zener 15V x 2
- Audio jack connection
- Type Connector 2-Pole 5mm (connecting speakers)
- Power supply:
** +/- 40V DC 10A transformer**
See how to assemble power for the amplifier: • How to make Dual Power...
#diyamplifier #sharetechcreative

Пікірлер: 121

@ShareTechCreative 3 жыл бұрын

See how to assemble power for the amplifier here: kzfaq.info/get/bejne/Z5p7Y7Om1ZiaYIU.html👈

@bernardomalomay6288 3 жыл бұрын

Show diaram

@creative102st6 3 жыл бұрын

It's so powerful!

@pamornchuawong493 3 жыл бұрын

How many amps is the minimum power consumption? V and A

@Tariqlhr9 2 жыл бұрын

@@pamornchuawong493 Minimum on 24V this amp working nice and below 24v this amplifier working but sound quality not good. I test with minimum 20v and maximum 34v. I don't know what is the max voltage for this amp. Later I'll test with above 34v and if the circuit will not burnt I'll share my test with you. Over all this amplifier have very good sound quality.

@Tariqlhr9 2 жыл бұрын

By the way I used LM324 ic in place of TL084 and it's working nice.

@vincentrobinette1507 3 жыл бұрын

I like it: Since the big power transistors are current driven, there is no need for emitter follower resistors. This output stage is capable of full rail to rail output voltage. The only thing I might try different, is to replace the 1K resistor parallel to the series diodes, with two 500 Ohm resistors. then, I would connect the outputs of the quad OP amp to the junction of the two resistors. That would eliminate any zero crossing distortion, as one diode comes out of conduction, as the other conducts more. If that doesn't work, connecting to the junction of the two diodes, as shown in the video, is always an option. The diodes are necessary, create a current limit, by limiting the voltage that can appear across the 220 Ohm emitter followers on the TIP 41's and 42's. That limits base drive current, giving the amplifier some current protection, in case the output gets short circuited, or, the load impedance being too low. This would be a perfect output stage for a guitar amplifier, if no negative feedback was used.

@ShareTechCreative 3 жыл бұрын

Many thanks for the information

@jozsefbodor333 Жыл бұрын

Super!👍👋

@ShareTechCreative Жыл бұрын

Thank you

@jozsefbodor333 Жыл бұрын

Super!👍

@ShareTechCreative Жыл бұрын

Thank you very much

@joeyscott4299 3 жыл бұрын

Very nice !!! I love the design !!! I have some tl072 that I will use 2 of for your design . This will be a fun build ! Thank you brother !

@ShareTechCreative 3 жыл бұрын

Awesome, thank you!

@bastek. 3 жыл бұрын

Hello. Good idea👍👍👍Have a nice weekend 🙂🖐

@ShareTechCreative 3 жыл бұрын

Thank you! You too!

@irwandipulukadang3055 2 жыл бұрын

Thx for sharing ... 👍👍🙏

@ShareTechCreative 2 жыл бұрын

Welcome 👍

@manuelfonseca9937 3 жыл бұрын

Bueno ya lo hice y suena muy bien. . No distorsiona. Excelente. Es mi primer ampli sin PCB.

@ShareTechCreative 3 жыл бұрын

Yes, thank you very much

@RamirinRamiron-ow9vy 7 ай бұрын

Buenas noches desde Colombia para agradecer su video lo fabrique y muy bueno lo felicito sabe mucho yo estoy aprendiendo

@Creeptonic 3 жыл бұрын

Wow ! this is really awesome. This week has been especially rocking with 2 new designs from you. Thank you again for your hard work to share your gift. Much appreciated. Are you planning to share more Class A designs ? I have tried the 2SC5200 Class A Design and simply love it. Thanks again.

@ShareTechCreative 3 жыл бұрын

Glad you like them! Of course, please wait for my news. Thanks again!

@user-hr6xb7fz5h 6 ай бұрын

Desde cuba se ve muy bueno.

@singhelectronicsrajound2430 3 жыл бұрын

Very Nice

@ShareTechCreative 3 жыл бұрын

Thanks

@Tariqlhr9 2 жыл бұрын

Great Video 👍👍👍. Keep it up bro. This time I make no mistake and my amplifier working super good 💥💥⚡⚡👏👌👍😎⚡⚡💥💥.

@Tariqlhr9 2 жыл бұрын

Last time I was try one of the amplifier of yours. I don't know what mistake I was made , my amplifier was getting hot and I wasn't managed to get the fault but this time in first try ( with same parts which I used in faulty amplifier) my amplifier working 100% nice 💥💥. Thanks bro for such clear and easy instructions.🙏🙏🙏 You are the best 💓💓💓👌👌👌👍👍👍

@ShareTechCreative 2 жыл бұрын

Good 👍 Thanks

@kevinbeats1030 2 жыл бұрын

Dose it mean there is a mistake when it gets hot?

@kevinbeats1030 2 жыл бұрын

Or dose it just mean you need a bigger heat sink

@Tariqlhr9 10 ай бұрын

@@kevinbeats1030 Bro! Of course the amplifier gets hot but there is a limit to how hot it gets. If it is getting hotter than its limit then there is a short circuit somewhere in the circuit. Also sometimes, instead of the whole amplifier getting hot, only one component gets hot (except the main power transistors) and even after replacing that component the fault doesn't go away, it means that the circuit behind that component is faulty. There is no error. However, if only one component gets hot, then it is a fault and if the entire amplifier gets hot within a certain limit, then it is not a fault. In this case you can only reduce this heat away by using a large heatsink.

@lethimaile8355 3 жыл бұрын

Nice 👍👍😁😷

@ShareTechCreative 3 жыл бұрын

Thanks 😆

@loverforever4473 3 жыл бұрын

WOOOOOOW good job 👍👍👍👍👍

@ShareTechCreative 3 жыл бұрын

Thanks

@KOLEJ22DrogaPrzygody 3 жыл бұрын

Hello super video 🎶👌

@ShareTechCreative 3 жыл бұрын

Thanks for coming

@RJEDITALL 3 жыл бұрын

👍👍👍

@ShareTechCreative 3 жыл бұрын

Thank you so much 😀

@channelvemientay6555 3 жыл бұрын

Great👍👍

@ShareTechCreative 3 жыл бұрын

Thank you! Cheers!

@Ahmed_Show_Mit_Ghamr Жыл бұрын

Can you explain the AC 2030 with the same sound, this 100 watts

@manuelfonseca9937 3 жыл бұрын

Ouuuuu yeahhhhh!!😁

@ShareTechCreative 3 жыл бұрын

Thanks

@xorochi2183 Жыл бұрын

Ez jó!🙂👍👍👍

@ShareTechCreative Жыл бұрын

Thank you!

@loverforever4473 3 жыл бұрын

Big Liiiiii❤❤❤❤iiiike

@ShareTechCreative 3 жыл бұрын

Big thanks

@no-mo9gz Жыл бұрын

Please make care amplifier

@ShareTechCreative Жыл бұрын

We will try

@iulianvasile2870 5 ай бұрын

awesome job. can you provide please the schematic diagram for the full stereo version?

@ShareTechCreative 5 ай бұрын

Check description

@iulianvasile2870 5 ай бұрын

I've seen that, but is for one channel only. How do I connect 2 channel? @@ShareTechCreative

@ShareTechCreative 5 ай бұрын

@@iulianvasile2870 If you do two similar projects, it's stereo

@peteronel4051 2 жыл бұрын

Fantastic amp can you show circuit dia gram not easy to work of cell phone regards. Peter. South Africa

@abdalhamid5636 2 жыл бұрын

Can i use instead of tip bd139 and bd140 transistor my bro...

@JaviersDIY 3 жыл бұрын

This is very awesome sir. I will see you in my channel sir for support.

@ShareTechCreative 3 жыл бұрын

Ok thanks

@manuelfonseca9937 2 жыл бұрын

Lo hice tal cual pero recalienta demasiado el disipador de aluminio.Que debo hacer al respecto?

@teguhariffianto6724 3 жыл бұрын

👍👍

@ShareTechCreative 3 жыл бұрын

Thank you very much

@richie6920 3 жыл бұрын

Hello, where can I find the diagram of your amplifier, can you share it, please, thank you

@gamingcndorito 2 жыл бұрын

It's hard to find the tl084cn, do you think any other op-amp with same pin will work??

@ShareTechCreative 2 жыл бұрын

You can use the LM324 ic, the functions are equivalent! good luck.

@shadisy4145 6 ай бұрын

Hi can I use tip35 & 36 And What about THD% in this?

@ShareTechCreative 6 ай бұрын

Yes you can

@ourchannel8215 2 жыл бұрын

any ic can be used sir?? TL072 or LM358

@kevinbeats1030 2 жыл бұрын

whats the maximum voltage for this amplifer

@ShareTechCreative 2 жыл бұрын

DC voltage max: +/- 45v

@victorsantanpagay5811 Жыл бұрын

Is pcb is really hard to made for your?

@Tariqlhr9 2 жыл бұрын

Bro TL084 not easily available in the market and also more expensive ( Approximately RS.100 to RS.150) therefore I used LM324 ( quality and pinouts are same like TL084) but It's much cheaper (approximately RS.30 to RS.45)and easily available in the market or from Scrap ( I get this ic from an old and scrap 18v charger). I don't know what quality is TL084 have but LM324 have very good sound quality. My amplifier is complete now give me the link of your video which have tone and bass control circuit for this amplifier. I mean to say how to connect tone control to this amplifier.

@ShareTechCreative 2 жыл бұрын

Hello, LM324 quality is excellent! but you use TL084 even better. Thank you for supporting the channel and leaving a comment.

@kevinbeats1030 2 жыл бұрын

did you use 40V 0 40V 80V as power supply or lower

@MAK786GO 11 ай бұрын

Can i use 3.3omh 5w resistor? On speaker output

@ShareTechCreative 11 ай бұрын

No, you can use a resistor of less than 1 Ohm

@MAK786GO 11 ай бұрын

So I can use 0.33 ohm?

@ShareTechCreative 11 ай бұрын

@@MAK786GO Yes

@ranodyanethmi7541 2 жыл бұрын

LM 324 ai used

@ShareTechCreative 2 жыл бұрын

Yes, you can use LM324

@rk5672 Жыл бұрын

Schematic diagram link is invalid. Pls. Refresh the link ir upload again.

@rici_21 2 жыл бұрын

If i want to connect equaliser to it, i am connecting it to speakers output ?

@ranodyanethmi7541 2 жыл бұрын

+/_32VDC can be used

@x2gogo 2 жыл бұрын

Excuse me, can I use the lower noise TL074 ?thank you!

@ShareTechCreative 2 жыл бұрын

Yes you can

@alandamianllanes2425 2 жыл бұрын

Cuanta pulgada son eso parlante

@ShareTechCreative 2 жыл бұрын

12-inch speaker

@vishanth18 Жыл бұрын

streo to momo canistion sir

@marlonarias1512 2 жыл бұрын

Me gustaría saber cómo acer una voz ter ampliable para 4 canales

@ShareTechCreative 2 жыл бұрын

Puede agregar un circuito amplificador 4558 ic para expandir

@roldaoviana653 3 жыл бұрын

has it mono?

@cesarvasconez9481 9 ай бұрын

Las cuatro resistencia qué dices de 220 ohms son de 22 ohms.

@SS-mj2mq 3 жыл бұрын

Yes I would like to know what is the wattage of that zener diode do you know or could you possibly give me the model number thank you 🤗

@ShareTechCreative 3 жыл бұрын

Diode Zener (0.5W) 15V

@specialistka1 3 жыл бұрын

schemadig diagram please!

@user-hr6xb7fz5h 6 ай бұрын

Porfabor me pasas el diagrama.

@kevinbeats1030 2 жыл бұрын

On the 224 0.22uf capacitor what can i use instead cant find that value locally and am almost done with the amp. Please help

@ShareTechCreative 2 жыл бұрын

You can replace them with the value 0.22uf = 1uf

@kevinbeats1030 2 жыл бұрын

Thank you will do that

@everythingsoftware681 2 жыл бұрын

what can you do to increase the output to 130W

@ShareTechCreative 2 жыл бұрын

You can upgrade to 8 transistor C5200 and A1943

@kevinbeats1030 2 жыл бұрын

@@ShareTechCreative okay will try that but don't know how to connect them though

@vineetsharma3735 2 жыл бұрын

make a class a discrete board and vacume tube amp class 50 +50 watt

@chaudharyonlineprintingpre4455 3 жыл бұрын

Complete price kitna hai

@ShareTechCreative 3 жыл бұрын

main is empaleephaayar ke lie puraane ghatakon ka upayog kar raha hoon

@zayanshaikh8454 3 жыл бұрын

bro music name

@tayfun.b.. 3 жыл бұрын

Does it run 12v

@ShareTechCreative 3 жыл бұрын

Can not

@lalalazar4639 3 жыл бұрын

You are just making, please tell us the thurie

@gerocire 3 жыл бұрын

el link no funciona Dynamic Link Not Found Short URL (photos.app.goo.gl/owNKrjTCipDx5vEj90) not found If you are the developer of this app, ensure that your Dynamic Links domain is correctly configured and that the path component of this URL is valid.