Playboi Illinoisey Hello. Thank you for the happy message ! Also make a good movie now . Thanks for watching!

Thank you very much. I will do my best in the future.

+Marcell Mrsan Thank you!

Thank you so much for watching my vedio. making time 4hour for last one foot. 見てくれてありがとうございます。片足の木型を作る時間は４時間です。

I don't know what a finished last is supposed to look like. I just ordered a pair of plastic lasts and will now begin to understand. 4 hours! WOW.

Thank you very much!😸

Gracias por el mensaje usted. Me sentí alentado por sus palabras. También Ganbarimashō el uno al otro ahora. Japón es la temporada de frío. También tenga cuidado de su cuerpo. Gracias.

Hi Zorro,thank you very much message to me. I make video for want to make last people in the future. Try it(^^)

Thank you very much!

Thank you !

+Betosneakers Thank you !

Thank you so much.

Thank you!

You can make a last yourseif. Try it ^^!

Thank you very much!

Hola Gracias por el mensaje. Usted estoy feliz si me hace feliz . También por favor los zapatos de la suerte de hacer .

It's measure twice, cut once. All feet are different sizes, for starters, mine were in the military so more heavily muscled, wider and higher than most, because they lived in boots for so long. Women follow the Ladies of the Twilight World, forcing their feet into shoes which do the opposite at an ealry age, and so tend to have narrow feet with little arch to them.

Hi turesuregusa, Thank you very much. Your video is also great. Saw the sharpening of Japan. Very difficult. Wood I use is tuga. I can use a variety of trees other than tuga.

Thank you so much! I don't know how to make boots for decor on a wooden Texas coffee table.

Nishimura-San Because they're for decor, they don't need to be sized to an individual's foot, so a commercial last should save time. Otherwise, they are made like any other, with more attention to the leatherwork, so use vegetable tanned leather, to allow tooling. That again is another subject, as is the shade-dying and sealing.

Cast your foot in two sessions, firstly the sole (use silicone grounting stiffened with maize flour, wear plastic gloves and cover your feet with cling film over pop-socks) and embed dowels in it, vertically around the edge, so the cast for the upper always lines up with the sole. Then, after coating the upper surface of the sole with food oil to stop the top adhering to it, repeat doing the top. That then creates a female cast, finally once it's dried (48 hours) fill it with a plastic skin (just swill your resin in fairly dilute form around inside until it sets) and finally fill the core with epoxt foam, if you can find it, for lightness.

Thank you too!

The late reply sorry. 返信が遅くなってすみません。

Thank you!

You can buy it in Japan. Now you can only buy it in Japan.

Thank you so much.I use japanese general tools. ありがとうございます。私が使っている道具は日本の一般的な道具です。Amazonで買えます。

The Western equivalent of the curved planes are spokeshaves, which are in the draw-knife family - look for curved ones. The saws, you must use Japanese, they are far better than the European sawdust-makers. What Nushimura-san does not show are his sharpening tools, which are almost certainly Japanese water stones. I use three grades, 800 for rounging the edge out (which already takes it to better than a grindstone), 2000, and an 8000 slipstone to finish the edge. You can go to far finer grain than that, which is useful if you intend working in the harder exotic timbers, but less so for general softwood carpentry. They are used with water instead of oil, and create a cutting slurry, raising the normal thread on the tip, which you use the slistone to remove. Always be aware of the shape of the tool you want to end up with, being careful to remove just a little more at the edge than in the middle, you don't want to hollow-grind a flat chisel - except when you do actually want to! Mostly you'll sharpen on the slope of the chisel rather than it's belly, as a result. The Japanese chisels are just shortened versions of Western ones, because quality metals were very scarce until the West started selling them steel in volume, and so lesser quality was used as far as possible, producing more resilient tools.