Shop Work: Grizzly T33902 Drill Press Review

Рет қаралды 31,884

Күн бұрын

Check out the amazing machines over at Grizzly!
SPONSOR: www.Grizzly.com
Website: www.FishersShopOnline.com
Plans: www.FishersShopOnline.com/plans
Instagram: / fishersshop
Store: www.Amazon.com/shop/fishersshop
T-Shirts: www.FishersShopOnline.com/store
Podcast: webuiltathing.libsyn.com/
I finally got a new drill press for my shop! The newest Fisher's Shop family member is the Grizzly T33902 14" Drill Press. In this video, I unbox and setup the new machine and give a run-down of all its features. I discuss my likes and dislikes and show you how well it performs.
00:00 - Introduction
00:23 - Unboxing
01:23 - Setup
04:05 - Price
04:18 - Motor
04:34 - Swing
05:18 - Travel
05:37 - Workspace
06:05 - Speeds
06:40 - Depth Stop
06:57 - Light & Laser
07:17 - Work Table
07:35 - Chuck Guard
08:09 - Chuck Key
08:40 - Power Switch
08:55 - Table Adjustments
09:37 - Zeroing Table
10:52 - Changing Belts
12:34 - Height
12:54 - Noise
13:32 - Run-Out
14:45 - Testing
15:44 - Outro
16:32 - Outtakes
Join Fisher's Shop!
/ @fishersshop
Affiliates:
WilliesWoodFinishes.com - "FISHER10" to save 10%
CadenceMfgDesign.com - "FISHER10" to save 10%
SurfPrepSanding.com - "FISHER10" to save 10%
Starbond.com - "FISHER10" to save 10%
Mag-Tools.com - "FISHER10" to save 10%
Merlin-Technology.com - "FISHER10" to save 10%
TersaKnives.com - "FISHER10" to save on RALI products
Bumblechutes.com - "FISHER10" to save 10%
RZmask.com - "FISHER10" to save 10%
This video was sponsored by Grizzly Industrial

Пікірлер: 174

@Sebastopolmark 2 ай бұрын

OK class, what have we learned; 1. Toss the red "safety" thing 2. Use your old chuck key 3. Yell at Grizzley and have them put a detent to keep the table level 4. Wait for Drew to make the mobile base for the new machine. Until the next video! !! !!!

@FishersShop 2 ай бұрын

Haha, perfect!

@MikefromMOMichaelTurner227 Ай бұрын

Old retired machinist guy here.I agree 😊 spindle guard can catch chips and friek you out 😊

@Jacob-5949 Ай бұрын

You can typically take the safety pin and spring out of the chuck key by removing the cross bar.

@cashkruz319 Ай бұрын

LOL...dumping the whole socket set on the floor is soooo relatable. That's why I keep coming back to this channel...and the great project videos. Thank you!

@FishersShop Ай бұрын

Glad you enjoy it!

@rjtumble 2 ай бұрын

Your neighbor sure did have a nice drill press.

@pjhalchemy 2 ай бұрын

Congrats Drew! Couple of things: When measuring runout get a 6"-8" piece of 1/4 or 3/8 "Precision Ground rod", seat it into the chuck and tighten, then use your Dial indicator or better a .005 DTI and take measurements at the far end and at the 1-3.5" (Typical drill lengths). Keep in mind that typical drill tolerance is about .005ish. Resetting the Morse taper in various radial positions will allow you to dial it in for whatever your needs are. I also use the a shorter 1/2" ground rod (also use on router table) to do the initial Morse insert floating it up into the receiver and apply slight pressure with the handles then Love Tap it home. I got my 1950 Craftsman/KingSeely down to .015@3" after some fiddling and restoring it. Second is: after these belts wear out or Not, get some link belts (Spendy) but worth to reduce the noise level about 10db. Nice work with the magnets for all the other rattlers. I Know, Nerdy right?...its just me. ;-P Thanks Much, I always appreciate what you bring to the community!

@woodrowsmith3400 2 ай бұрын

Link belts are the bomb. Have them on all my belt driven stuff. For about the last ten years or so I've been getting them at Harbor Freight for $35 or so a pack...4' if I remember correctly. Seem to run as well as the red ones for much less dineros. Coolest part is the ability to weave a belt of any length. I try to keep 3' or so on hand at all times cuz you just never know...

@frogmann49 Ай бұрын

Nice one. I had 3 drill presses over time that I didn’t like, they all had a bad wobble but I just put up with it. Awhile back I ran across a Grizz band saw that I got and liked it. So last year I bought the drill press similar to yours. It has variable speed adjustment which I really like. It came with a keyless chuck which I didn’t notice and thought “uh-oh”. So I set it up and had to immediately run over to my neighbor’s house and get a high five. As with yours there was virtually no run out. For the cost and quality, Grizz is the GOAT. Thnx for the vid as always. P.S. I also think YT is ghosting you. Had to find this in my subscriptions.

@FishersShop Ай бұрын

Thanks, glad you liked the vid. Yeah, YT has gotten weird about how it shows/recommends videos.

@CarlManson1983 Ай бұрын

Heard you on the podcast saying that this video isn't getting the results you were hoping for. Well, I just thought I'd let you know that, for me, it didn't even appear in my feed. I had to hunt through my subscriptions. Keep up the good work Drew.

@FishersShop Ай бұрын

Yeah, I'm not sure why YT functions the way it does now. So annoying

@--KT-- Ай бұрын

Congrats on the upgrade, enjoy your new toy! 😎 Not being an expert by any means, just from a personal experience - a keyless chuck makes things much more convenient. And they are not that expensive.

@FishersShop Ай бұрын

Yup, that's on the list to get shortly

@devinreynolds-FDW 2 ай бұрын

Thank you for this video fisher and it was a great video again like everything else u do!!

@FishersShop 2 ай бұрын

Thanks!

@daniell.5654 Ай бұрын

I watched the video and I thought "that wasn't really boring". Went to bed and woke up and thought "wait, doesn't the word boring also mean to make a hole??". I might sound dumb but that was very clever. So yes, it is definitely a boring machine!! Thanks for the content.

@FishersShop Ай бұрын

Haha, took you a minute. 😉

@glencrandall7051 2 ай бұрын

It seems like a decent machine. Thank you for sharing. Have a great day and stay safe.🙂🙂

@FishersShop 2 ай бұрын

Thanks, you too!

@curtesamoangelos5995 2 ай бұрын

Watching from Yosemite Kentucky. Great video. Thanks for sharing.

@FishersShop 2 ай бұрын

Thanks for watching!

@SawdustmakerLori 2 ай бұрын

How exciting that you got a new "toy" and a nice one at that. It will be a great addition to your shop!!! Enjoyed the honest and thorough review. Maybe your tips will help Grizzly with a few things that could make this drill press even better in the future.

@FishersShop 2 ай бұрын

Thanks 👍

@paulellis84 2 ай бұрын

Over the 400 views in 20min. Pretty good. Great video again, sir. Thanks for posting!

@FishersShop 2 ай бұрын

Thanks for watching!

@rpaasse6453 2 ай бұрын

Nice drill, congratulations and many happy holes!

@FishersShop 2 ай бұрын

Thank you very much!

@MCsCreations 2 ай бұрын

Pretty impressive tool, Drew! Congrats! 😃 Stay safe there with your family! 🖖😊

@FishersShop 2 ай бұрын

Thanks

@skene59design 2 ай бұрын

Can’t wait for your version of an adjustable drill press table (for drilling angles holes)

@nickmatney6605 2 ай бұрын

Good looking drill press! The best drill press upgrade I ever made was wiring in a foot pedal. This allows you to use always have both hands available for quill and workpiece.

@FishersShop 2 ай бұрын

I guess I don't understand how that makes it any different then how I operate it now. What am I not getting?

@philshock3805 2 ай бұрын

@@FishersShop Many times, I'm trying to hold the workpiece with one hand, the handle (quill?) into position with the other hand, while simultaneously trying to hit the run switch. Usually I can stretch a thumb to hit the switch but not always. Not sure a foot switch is worth the effort/cost, but I can see how it'd be beneficial.

@dougprentice1363 Ай бұрын

Why would you need a foot switch? Turn the motor on, then drill.

@robt2151 Ай бұрын

@@FishersShop A sewing-machine type 'accelerator' allows you to start cuts slowly before increasing to the set speed. Useful, for example, when drilling into tubes.

@--KT-- Ай бұрын

@@robt2151 But not with the induction motor like this - you would need a VFD (variable freq drive) to control its speed.

@halsonger1317 2 ай бұрын

My older Delta floor drill press has the same depth setting type. It is truly wonderful compared to the knurled nut aggravation that was on my old benchtop drill press. One neat feature is that you can set it to drill to an exact distance by putting a setup block at the bottom of the depth stop, then slide the cylinder stop down to set a precise depth. You can also stick your workpiece in there and set it to drill precisely to whatever thickness it happens to be.

@FishersShop 2 ай бұрын

Right on! Great tips

@greggrote Ай бұрын

Nice. Love that depth control ... much better than the "set screw" type stop on my Grizzly benchtop radial drill press. And mine doesn't have a laser either, but the motor noise is similar to yours.

@FishersShop Ай бұрын

Yeah, that's definitely much better than the one I had before.

@Counterpoint69 12 күн бұрын

Hay Drew, my car antenna is missing. Do you know what could have happened to it?🤪 Great video. Many thanks.🙏🏻

@keithgoldston2859 2 ай бұрын

I have the modle from about 10 years ago the first thing to go is that Chuck garde its a great machine you will love it

@FishersShop 2 ай бұрын

Yup, that thing went bye bye almost instantly

@mwoody4560 Ай бұрын

I wish more drill presses would come with a woodworker vs metalworking table. I’d like to have both and change them out as needed. Nice review. It’s a good drill press at a very good price.

@FishersShop Ай бұрын

Good point, that would be nice. Thanks for watching

@jimrosson6702 Ай бұрын

Great video Drew

@FishersShop Ай бұрын

Thanks 👍

@Dan-il9rz 2 ай бұрын

I have the exact drill press... right down to the handles on the spindle. The laser and light are different, my light is on a gooseneck. I think I like that better. The only difference is it is branded as a Craftsman. As far as height I have a dedicated stool I keep at the press because I am 5'11" and can't really see what I am doing standing up straight.

@toolchuck 2 ай бұрын

Drew, I enjoy your channel and I have built a couple of your projects, which were great designs. But I must comment on your table tramming or leveling and your chuck calibrating. Firstly, the table tramming should be done after the chuck is calibrated. If it is off and adjustments are made, the table will need to be trammed again to the newly adjusted chuck. Secondly, the chuck runout should never be taken from the chuck body as it has nothing to do with how the bits are being held by the jaws. it should be done with a 1/4" or 1/2" etc.(depending on the chuck size) calibration rod or dowel. It should be inserted deep enough so that the feet of the jaws are fully engaged, as should be best practice for all bits when using a Jacobs style chuck. Then measure the runout against the rod for an accurate indication of what the chuck is doing. A calibration rod or dowel is only $20 or so, and well worth the price. Thirdly, NEVER set the chuck into the spindle taper by hitting against the jaws!!! The jaws MUST be fully retracted so only the chuck body is struck. It is better to place a block of wood against the chuck and then Strick the block of wood to seat the chuck. Striking the jaws is very detrimental chuck. We are so used to seeing Jacobs style chuck on everything that most people don't realize just how complicated a piece of precisión tooling they really are. All the Best, Chuck. (No relation to Jacobs) 🤣

@tommysts1920 2 ай бұрын

Looks like my Delta except it is older and doesn't have the laser and light I installed a magnetic light and also made my own electric lift using an old electric trailer tongue jack motor. I love this drill press now. I noticed the big drill press at Harbor Freight is also like this model, so some manufacturing company over in China must be making them all. Love the bloopers at the end of your videos. Reminds me of myself.

@FishersShop 2 ай бұрын

Electric lift? fancy!

@madsk2595 2 ай бұрын

Great video! Will definatly consider buying this drill-press/dental-work/lobotomy-machine! :)

@FishersShop 2 ай бұрын

Great for all occasions!

@Kami8705 Ай бұрын

Locktite on those quill handles is a good idea. I'd also grease the table raise and lower, but thats just me maybe

@gerardcarr9140 Ай бұрын

I think that little plastic thingie around the chuck ,is so it can comply with euro rules

@RidgidRon 2 ай бұрын

The drill press defiantly has some similarities to my Porter cable drill press!!

@williamellis8993 2 ай бұрын

Looks like this is a nice addition to your shop. I figured you used walnut because that's what your neighbor had available. Bill

@FishersShop 2 ай бұрын

Thanks 👍

@Zoso14892 Ай бұрын

I can't believe they didn't give you a custom job. I'd have swapped one of the adjustment screws from a hex key to a flathead just to mess with you!

@FishersShop Ай бұрын

Hah, I would have appreciated that

@johnshumake3696 2 ай бұрын

I just got the Grizzly sawmill. It will handle a log 48 inches by 13 inches. Came in a wood box with a shipping weight over 500 pounds. Lots of nice heat treated pine for pallet wood projects. It was easy to put together in my garage. Iy also runs on 115 volts. I milled some black walnut and the results are very good. You can't blast thru like the big gas machines, but that is not what it is designed for. Another win for Grizzly. 😊

@FishersShop 2 ай бұрын

Sounds fun

@crossgrainwoodproductsltd9230 2 ай бұрын

Great review. It's always fun to get a new toy! You will need a platform of some kind for it to sit on or you will end up looking like Quasimodo.

@FishersShop 2 ай бұрын

Yeah. I'm think a mobile base that will lift it up higher

@justa_grandpa 2 ай бұрын

You can also use a Wixey on the column, set to 0, then place on the table to adjust the table to perpendicular

@williamellis8993 2 ай бұрын

This is the easiest way.

@FishersShop 2 ай бұрын

But then your neighbor is out there flaunting his car antenna to everyone!!

@williamellis8993 2 ай бұрын

@@FishersShop Good point.

@renaissancewoodworking Ай бұрын

Very nice! I have an old Craftsman floor model. It’s not perfect and I have to body wrestle it anytime I need to change the height of the bed. But, it works. 😂😊

@FishersShop Ай бұрын

Sounds like my previous press

@mburke1211 Ай бұрын

If only you could be there next time your neighbor tries to tune to his favorite AM station!

@chrisp7957 Ай бұрын

Free tools are always exciting

@rudyschwab7709 Ай бұрын

Yes, but then they end up in the free tool drawer (a.k.a. Drawer of Misfit Tools) to never be used again. There's the 5.6mm open end wrench, the 3/10" hex wrench, and a metric screwdriver. I don't mind though. It's almost like a collection of trophies.

@philshock3805 2 ай бұрын

My old Delta I bought from Lowe's about 8 years ago ($350 ish I think), is the same style with the same type of depth stop. It's not the smoothest running machine but gets the job done. I think if I invested in a better chuck, it'd be a huge improvement in the runout dept. One thing I really like about though it is that it has around a 4.25 in quill travel.

@FishersShop 2 ай бұрын

Nice!

@jonwooddell3966 Ай бұрын

Drew, congrats on the new shop upgrade. How soon until we can expect the video on your drill press table? Not because I bought the bench top Grizz press or anything...

@FishersShop Ай бұрын

Hah... it'll be something for the future, but I'm not sure when. The docket is filling up with projects already

@gnic76 2 ай бұрын

My drill press came with a similar guard, it got tossed in a drawer and I put a wider, mobile base under it.

@FishersShop 2 ай бұрын

Yup, I'm thinking I'll do the same

@WreckDiver99 2 ай бұрын

Hmmm....so, at least I know where that Grizzly Drill press I ordered went. Drew at it again! Yea, I bet that thing just 'showed up'. uh-huh...right off my front porch! Actually I inherited my dad's Delta Drill Press. Looks as if that design was so good that Grizzly used the same one. LOL. My Delta is 40 or so years old, and doesn't have integrated lights and lasers. :( It also doesn't have the requisite lawsuit protection "Chuck Key Guard". As for changing speeds? I change mine fairly regularly, but I drill plastic, steel, wood, aluminum, etc. Nice new toy!

@FishersShop 2 ай бұрын

Thanks!

@feedthechunk9836 2 ай бұрын

Make a base. For mine I used 2 2x4's on edge and 3/4" plywood. It makes it a lot more stable and it's at a perfect height fore me, 5'10".

@FishersShop 2 ай бұрын

Yes, I will be making one eventually

@thebobloblawshow8832 Ай бұрын

👍👍

@AndreaArzensek 2 ай бұрын

This is an okay-ish drill press, but far superior to the last one you've had. Many of the features are really for metal workers and not intended for woodworkers. But that's the case with almost all the drill presses on the market. After many of them I owned and used at my job I found about Nova Viking and it is a complete game changer. It is made for woodworkers in mund and all electronic with direct drive (no belts), has digital depth stop and many incredible features. The only "negative" is the cost I paid €1000 for it (in 2021) so it is double than todays cost of Grizzly. There is also another model (Voyager, I guess) that's even more packed and capable, but for me Viking is more than I ever wanted. If you're not tied in with Grizzly, try one of the Nova models. PS there is Viking review of David Picciuto on YT.

@FishersShop 2 ай бұрын

Yeah, I'm familiar with that press. It's just overkill for anything I do.

@gcarson19 Ай бұрын

I'm a woodworker, but not in mund. Can I still use it?

@KTX666 Ай бұрын

I was surprised to see that there wasn't a safety switch on the belt cover. I think that would have been the safer safety option than a guard that doesn't do anything other than get in the way, and a chuck key that are specifically designed to not do what a chuck key should do...

@FishersShop Ай бұрын

I agree. I think the higher-up models have a micro-switch on the top cover

@stephenmcdowell4190 Ай бұрын

UGH... *Grabs my scientific specimen collection card, a zip tie and a 2x4, and jumps in my State Biologist work truck* "Well, now I HAVE to go catch a woodpecker for Science..."

@FishersShop Ай бұрын

Make sure it's a walnut 2x4 and a Pileated woodpecker. Those seem to work the best together.

@clydedecker765 Ай бұрын

FIRST thing I did for and with my floor drill - make a higher base plate with leveling feet and a wider stance. Once it got to a height I could actually use. Then I built a good sized table with inserts and a fence etc to bolt on that dinky table they have.

@FishersShop Ай бұрын

Yeah, I'll be doing something similar eventually

@clydedecker765 Ай бұрын

@@FishersShop I had to - The base was so small and narrow it was unstable and rocked really bad because the floor was not level. And the things I wanted to drill were too big for that dinky table.

@WalterRiggs 2 ай бұрын

I wonder if the safety thing would help direct shavings toward a dust collection area. If not: toss it

@FishersShop 2 ай бұрын

I thought about that too. I think that's the only reason I'll be keeping it

@chrisfisher1663 Ай бұрын

I was wondering the same thing, but also thought it was more to protect against flying/twisted shavings when drilling through metal.

@DanielTaylor-hn4ut 2 ай бұрын

Love it. Not a bad price, either... I need to move now to a house with a generous supply of neighbors with wood I can rob. The cop on one side of me gets irritated when I steel his, and the fireman on the other side has no sense of humor about my scrap wood bonfires.

@velcroman11 2 ай бұрын

My drill press is 98 years old. It is a Richardson drill press with a Noyes 1/2 hp. single phase 240v motor. BTW, even if you have the best drill press in the world, one will never drill a decent hole if the drill bit is blunt, poorly sharpened. The most likely a bad drill is produced occurs by not drilling pilot holes.

@G.I.JeffsWorkbench Ай бұрын

Great overview. Glad I’m not your neighbor. Seriously, I’m very particular about presentation style & based on yours I figured I’d subscribe. I’m about your height. I’ll be interested to see how you raised the press to a more comfortable working height.

@FishersShop Ай бұрын

Thanks and welcome. Yes, that'll be coming in the future sometime

@mcmathwoodworks 2 ай бұрын

Well Drew it’s good to know if you ever get tired of woodworking you can become a Dental Hygienist. Lol I’m glad they let you keep that dental joke in there! Have fun with your boring new machine.

@FishersShop 2 ай бұрын

Haha, thanks!

@EthanCarterDesigns 2 ай бұрын

What an upgrade! This video most certainly would have been "boring" without the dad jokes!

@FishersShop 2 ай бұрын

Haha, it would have been. I tried to make it bearable

@PJRayment Ай бұрын

@@FishersShop "I tried to make it bearable" As in grizzly bear-able?

@gcarson19 Ай бұрын

Are there a lot of people leaving the chuck key in while turning on the machine? Been using one for 50 years, and not once have I done this...

@FishersShop Ай бұрын

I did once as a child on my father's drill press when I was learning but never again.

@mrow7598 2 ай бұрын

For the price that's not bad.

@woodrowsmith3400 2 ай бұрын

I have been an infrequent but loyal customer of Grizzly since the late '80's. I'm not sure why Griz isn't in more shops. Their machines have always been decent, and always as advertised. Maybe it's lack of brick n mortar stores, or lack of everyday, in-your-face advertising...I dunno. One secret is their purple line of router bits. Every bit (pun intended) as good as the red ones. Price is attractive as well...enough so that a couple of bits offsets the shipping. It's prob'ly time for me to go thru my collection and see what needs replaced, as a few of my straights and template trimmers are getting pretty tired. Hmmm....

@FishersShop 2 ай бұрын

Hey thanks for watching! Nice tip on the router bits too

@aaronblackford981 Ай бұрын

I have always wondered how much you understand watchers humor in comments. My humor is pretty dry which seems to fit your video humor but is that your real humor norm? And can you appreciate viewers dry humor for what it is. Thanks for the video.

@FishersShop Ай бұрын

I don't have the patience nor the skill to "fake it". What you see is what you get with me.

@Lorddanielrushton371 2 ай бұрын

Drew, can you do a video in a year? See how well the drill press is working.

@FishersShop 2 ай бұрын

Ummmm, probably not.

@vmoutsop 2 ай бұрын

Keyless chuck - Upgrade

@stevesiefken6432 2 ай бұрын

Please tell Grizzly I have an old terrible drill press that needs an upgrade 😂 Great video learned a lot!👍🏻😊

@FishersShop 2 ай бұрын

Glad it was helpful!

@FearsomeWarrior Ай бұрын

At 6 feet 7 tall do I just put this on the bench top?

@FishersShop Ай бұрын

Haha, yes.

@dougprentice1363 2 ай бұрын

I think it's many, not just me, that never bother to change the speeds. It really doesnt take long. Im lazy.

@gedreillyhomestead6926 2 ай бұрын

First jobs - 1. Mobile base 2. A proper table. 🏴󠁧󠁢󠁳󠁣󠁴󠁿 👍

@guillermocarrillo3959 2 ай бұрын

Hate to say this but it looks exactly like the Harbor Freight drill press. Where is it made?

@FishersShop 2 ай бұрын

I think most of their stuff is made in Taiwan

@dusbus2384 2 ай бұрын

The spec sheet online says it's made in china

@greghomestead8366 2 ай бұрын

@@dusbus2384 I think 99% of stuff is. Sad but true

@johngregg5735 Ай бұрын

Good, helpful video I don't mean to tell you your business but you could turn this into three separate video's. You could call it a Drillogy... lol

@FishersShop Ай бұрын

I like it

@Danman1972 2 ай бұрын

Did you steal this package off your neighbors porch? ;-)

@cabman86 Ай бұрын

I looked up the model number on Home Depot and they sell it for $774.

@FishersShop Ай бұрын

$654 in my area. But delivery is free so it's actually a good deal

@superwesman 2 ай бұрын

Homie....why don't you just stick a long bit or other straight piece of metal in the chuck and then use a square to square it to the table? Probably easier and more accurate than your floppy wire...

@FishersShop 2 ай бұрын

How DARE you call my wire floppy!?

@superwesman 2 ай бұрын

@@FishersShop hey-o! 😂😂✌🏽

@tomcatfoolery Ай бұрын

Did your new drill press go to plaid at ludicrous speed?

@FishersShop Ай бұрын

Yup. 😉

@greenmtguy4593 6 күн бұрын

They already jacked the price another $40

@FishersShop 6 күн бұрын

That's unfortunate. It definitely wasn't because of this video though. This video didn't do that well.

@henrysara7716 Ай бұрын

Thy, Wood and steel shavings love to go visit your eyes.

@CyranoHadden 2 ай бұрын

There had better be an unnecessary walnut stand in the future

@FishersShop 2 ай бұрын

I like the way you think

@thelegendricky 2 ай бұрын

Im about 5'6 and I have a bad back. Im by no means classified as being "tall" but it seems though ALL shop tool manufactures build their tools for midgets! I have had to build a wooden box "platform" for nearly all my tools to raise them up tall just tall enough so I dont have to bend over while using them. Constant bending and stooping kills my back! I have mobile bases under all the tool platforms also. Come on guys! Make shop tools more back friendly!!

@FishersShop 2 ай бұрын

Couldn't agree more!

@James-lo5ne 2 ай бұрын

you made it look easy, I bet you work out and drink whole milk and not that 2% crap.

@jimharrison8176 Ай бұрын

Where I worked they had 3 grizzley drill presses. They kept the tool repairman busy. He could never het them to work right, worst drill presses I ever used.

@alberttreado3713 2 ай бұрын

Excellent use of unnecessary walnut. You may need to replace a screw with one of grandpa’s slotted ones!

@FishersShop 2 ай бұрын

I think you're right

@dusbus2384 2 ай бұрын

Man what I love about your channel vs other woodworking channels is its focused on projects and actual woodworking rather than being tool infomercials. I get it you make a video and get a free drill press but I hope it's not the beginning of a trend...

@nkgoodal 2 ай бұрын

I think he did a good job of reviewing with integrity, but I like your point: there are way too many tool buyers/collectors/reviewers pretending to be woodworkers on youtube.

@AndrewMcQuillen Ай бұрын

That was a boring one Drew😂, those plum eating Roberts get all the breaks.

@FishersShop Ай бұрын

Exactly!

@gerrysherman2007 2 ай бұрын

Do yourself huge favor and get a keyless chuck. You'll thank me forever.

@louiswhitney1761 Ай бұрын

I know I bought a table saw from grizzly and found it so complicated to build I sold it for half price so I didn’t have to finish it… I will never do business with them again… 😢😢

@bw162 2 ай бұрын

Unless your neighbor is 3’ tall, need a reclining dental chair

@cliff5240 Ай бұрын

Now it is time for you to make a drill press table with unnecessary Walnut -- not real woodworking until you make the table :)

@FishersShop Ай бұрын

Something for the future! :)

@alexanderwood6739 2 ай бұрын

Woodpecker tied to a stick..... $15,000 from woodpeckers lol

@FishersShop 2 ай бұрын

Hmmm.... might be more expensive actually.

@NedbLegocity Ай бұрын

And… off goes the red doodad… right after he wrapped…

@FishersShop Ай бұрын

Yup!

@NedbLegocity Ай бұрын

@@FishersShop looking forward to the lift kit install. I’m 6’3 and have a shopsmith. Apples to oranges a, but I’m curious what you are going to do to raise the whole machine safely