Is the shift knob shaft M10x1.5 or M10x1.25?

I'm glad someone watches my videos, besides SimCat. 😺👍

But in my case, I had to move the Hall Sensor PCB a bit to the front (slanted side), as the magnet "overshot" its target by a millimeter or so, causing a second triggered event on its way back. But that was an easy fix, and the shifts feel sooo satisfying. (I upgraded from the magnetic AliExpress shifter.)

After a few hours of serious banging, I noticed my shaft also getting lose. (Puns intended, of course.) So I opened up the shifter to see what I can do. Turns out Sim Jack put an additional bolt between the interlocking plates which, after adding some thread locker and re-tightening the nut, successfully eliminates the play. As I can neither add photos nor links here, I'll send you an email showing the new internals.

Great, that's good to know.

Thanks!

Is it up there with the aiologs 180$ shifter. Design and all make them direct competitors I feel. There is no clamp for this one?

Thanks very much! I should have their h shifter arriving in the week, so I'll run out an unboxing when it arrives.

I'm curious what the difference is in comparison. I just ordered the cheaper h-pattern one. Hope it will be fine for my needs :-)

That's something I'll look at as well.

I'm interested to know if the h pattern is hall effect as well.

@@7MBoosted I will check that when it arrives, and mention it in the unboxing this week.

I do know Moza are close to releasing a shifter, I don't know if it's Seq, H, or combined. But it should be quite soon!

@@SimRacingCorner Yeah I just saw a teaser video from moza the other day. It’s definitly h-pattern but they didn’t say if it was sequencial as well. I’m hoping it is. It would push others to release something high quality and affordable as well.

Everything from Moza I've tested so far has been great, so looking forward to giving that one a go too.

@@jacoblarsen4633I saw some pictures and unless there is a secret somewhere there does not appear to be a selection for sequential. Still, it looked nice enough.

@@SimRacingCorner It's a H shifter sadly

At 3:20 on the right side. End of the spring above the oval shaped hole. Grease doesn't help

​@@Michelsen3Kcan you try loosening and rotating that rod it rests on

It's just standard 40/40 aluminium profile, and regular aluminium profile angle brackets. Nothing special, you can find this stuff online from aluminium profile vendors.

I should have the Sim Jack h-shifter arriving this coming week.

@@SimRacingCorner Thanks I'm excited to see your review

I think it comes greased now, someone mentioned this recently. Otherwise I can recommend lithium grease

Lithium

The mount is something I put together, and not included

I'm wondering the same thing. Debating on this or SRS

The TSS with the plunger mod is just as good, really.

@@SimRacingCorner Thank you!

eBay has lots of shifters, so I don't know which one you mean.

That would be a good one. I don't have plans for that right now, but it's always possible.

Free shipping and no customs fees.

@@SimRacingCorner how many days did it take to reach home?

@@jerrygeorge007 A couple of weeks

Thanks for all the information, your channel is gold when it comes to finding such value for money products. Keep up the good work.

Works with any PC racing game where you map a shifter.

@@SimRacingCorner thanks, great video, gonna get me one .

Ignore that. That's just for the board.

It should be consistent in both directions. Looking at yours, it looks a little offset in the resting position and not centred in the cutout. You can see that versus mine in the teardown segment of my review. kzfaq.info/get/bejne/n7uRa6Rlp7SmoKc.htmlsi=-gF40qp8b9C6GaCI&t=204

Thank you for taking the time to reply & confirming that for me mate I sincerely appreciate it. It definitely wasnt centering properly and after more hours than I care to mention trying to get it right including flipping the spring which just changed the direction of the play...I've ultimately settled on shimming the leg of the spring with some aluminium can rolled into a sleeve which has centered/got rid of the play but has made that direction maybe a touch softer as I guess it's got a kind if pre-load on it now but it will have to do

​@@SimRacingCornerG'day again mate, I've tried posting this over 5 times but it keeps getting removed on my end...I think initially due to an Ali link but then full name reference? On an unrelated/related note regarding the Simjack sequential, I went for the short handle version but on the off chance I needed more height I also bought this gear knob from Ali which arrived today. "Epman Real Carbon Stealth Adjustable" kzfaq.info/get/bejne/l5hyZ5SQ26euiYE.htmlsi=739J2P1w2HmgCrdl Its quite a nifty solution but also cheap, great quality & has a super nice look & feel so I thought if you haven't come across it, it might make a good short review as I'm sure there are others out there that could make good use of its custom height adjustable design for any type of shifter but I think it's form alone especially lends itself to a sequential shifter & also gives a more substantial feeling over the already nice stock Simjack alloy knob. Cheers