I would love to see more videos about useful upgrades for the X1!
@DutchDeveloper6 ай бұрын
i would love to see a follow up video :)
@iainhay28236 ай бұрын
Like the look of this👍 watched it tonight at Schiphol which seems appropriate
@vincentgolzinger60172 ай бұрын
+1
@adamklosterman89606 ай бұрын
Ive had one of these for a while now. Found it works well about half the time, works so so about 25 percent of the time, doesnt work at all and had to be reprogrammed about 25 percent of the time.
@Exstaz5 ай бұрын
I got the extended one and it works flawlessly. Just such a nice add on.
@NickKarpen6 ай бұрын
Did the same, but with a Dig-Uno, WLED and Home Assistant. Nice to be able to create my own automations around the printer. I also used a new 6 pin ams cable cut in half to power the Dig-Uno.
@Interbert6 ай бұрын
Yes, i would love to see a follow up video
@blm79296 ай бұрын
Have it since months and globally happy with it. It works without problem except that after weeks it started to enable blue light all the time... the developer said me to just unplug the blue channel. I also selected to not turn green or red at the end of the print but it does it anyway. Apart from that, it's great.
@jimgentry58Ай бұрын
Yes, could you please have a tutorial to build this unit into my X1C I would like complete tutorial to install this unit for the extended. I am just getting into 3-D printing and I need to have a white. I’m older and I really need the light so I can see.
@steffenfrkjr14246 ай бұрын
More of this type please
@rodneysmith17506 ай бұрын
Great video Mark, keep them coming. Wish that you had a K1 Max though.
@MarkWattTech6 ай бұрын
I have a K1 Max! Actually looking at creating this same setup but with a zigbee lighting controller 😁
@rodneysmith17506 ай бұрын
@@MarkWattTechCool! I'll be hanging around and trying a few things on my own with Home Assistant and the K1 Max lighting.
@thespencerowen6 ай бұрын
Fantastic!
@alexdhaydenАй бұрын
Can you make it control ws2812 addressable LEDs?
@OldManJimmy16 ай бұрын
Full setup Vedic please.
@ljohnso162 ай бұрын
why could we not use wled and a standard esp?
@Jnibbs243 ай бұрын
I got this installation wasn’t difficult but when I hook up my LEDs they just flash
@Tafmie4 ай бұрын
Is it possible to explain more in detail how to add this BBLED as a device in ESPHome in Home Assistant? I don't see it auto-detected.
@xXB3t4Xx4 ай бұрын
Hello, great video as always! I finally received my BL led controller and I'm not really satisfied with the result with the current firmware, so I wanted to install Wled there but I'm blocking it...what is the configuration of Wled to use to run rgbcct leds? Which gpio pin to indicate? I don't currently have any reaction from the led strip 😒
@kielhawkins95296 ай бұрын
What is the benefit of this over an off the shelf zigbee or WiFi led controller hooked up to home assistant for automation?
@edgleyАй бұрын
Did you have any issues linking your X1C to Home assistant? the Greghsp work through only gets so far for me and then I can't get it added due to an error at adding the printer credentials
@MarkWattTechАй бұрын
Heya. What's the error you are getting? Do you have 2FA enabled? If so it won't work due to a current limitation on the Bambu Cloud
@edgleyАй бұрын
@@MarkWattTechhaven’t got 2FA I keep getting something along the lines of “invalid credentials” when I get to the stage of inputting my IP and password. Initially it was getting stuck on the input of my Bambu log in but that seems to have rectified itself
@martemchuk6 ай бұрын
why not to use normal led and automation?
@brettryan87376 ай бұрын
could you use addressable leds to follow the x and y axis of the print head
@leemarsh52586 ай бұрын
It doesn't look like the integration reports the x/y axis so unlikely. It does report things like % completed and layer so could maybe automate to change colour based on percentage complete etc.