As a professional cabinet builder and finish carpenter I like to watch these types of videos usually for a good laugh but this guy is actually offering up good sound advice. It is true “sneaking up on a cut” is a real term used. For the people who don’t use miter saws or much of any saw and trying to cut angles you have to realize and understand cutting rough materials like 2x4’s are a bit of a challenge for anyone because it’s rough lumber. Rough lumber is typically not straight or its cupped or worse it’s twisted. All of this affects cutting angles in the worst way. Even finished trim or cabinet material will not cut exact if it’s not straight and flat and square. If your doing a project buy an extra 2x4 or piece of trim so you can have a little extra in case you make a mistake or just need to make several cuts to get a little confidence or familiarity with the saw. I get that you want to save money and only buy what you need but if you don’t do this type of work daily or at least as a hobby your gonna make a mistake. As a professional who does this type of thing daily I make mistakes. It’s just the reality of it so just relax and give yourself a reasonable chance.

Thank you for the tip to "sneak up on" that second cut, that'll be something that helps me out in the future.

As always nice simple and to the point dialogue, so helpful for newbies. 👍

Your sound edits are great. Thank you for this. I am re-framing the inside of a travel trailer using 2x2's and going to use this in the corners and put it all together with pocket hole screws.

Very helpful!! I've always struggled with this, thank you for showing a simple solution that I can easily remember how to use!!!

I'm an absolute newbie at this so thank you for this very informative lesson.

Thanks man! Its like this video was made specifically for me. Currently following a cut list from a KZfaq video and now I know how to get my miters to an exact length. Thanks again!

Thanks Stan. I'll be using what I've learnt from this video and the angle cut video next week. Someone hired me to organize and tidy their basement. Part of the process is building some shelving.

Watched couple of other videos before this but yours helped me to understand how to make perfect miter cuts. Thank you so much!!!

Hey Stan! this video was helpful for me!! I am using a metal cold cut saw with only one direction on the miter. You cleared my thinking!!! Thank you!!

Hi Stan, great tip on cutting angles. I've always struggled with angles. Your method will help me.thanks again.

Great video! I find it difficult when you have to cut mitre joints to a specific inside dimension. Measuring and marking the inside angles is more difficult however once they are marked the sneak up to you line method is the same.

Great video Stan Sullivan, and very informative! I recommend that viewers WATCH this BEFORE YOU CUT! Liked & Subscribed as standard.

Liked and subd! I'm very new to wood working and this video was a great help to me. Especially with my next project that requires several angled cuts. Thank you sir!

I’ve been holding off trying these for exactly the reasons you mentioned! This video made so much sense! Thank you!

Very few things in life take pure talent or strength or speed. It's usually all about knowing the techniques. The technique you just showed is extremely helpful and will help me in my current project. I look forward to seeing more of your videos where I hope to find more useful techniques. Thanks for posting it!

The thing you hear most woodworkers say is "I sneak up on the line". GREAT tip Stan and thanks.

"Sneak up on it", I like that idea, I will try that method. Thanks for sharing.

This helped me to better understand my "angle block," thank you! Also I chuckled at the random gardening snipping cut in you added. I thought the angles of the tomato cages were some how going to play a part LOL! Subscribing!

Thanks for this to the point video - very well made and easy to understand!! Just got my miter saw and trying to figure it all out

damn for whatever reason this made it make sense in my brain. thank you!! made my very first miter cuts today and they came out PERFECTLY, it's probably the most satisfying feeling I've ever experienced lol

Just on this one video I am Subscribed! I know there is probably a hundred tutorials on this, I know I should of looked it up years ago... But here I am, I've finally looked I got your video, it was easy and you showed the stock block part which I always forget. I'm set to cut some miters!

Every KZfaqr giving simple instructions using a 2 thousand dollar saw 🤦🏻‍♂️

Buen trabajo amigo! Very well explained thank you very much for sharing your great knowledge and humility with all of us.

short, crisp and clear - Excellent. Thanks

This video showed me a fast way to do this , without complicated jigs. Great tip ! Thanks!

I'm building these shelves today! Thank you for the video!

Great tips Stan! Especially the sneak up on it

Being a novice woodworker i had no idea how to make angle cuts that would fit. Today i got too frustrated and called it a day. Tomorrow is a better day thanks to this video!!! Thank you Stan!!!

If I cut my boards too short I just use a board stretcher.

Made my cuts today, thank you. I’m a newbie and I put my project on hold for 3+ weeks because I couldn’t figure out how to make them until i came across this video. Again, Thanks.

Very informative in a way even beginners like me can understand!… that nighttime’s nature bit though bought you the subscription

Yes! Thank you!! This is exactly what I was looking for.

Thank you, I've been looking for this exact video, gone thorugh more than 20 before finding it..

Good tips. I don't tend to sneak up on the cut though. I usually just line up by bring the blade down while it's off using the teeth to line up the cut.

Appreciate the information, thank you for making the video. The only thing I would suggest is to show the finished product. It would be nice to see that all your angles came out the way you wanted them to.

This was extremely helpful. Thank you so much.

I wish I had looked you up before I wasted one board - at least it was only one. Thank you so much - your teaching was great but perhaps including same angles going same direction for a roof on a shed slope (building a firewood shed and I goofed on the rim rafter angle and now I know what I have to do.

That was Awesome Stan , thankyou so much for Sharing that . I was doing a 45 cut one way and the changed the saw to 45 the other way I was getting hell confused , this was so easily explained , again thanks

Wow. Now I can make a stand for my adjustable dumbbells (doesn't REALLY require and angle but makes it easier the wrist) and the angle was keeping me from making one. I'm WAY late into being a carpenter but weekend warrior projects as a hobby I'm a fan of. Something easy...like a step stool! Thank you for the vid. I

Thanks man. This is going to help me immensely.

Dudeeee 😭 Why was I having such a hard time figuring out how to do the second cut lol It was as easy as rotating the board lol 😭 Thank you lol And thank you for the stop block tip!!

Good video, Stan! Very helpful!

Thank you so much. Is this the same way you measure when the blade is tilt at 45 degree?

This video just saved me so must frustration. Thank you.

As a beginner I say thank you. I'm glad I came across this video because I just made the same mistake by just cutting all of my boards at a 90 degree first 😬😱. Btw, the project I'm doing is from a video with instructions. Lol I do have extra would (yay). I will go and practice on that before I fix my problem. 😱😄

Thanks Stan, I need as much help as possible, I always screw up angles which is why I try hard never to have any. I have made two planters and I have to trim the top like the facing on a door - but I have put off - because I know I have to cut them at an angle. Drives me daft.

I've been trying to figure that out for quite some time now... Thanks

So glad I found this video!! Thank you

Hey Stan nice video , im making a floating workbench and starting with the brackets im wondering hiw to measure the 45 degree pieces properly , and suggestions ? Im just getting started to woodworking thanks

Best/easiest advice so far

thanks. that is actually something i was always nervous about

Question I have is I have a home built in the late 50's one of the corner rafter tails has damage so trying to cut correct angles which generally is at a 45 degree cut at each side of the 2x4 stud though my facial boards pull in slightly at an angle the bottom facial boards are farther inwards as the top is farthest out so how would I figure out the angle cut from top of 2x4 to the bottom of it & then yet able to have the V cut from top to bottom?

Wow! I'm struggling with putting "X" bars on the sides of my console table that I'm building and I think this just resolved my issue. Will have to try it when I get back to it.

I've been hobby woodworking for years deck boxes, window planters and simple stuff. Each new project i swear I'll take my time measure three times, I got it this time. Yeah sometimes I hit it, some not. And I do use the sneaking up i learned that from a house finish trim carpenter years ago. Thank you very much for this helpful tip, I have bird feeder pole to build with 4x4 s I already have enough scraps . Just the tip that I came here for.

This is a lot of good advice! Thanks for the video!

Thanks for the video. So if someone says i cut the board tp 24" with a X bevel the total length of the long end should be the final length?

Thank you for posting this! I made a mess of cutting mitres today with 1"x6" board for the top of a planter. Bit of a war-zone! I should have watched this video first lol!

hey whats up stan, thanks for the video, do you have any video with a round wood, i need to doe the samething but with a brum stick with a 60°

Hi sir, thank you for the great video, this was a great tip. My only frustration is when you have two different angle on the same board, I often get confused and when I think I`m Finnish I have cut the same angle in both ends. Do you have any tip for that?

Great stuff man glad I found ur channel

Can you tell me what method is used to put crown molding on a curved triangular wall without a corner that has a sloped or vaulted ceiling

I need to cut 6 pieces of bracing for our porch area to go against a 8x8 cedar post. I measured and it's 24 inches so I need 2 for each post and we have 3 8x8 cedar posts. So, I need to make two 45 degree cuts on each 4x4 posts that's 24 inches long. How do I do this accurately? I did a test run on a 2x4 and the cuts weren't accurate when I put it up against the 8x8 cedar posts.....I was off a bit. I need some help. Thanks

Thanks for the video Stan. Hopefully tomorrow I can avoid the temper tantrum! LOL I like your chop saw table extension too!

what a fantastic method...thanks!

Great video and info! Thanks!

Simple video with great information. Thanks

Great tutorial, thanks!

Thank you...way easier than I thought.

Wish I watched this video sooner; in the middle of a project, cut all my wood to length then cut angles after. And of course now my pieces are short. Lesson learned!

Nice, easy to follow instructions with great video graphic details. Thanks and great job. BTW, how do you like that miter saw? I want to get a sliding miter saw someday.

Great tips, and thanks for sharing! :)

I tried to miter a cut but it has never come out right and I struggle with angles but these are the cuts that I want to use for my garage project. Ty

Any recommendations for making long shallow angle cuts in a 2x4? Like a triangle, 9” length both angle cuts on an angle of 22.5 degrees?

2ft x2ft ceiling tiles. I need stake points on both ends of my 2ft trim pieces. I’m using 1x4 for trim. So it would be 8 45 degree cuts per intersectional joint and 2ft from point to point on the individual pieces. Does this sound correct?

how do i detrmine the overall lentgh of my top support opiece that will hold the top layer which is 2ft in width? do i base the cuts at 24 inches + for the mitre cuts for a bracket support?

Is there a way to do the same but on the table saw using the fence to measure the ditance? Every time I cut 2 x 45 degree on a board I mess it up.

I have a rectangle made from 2x4s and need another 2x4 to go diagonally from the top of the rectangle to the bottom. How would you find the angle without a speed square?

Great tip! Subscribed

How would you go about connecting your cuts to make a solid frame?

Great explanation

Thank you for making this video

Name of my new band "Sneak Up On The Cut'. Good advice. Funny. Simple is always easier than I make it out to be.

Great idea. Thanks

Cheers buddy. this actually helped me a lot.

Great vid!

Is there an adjustment on a Makita 2704 to make the wheel marker go to 45 degrees?

Great video! Thanx

Excellent. Thank you.

Where do you measure from if you're making two miter angles that are both parallel to each other. For example where do you measure a 4-in cut that is parallel at 45° angles parallel from.

Nice job.....I'm putting on a car port on side of garage.......how can I figure what angel.....thanks Stan

Thanks so much I will try it tomorrow morning

Thank you for the video, I appreciate it!

i don't have a saw like yours i have a table saw is it possible to do it with a table saw? and how would i do it. i have another project on my mind that i would like to get done for Christmas ( a fireplace for stockings )

nice job. easy.

Thank you!!! I could NOT figure out how to do this.

hey man how about doing that with a hand held circular saw? i do not have the saw like you have there. no room in my apartment.

How do you measure the length of the board when factoring in the 45 degree angle cut?

Good tips.

So helpful, thanks👍