SketchUp 2018 Tutorial Applying Textures onto Curved, Circular, Convex & Concave Surfaces

Рет қаралды 70,095

Mike Winter

5 жыл бұрын

Sketchup 2018 Tutorial Applying Images, Photos or Textures onto a Curved, Circular, Convex & Concave Surfaces

Пікірлер: 26

@davies7283 5 жыл бұрын

Thank you so much for this. I have been having problems wrapping images around edges and cylinders. Please keep it up.

@louismoorales4805 4 күн бұрын

gracias tenia como 12 hora intentando para un trabajo de la uni, en la versión web

@engrabril 2 жыл бұрын

using it for a few years and now I want to upgrade and I'm happy I did that.

@ahsom2322 Жыл бұрын

thank you so much for this ;D

@arnoldferrera1185 2 жыл бұрын

thanks for sharing! excellent

@dienabidin 3 жыл бұрын

Thx mate its works

@elpoetaanonimo849 4 жыл бұрын

I fucking love you man.. i was trying to figure out how to do it.. i waste hours and hours.. THANK YOU !

@akshayyamajle7299 3 жыл бұрын

Thankyou soo much!

@richardvankesteren7013 2 жыл бұрын

Hello Mike, how would you apply a png-logo image on a tank of a 3D Harley Davidson motor. The png is partly transparent and the tank is very curved in all directions. Where the transparency is from the image, the metallic car paint, which is applied on the tank, should be visable. Hope you have a solution.

@angiepigar6571 Жыл бұрын

Thank you!

@xuantien147 10 ай бұрын

thank you !

@santi-architect 5 ай бұрын

Thank you so much

@ricksjordan2863 Ай бұрын

thank you so much sir

@masood6086 3 жыл бұрын

THANKS FOR SHARE

@rajendiranp122 2 жыл бұрын

good job

@gustavohfmota Ай бұрын

Thank you

@chezhiyan.m5331 3 жыл бұрын

Good

@WallyJ2K 3 жыл бұрын

I need to do the reverse. I have a 50 gallon drum and I am putting a pipe into it, off-center, and I want to cut the hole precisely... So, once I extrude the pipe cut out of the drum, how do I print a flat representation of the hole, that, when printed, will look a bit like a teardrop shape?

@mikewinter8719 3 жыл бұрын

Walter Johnson I’m not sure I understand what you are trying to achieve? Are we talking about applying a texture?

@WallyJ2K 3 жыл бұрын

@@mikewinter8719 No. Somewhat the opposite. In Sketchup I create a cylinder (55 gallon barrel). Then I create another 2 inch diameter cylinder which will be a pipe. I turn the pipe 90 degrees because it will go horizontally into a hole drilled through the side wall of the barrel. Simple enough. Here's an image of what I'm describing: pasteboard.co/JuHlUNX.jpg. You showed us how to apply a flat texture to a rounded surface. I have a rounded surface with a hole cut in it that I want to make flat. Then I can print the "hole" and put it on the barrel to make my actual cut.

@mikewinter8719 3 жыл бұрын

Walter Johnson I’m afraid I don’t have an easy solution for that in designs terms, but in practical terms it’s as easy as using a hole cutter at the required diameter of the pipe and just drilling the hole, the angle will create itself if you drill at the correct required angle the pipe will insert.

@WallyJ2K 3 жыл бұрын

@@mikewinter8719 I thought about doing that, but the hole saw will get difficult to control the more the hole is cut, or so I think. Thanks for the suggestion.

@-._.-._.- 3 жыл бұрын

@@WallyJ2K still trying to do this? Just select both shapes and do right mouse click and intersect. Delete the pipe and there is the hole