You're welcome.

Thank you! You saved me a nervous break down!

You're welcome.

Edward Braiman i was looking at your skr playlist and i seen one of your videos is private, is it supposed to be private?

You're welcome.

Thanks, I've been working to improve the thumbnails. I'll probably be updating them during the holidays.

You're welcome.

de nada.

Thanks.

Thanks.

You're welcome.

Spacba.

@@EdwardBraiman Spacba = Spasibo = Спасибо = Thanks! With pleasure I look your video reviews, I wait for the SKR PRO V1. 1 and I will upgrade the printer.

It's a very challenging board.

@@EdwardBraiman I know it's a complicated Board, but there's a lot of potential in a motherboard with a powerful microcontroller on Board.

Thanks.

Set serial port in configuration.h to 0. It should be defualt 0 already. Is Cura or Pronterface already communication occuring with board during build in VScode?

Which part of the video? Pronterface?

Managed to figure it out. I put a bridge on the board for the rotors. The only thing is i need to do is set up upload_port in platformio.ini

Thank you.

Most the time you only need to change the motherboard type to setup similar boards if pins are connected correctly.

Check the jumper for USB on the SKR 1.4 board. Also check and see if it appears in device manager.

@@EdwardBraiman I had the jumper on USB and the second board with it on computer power, it would read the drive from the computer, but after updating the firmware and placing it on the SD card the screen still read No Printer Attached. It shows up in device manager, but with a caution emoji. Moving the jumper, firmware was updated, but it still read No Printer Attached. The Visual Studio Code program could not connect with the card in order to test, if I put the printer cable in my old card the program finds it right away. I tried different ports in the platformio code, but none worked to communicate. I sent the card back and will be trying the standard V1.4 card non turbo. Thanks for replying with suggestions. I am slowly figuring things out from watching all your videos.

It's a binary file, unsure how to decompile. Easiest way the to modify a new configuration file and compile.

Which sensor are you referring too?

Do you have Endstops connected to them?

It's possible.

I've not put an oscope on my SKR 1.3, but the SKR 1.4 is about to be tested more closely. The SKR 1.4 seems to have issues with a 5v inductive sensor and BLtouch. If you would like I would post a question on Marlin firmware bug database to inform others of your observations. I would further suggest contacting bigtreetech and ask them what this is about. Nice catch.

Looks like I need to order an oscope as I only have a logic analyzers and don't want to bring boards to work.

@@EdwardBraiman Check out Eevblog's review of the Rigol DS1054Z! And be sure to check the forums, too!

Could you explain the question a little more?

It may require Python to be loaded. My system had it loaded before tutorial. Also GIT might be required.

I'll try it out on my new computer.

Okay just tried and I see your concerns. I had to install GIT and python 2.7. I then had to point to the python.exe in VScode. Then wait for Platformio to update and restart VScode. First compile failed of unmodified Marlin firmware. The second compile then worked. I originally ran python 3 with no success. Only python 2.7 worked so far with my install. Let me know if it works for you.

I'll see if I can record video after reloading windows 10 this weekend.

Are you using ATOM or VScode with PlatformIO? After making video Marlin changed to only supporting VScode with PlatformIO. There should be a video in playlist in description.

@@EdwardBraiman vscode

There's a link in description for Discord I think. Enter general chat and post configuration.h and configuration_adv.h and I'll take a look.

Unfortunately I neither email or mail things to people.

So you compile and load firmware and power down and back up?

@@EdwardBraiman yes, compile, load fw on sd card, power down, power up but nothing happens.

What is the size of the SD card?

@@EdwardBraiman it's 16G

Normal size for drive will be 128mb, something I learned after this tutorial. If you can partition lower half of drive to 128mb the board should in theory be able to read it.

In the past when it was set to zero, it would not connect to computer to use.

I'll try and demonstrate on stream tonight.

At 6 PM EST.

You need to used VScode, because they're the only IDE that supports Platformio plugins now.

I understand why after the last couple of days trying to compile Marlin firmware.

It does take slightly longer to compile but 40-50 secs versus 38-48 seconds is a price I am willing to pay to no longer use Atom. I am not sure why everyone, including the official people, jumped with Atom.

In my case compiling errors became too difficult for recording tutorials. Also the display it's much easier to present tutorial. It does have a registry entry to track screen position I need to modify, because I want to be at the top of each file and not where I last was on another edit. Other than this it's manageable.

Yes, I figured it like this and that is I used MSVC for a decade back from 1998-2008 so why not Visual Code? What I really dislike, and I honestly have no understanding why this is, is that the compiler is gcc is VS Code and not the Microsoft one which I always found superior over gcc. Besides that part I have not had a single issue since ditching Atom.

This error general means USB cable is not connected to board and computer or the jumper on motherboard is set to PSU power and not 5v USB.

Edward Braiman hi; The problem was not the USB cable , but me not following your instructions exactly on creating the file in the card Now I’m able to find the card on pronterface , but now a new problem come up , and its the when I try to compile with the repapdiscount lcd options, it gives me a few errors and does not compile. But I think that I can trace the error . Thank you for your help , I will keep you updated Mariano

You're welcome.

Unsure, I might have python loaded by default. Try loading python.

@@EdwardBraiman I think I got it. Thanks for the quick reply though!

Not yet, need a lot of safety equipment.

my mechanic in my k40 with sgen l ist. but i have no idea how to conect the laser wird and wich lines in config.h musst change

A clue is to read pins file for RAMPS, but remember protective filtered laser glass. The only reason I avoid the video is up front costs are hundreds of dollars.

Also the air needs to be vented correctly.

What's the first error when compiling? What's the board you're trying to compile too? Is the SD card connected. Is the jumper on 5volts?

@@EdwardBraiman i get same error my board skr mini 3.1.2 lpc1768

What's the chipset for mini in boards.h?

@@EdwardBraiman i tried them all in h that is affiliated with skr mini none work

First pick motherboard in configuration.h as BOARD_BTT__V1_1. Then in platformio.ini for default environment STM32F103RC_btt if you board is SKR mini v1.1

I did save my compiled marlin files ready to upload to the printer, but before it could be connected, lights out.

Will it allow you to reboot and then copy over?

Patience, perseverance, and a little luck= success!!!😁👍

@@patrickbodine6010 congratulations.

@@EdwardBraiman thank you. Your videos were a great help!😁👍

There's a free Discord link on channel and 800+ people in general chat to help.

Do you see a temperature with M105? DO you see anything in Pronterface for bed temperature?