Really nice overview and review. Cheers!

thanks man u saved my life i had a traxass maxx and had same charger as you and i did not know how it worked

How can the SKY RC be calibrated? My charger shows 3.6V on the display, but when I measure with a calibrated Fluke multimeter, the meter shows 3.3V. That's a big difference. Please write how it can be calibrated.

Hi can you advise what wiring I would need to charge a LIPO battery with JR/Futaba RX plug as I see the SkyRC T100 has female XT60. I'm new to hobby and trying to order the right wiring for charging the transmitter battery.

Hi i got the same charger, lately i found an issue while charging my NiMD batteries 8 Cells to be exact, on A channel everything is going fine, while shifting to channel B and charging the same battery cells it currently stop and goes back to the welcome screen, i don't know what's going on?? I would appreciate your help regards to my problem.

is it ok to charge the 5200mAh 2S 7.4V at 12A, given the batt is rated at 5.2A? Also, if there is a 2C charge rate, that equates to 10.4A max, which is still below the 12A chosen in the vid.

I see you are using a 2c battery. So if your charging a 5000mah 1c battery surely you can only charge at 5amp max? On a 2c 10amp. Do you not have to therefore adjust the charger to the correct amperage? Thanks

Can it check the IR of a battery?

Any good for balancing hybrid battery modules? In comparison to the Tenergy T180 100W Balance Charger, which would you suggest is better?

Can I plug this charger to my car cigarette plug to charge my LiPos? TIA

Great products. Are any of the Hobbystar 2s lipos ROAR approved??

Can i charge a HV 2s lipo on this charger?

2 downsides I see, but looks like a great charger at a great price.... 1. No leads or adapters at all, no balance boards, etc.. and since it is XT60 outputs, many people who have previous chargers likely have a handful of different leads set up for chargers with 4mm banana plugs... I will have to build/adapt a couple leads I guess... 2 , and a minor downside... no USB port for powering devices ,which is pretty handy... I'd totally pay like $30 more for a a USB port and at least a couple charge leads so it was usable out of the box with batteries other than ones that have XT60 plugs... If they could make like a 200w x2 with USB and some adapter cables, for say $199, I'd be in for sure... Looking for a new charger with a touch more power than our Venom dual and Hitec X2 dual... my son moved up to 1/8 scale with 4s, and I have my eye on a 6S plane...

The plug in the charger i just for xt60 or xt90?

OK I have a question I understand voltage multiplied by amps equals watts and when you're talking about 100 W of charging power you divide by the voltage my question is should you divide by the nominal voltage of the battery like you said 7.4 V for two cell or should you divide by the max voltage which would be 8.4 V on a to sell to get the comparable amps For the actual white no one has ever answered this question because in my opinion, when you get up to four port closer to 4.2 V for sale you're still adding more power even with the same amperage please correct me if I'm wrong.

This device has a huge problem, when you charge / discharge using only the main power port it'll not reflect the voltage correct, so it'll finish charging / discharging before it gets to the required voltage. It can be solved by connecting the balance cable which will measure the voltage correctly... But then there are 2 more problems 1. The maximum current that's allowed is 0.7A both in charge and discharge 2. You'll have to disassemble the battery if you don't have a direct balancing connected all the time which is annoying

can the voltage be calibarated just in case I find it not so accurate?

How do you discharge the battery

How do you know when it’s done?

I dont like that the t100 only cost $49 in the usa. But the t200 is $109 which is more than twice as much. Imo the t200 should be priced around $89

I just got this charger and it just charges for a second then shuts down and restarts

Ok ... so I'm new to the hobby and all these numbers and acronyms .... yeah, I'll pick those up over time I'm sure. My questions are .... if I buy this charger (currently AUD$165) and one of those bundles with all the connections, will it last for eternity (or very close to it)? I don't have a preference for fittings - will this charger work with one of those AUD$20 bundles I've seen? I'm mainly interested in bashing RC buggies with my 5 year old son .... maybe some rock crawling because my first full build will probably be a B16KM. I can see use for a dual port because my 7 year old daughter participates intermittently. Thanks for any info :-)

I calculate it based on 4.2v per cell… after all that is what we ask from our chargers 3s 5000mah @1c rate requires 63 watts and 5amps 6s 5000mah @2c rate requires 252 watts and 10amps to efficiently fully charge all 6 cells Not sure why people do the maths based on 3.7v per cell

The big downside of this charger is that is doesn’t support 1s / 3 cell Nimh.