There are more things to do for success: 1) Start with a good running warm/hot water flush to dislodge as much dried up ink as possible 2) Try also using "classic" windex which I found does a good job of dissolving ink, but you may have to let it sit overnight or longer,and get one of those two spouted funnels (ebay) which you seat over the two inlet orifices (so the print head needs to be assembled and either filled with ink, if the areas around the jets look good, or partially filled with windex or print head cleaning solution). Then use the outlet sealer which comes with the funnel and provides a silicon outlet tube for mounting a syringe body over the print head jets area in order to apply suction and/or pressure to force the ink or solution back and forth, or just out through the print head area.This solution or ink is what is added to the funnel tubes/ reservoirs. The idea is to use pressure and suction to recover the normal flow and break up the clogs around the jets.Not much flow will take place, just enough to swish the solution in and out a little. 3) Having done that normally you would take the print head apart again, clean it with water if necessary, fill it about 2/3 or so full of ink, and put a cover over the print head orifices until you get it assembled, so the ink will not leak out, which it will do if uncovered. 4) After sealing the print head parts back together, shake the print head somewhat to dislodge air bubbles in the screen at the bottom of the ink well. 5) Then hold the print head upside down, take off the cover you put on over the jet area, and apply positive air pressure to each of the two silicone sealing orifices, which normally will be on top of the print head when installed, but now need to be at the bottom. They are the clear silicone round orifice seals. The pressure has to be applied from below with a suitable syringe so as to make a good seal on the silicone seal hole so the air bubbles come out the top. Doing this carefully while observing the orifice area you will usually see a quantity of bubbles escape, which is crucial. Try to apply just enough pressure to force out all the bubbles so that then a nice clear flow of ink appears. You don't need to do the pressure too long or too much, just so a nice clear welling up of ink appears. Attached to the top part of the print head and sitting inside the ink wells are things like a butterfly valve which expands when the pressure is applied forcing the air bubbles out. Then clean off everything.
@ng58988 жыл бұрын
+Merrill Sloan , if you ever get a chance, put up a video of your description you have described here. I think you would help thousands and get a lot of hits on KZfaq! Thanks
@mohamedkamal3157 жыл бұрын
I totally agree with you. @Merrill Sloan you can do it.
@TheZeePeople7 жыл бұрын
Holy crap... I'd rather spend the money on new printheads. Seriously.
@gold3nrul3118 жыл бұрын
Awesome thanks dude. Got my black printhead finally working!! I had taken the printheads out before for alcohol rinse, but the black dried up. I took it apart thanks to ur video and did internal alcohol rinse and left the parts a bit wet, thankfully I had bottles of ink from Amazon to refill. That's probably the most important thing about this method, you need ink ready to refill the printhead. But yea, I didn't let them dry out completely to prevent the ink from clogging again and did about 5 alignments/cleanings or more... took awhile but got it working.
@DABIGRAGU17 жыл бұрын
Followed your directions, my printer heads were dirty. Your video fixed our problem! Mahalo!
@alexandermena3432 ай бұрын
Gracias
@En_Dry3 жыл бұрын
Выручил, братишка!))) Благодарю. Кто не понял - скотч обязателен, ибо в этих каналах шарики и их не видно под краской. Остальное интуитивно.
@IowaKim8 жыл бұрын
I am bookmarking this video-thanks for the great hacking job. I think my issue is an "end of life" issue as both print heads errored out at exactly the same time. So looking for how to reset this.
@stephenbruck69945 жыл бұрын
I love how 6 minutes in, you mention that you definitely need some weird thing that no one has. lol
@AlexeyaLu6 жыл бұрын
Where can I get the little metal balls? I think my bf lost one and that's why my yellow suddenly doesn't work...
@1gurugraphics5 жыл бұрын
Very good information.......Thanks
@jackw32356 жыл бұрын
Thank you for the education
@mrhammersutube8 жыл бұрын
Great video's on the 8500a, thank you! I have cleaned the print head, still a problem. If the vacuum pump was bad, would it effect the other print head?
@eternalhope82019 жыл бұрын
Where can I buy the bb's? I think I washed mine down the sink when I was washing out the CYAN/MAGENTA printhead. My printer still says "The following printhead has a problem: black/yellow" And I didn't lose the bb's on the black/yellow one.
@slussermanner069 жыл бұрын
+Eternal Hope Honestly, I don't know if you can buy the BBs separately. I just happened to have purchased a used printhead on eBay and it turned out to be already broken so I just saved the BBs from that one.
@martinezlopez46994 жыл бұрын
REALLY gr8 Job √√
@mohamedkamal3157 жыл бұрын
Thank you for the video. I followed the instructions and cleaned the head. Now what is the next step, should I install it on the printer or should I have to fill it with ink first, if so, how?
@DABIGRAGU17 жыл бұрын
It will fill automatically from the cartridge. You probably already figured that out since your post was 2 weeks old. LOL
@gwhitcutt6 жыл бұрын
You are on the right track, but if you intend to develop any more DIY videos that require close-up imaging, please change out your camera. Watching the video with the lens shifting in and out of focus is very distracting.
@robertshade8631 Жыл бұрын
Hello i recently installed a yellow print head and got printer interface which seem ok.Then error code C00EOO60 appeared and can not move forward with printer setup.Any ideas?
@bngnyc6 жыл бұрын
In a nutshell, don't take it apart, try soaking it overnight first. If you are taking it apart, you'll also need to prime it with inks and also sucks the air infiltration with a syringe (you need to buy the kit), which this video failed to mention. Just get a printhead in ebay. it's alot cleaner .
@petermensing762810 жыл бұрын
Informative. Real bad focusing on this video though
@kuzyyynpro5 жыл бұрын
My printhead was clogged, did not print in yellow, then after a lot of test prints, automatic cleaning procedures I ended up with a printhead error on the printer. I saw a video with a solution that refilling the printhead with the special tool that sucks off unwanted air from inside and pulls the ink should help with the error. I don't have that special tool but I will try to disassemble printhead, flush it, and refill manually. Do you think will printer detect my unclogged printhead normally, without error?
@graphixprinters69126 жыл бұрын
CAN WE CHANGE THE SILICON VALVE OF INK TUBE THAT IS AT PRINTEHEAD SIDE????
@yeshecan710 жыл бұрын
Its really helpful, where can I buy those BB's in case I lost? Give me link PLEASE
@slussermanner069 жыл бұрын
+Tefera Ergoye Honestly, I don't know if you can buy the BBs separately. I just happened to have purchased a used printhead on eBay and it turned out to be already broken so I just saved the BBs from that one
@robthagoodest8 жыл бұрын
thanks for the video! Just one tiny critique. Sliver is the word. Not slither. Slither is what a snake does. Not trying to be a jerk. Just saying.
@X_PATHOGEN_X4 жыл бұрын
Who cares?
@robthagoodest3 жыл бұрын
X_PATHOGEN_X you did; enough to comment, anyway.
@benjamindiangelo4488 жыл бұрын
after cleaning and drying the print head, do I need to refill it with ink or does the printer automatically do it from the cartridges?
@mohamedkamal3157 жыл бұрын
I want to know this as well. Hope somebody enlighten us.
@DABIGRAGU17 жыл бұрын
Your ink cartridges will fill the printer heads automatically.
@jimbacker26859 жыл бұрын
Did you take out the fine screens on the bottom of the cavities?
@slussermanner069 жыл бұрын
+Jim Backer Nope
@doronamedey4 жыл бұрын
Where can I order spare bb's?
@severinmichel74919 жыл бұрын
y a-t-il en français. Merci
@ilyagorin40597 жыл бұрын
But with that fine screen or sponge the flashlight impossible to see...
@monisamontoya4015 жыл бұрын
My printer 8500a cost $99.00. Each printhead cost $80.00. Ink set cost $75.00. Cheaper to just buy new printer. When will ink prices go down?
@vicever085 жыл бұрын
why not buy a large refillable cartridge on Ebay, I used mine for 10 years. only refilled twice. Super convenient, much better than change cartridge once every 2 months.
@utube4greenfuture4 жыл бұрын
@@vicever08 The bigger problem is HP's ink cartridge ARC chips which now incorporate non-hp cartridges that prevent the printer from running after the chips have been tagged as empty.
@abbasiofficial3993 жыл бұрын
Hp desigent t1120 heada error
@Bastyon.4 жыл бұрын
Может кто переведет?
@normhansen24473 жыл бұрын
Spinning arrows. No play... Me? You? KZfaq?
@syedsnk17 жыл бұрын
ALMOST 20MIN JUST TO SHOW THIS.. BLABLA.. WASTING TIME.. HAHA
@utube4greenfuture4 жыл бұрын
Why aren't you tending your oil fields?
@AlexanderCyberian7 жыл бұрын
you need a microscope to clean your printhead????that's insane. I will accept planned obsolesence as default and buy a new one.
@asbcustom4 жыл бұрын
Millenial comment if ever there was one, they are planning their own obsolescence..
@utube4greenfuture4 жыл бұрын
Just don't buy HP... they think wallets are like ink cartridges.